Franklin Electric SubDrive75 User manual

SubDrive75/100/150/300/2W
MonoDrive, MonoDriveXT
Status
État
Estado
NEMA 1 / NEMA 4 / NEMA 3R
Quick Installation Guide
nEnglish ........1
nFrançais .....13
nEspañol..... 24

Contents
Location..............................................3
Wire Routing ........................................4-5
Grounding ..........................................6-7
Grounding/Generator Sizing ..............................7
Wiring/Configuration NEMA 1 .............................8
Wiring/Configuration NEMA 4 ..........................9-10
Wiring/Configuration SubDrive2W ........................11
Plumbing ............................................12
Accessories..........................................12
SubDrive75/100/150/300/2W
MonoDrive, MonoDriveXT
NEMA 1 / NEMA 4 / NEMA 3R
Quick Installation Guide

3
Location
Service Entrance
Panel
Mount drive to a sturdy
supporting structure (wall or post).
NEMA 1 - Indoor Only
NEMA 3R/NEMA 4 - Indoor/Outdoor
Mount the drive as close
as possible to the service
entrance panel.
Use a dedicated branch circuit for the drive.
Wire directly from the service entrance panel.
(15A for SubDrive75/MonoDrive/SubDrive2W)
(20A for SubDrive100/MonoDriveXT)
(30A for SubDrive150)
(40A for SubDrive300)
Allow a 6" (15 cm) clearance
around the drive for cooling.
Use the holes and
guides provided.
(DO NOT drill holes
in the drive.)
GND GND
Service entrance ground rod It is recommended to wire directly
to the service entrance panel.
(DO NOT wire to a sub panel
located in a home.)
Service Entrance
Panel
IN HOME
Sub Panel
GND
GND GND
6"
15 cm
6"
15 cm
6"
15 cm
6"
15 cm

4
Service Entrance
Panel
GND GND
When possible DO NOT run drive input
power or motor wires in parallel with house wiring.
Avoid running out-building wires in parallel with motor wires.
GND GND
Input
power Motor
Separate input power and motor
wiring by at least 8" (20.3 cm)
GND
GND
DO NOT run input power
and motor wires together.
Separate by at least 8" (20.3 cm)
Motor
Pump
Motor
Output lead to motor to
exit house as soon as possible.
8"
20.3 cm
Input
power
Wire Routing

5
Service Entrance
Panel
Service Entrance
Panel
GND
Motor
TV
Branch 1
Branch 2
Branch 3
8" (20.3 cm) min. 8" (20.3 cm) min.
8" (20.3 cm) min.
Telephone
If it is necessary to run wiring in parallel, keep
drive input power and motor wires
at least 8" (20.3 cm) from other house wiring.
Satellite/
Antenna wire
GND
GND
8" (20.3 cm) min. 90º
OK
Cross over other branch circuits
and house wiring at 90º.
8" (20.3 cm) min.
8" (20.3 cm) min.
GND
Wire Routing

6
Service Entrance
Panel
Service Entrance
Panel
Ensure that a
proper utility
ground rod
is present &
connected.
Service entrance
ground rod
Service Entrance
Panel
GND GND
L2
L1
An input power ground wire from
the supply panel must be connected
to the drive.
A dedicated output ground wire
from the drive must be connected
to the motor (motor wires and ground
wires must be bundled together).
Pump
Motor
GND
GND
Use the service
entrance panel
ground ONLY.
DO NOT run ground wire separate.
Motor ground wire MUST be bundled with motor wires.
GND GND
Avoid multiple ground paths.
GND
GND
Pump
Motor
Pump
Motor
GND
Service Entrance
Panel
Service Entrance
Panel
Ensure that a
proper utility
ground rod
is present &
connected.
Service entrance
ground rod
Service Entrance
Panel
GND GND
L2
L1
An input power ground wire from
the supply panel must be connected
to the drive.
A dedicated output ground wire
from the drive must be connected
to the motor (motor wires and ground
wires must be bundled together).
Pump
Motor
GND
GND
Use the service
entrance panel
ground ONLY.
DO NOT run ground wire separate.
Motor ground wire MUST be bundled with motor wires.
GND GND
Avoid multiple ground paths.
GND
GND
Pump
Motor
Pump
Motor
GND
Grounding

7
Service Entrance
Panel
Service Entrance
Panel
Ensure that a
proper utility
ground rod
is present &
connected.
Service entrance
ground rod
Service Entrance
Panel
GND GND
L2
L1
An input power ground wire from
the supply panel must be connected
to the drive.
A dedicated output ground wire
from the drive must be connected
to the motor (motor wires and ground
wires must be bundled together).
Pump
Motor
GND
GND
Use the service
entrance panel
ground ONLY.
DO NOT run ground wire separate.
Motor ground wire MUST be bundled with motor wires.
GND GND
Avoid multiple ground paths.
GND
GND
Pump
Motor
Pump
Motor
GND
Basic generator sizing for the Franklin Electric SubDrive/MonoDrive system is 1.5 times maximum input
watts consumed by the drive, rounded up to the next normal sized generator.
Recommended minimum generator sizes:
MonoDrive
1/2 hp = 2000 Watts (2 kW)
3/4 hp = 3000 Watts (3 kW)
1 hp = 3500 Watts (3.5 kW)
MonoDriveXT
1.5 hp = 4000 Watts (4 kW)
2 hp = 5000 Watts (5 kW)
SubDrive75 = 3500 Watts (3.5 kW)
SubDrive100 = 5700 Watts (6 kW)
SubDrive150 = 7000 Watts (7 kW)
SubDrive300 = 11000 Watts (11 kW)
SubDrive2W = 6000 Watts (6 kW)
Note: Not to be used on GFIC circuit or externally regulated generators.
Verify voltage, hertz and idle speed are appropriate to supply drive.
Generator Sizing for SubDrive/MonoDrive
Grounding/Generator Sizing

8
SubDrive75, SubDrive100, SubDrive150, MonoDrive & MonoDriveXT
MonoDrive MonoDriveXT SubDrive75 SubDrive100 SubDrive150
1/2 hp (motor) 1.5 hp (motor)* 3/4 hp (pump)* 1 hp (pump)* 1.5 hp (pump)*
1
2
3
4
1
2
3
4
1
2
3
4
O N
O N
O N
O N
1
2
3
4
1
2
3
4
O N
12
Black
Red
L2
From Power Source
L1
(Input)
ON
1234
SW1
L2
Sensor
Connection
Output to Motor
Configuration Switch SW1
See chart below for appropriate controller
setting. Reference the SubDrive/MonoDrive
Installation Manual or inside of lid for
more information.
Red Yel Blk
(Output)
Motor Cable
Power Supply from
Circuit Breaker
Feed the motor leads through
the large enclosure opening and
securely attach to the terminals
matching the lead colors.
Feed the pressure sensor wires
through the small enclosure
opening and securely attach to the
sensor terminals.
Feed the 230 V power leads through the large
enclosure opening and securely attach to the
terminals marked L1, GND and L2.
MonoDrive MonoDriveXT SubDrive75 SubDrive100 SubDrive150
3/4 hp (motor)* N/A 1 hp (pump) 1.5 hp (pump) 2 hp (pump)
MonoDrive MonoDriveXT SubDrive75 SubDrive100 SubDrive150
1 hp (motor) 2 hp (motor) 1.5 hp (pump) 2 hp (pump) 3 hp (pump)
To operate a different pump size, a Configuration Switch (SW1) must be positioned to select the correct pump rating.
Reference the chart below for appropriate Configuration Switch setting.
#3 Switch
Underload sensitivity selection
OFF Position - Normal(default) ON Position - Low
See SubDrive/MonoDrive Installation Manual for more information.
#4 Switch
Steady Flow - Control selection
OFF Position - Standard(default) ON Position - Steady Flow
See SubDrive/MonoDrive Installation Manual for more information.
Configuration Switch SW1
Wiring/Configuration-NEMA 1
*(default)

9
SubDrive75, SubDrive100, SubDrive150, MonoDrive & MonoDriveXT
Power Supply
From Circuit Breaker
BLACK
RED RED
YEL BLK
(BRN)
E4
(BLU)
GND
(OUTPUT)
E3
RV2
E5
E1
E2 E6
TO
L1 L2
(INPUT)
RED
YEL
INPUT
FILTER
TO
OUTPUT
FILTER
RV1
BLK
225505101 REVB GND
J2
J1
RV4
RV3
RV8
RV9
RV10
PRESSURE
SENSOR
SENSOR
213
3FAN
SW2
PRESSURE
SW1 2
4
14
R1
ADJUST
From Power Source
J1
L1 L2
(Input)
Output to Motor
Red Yel Blk
(Brn) (Blue) (Blk)
(Output)
J2
Feed the motor leads through
the large enclosure opening and
securely attach to the terminals
matching the lead colors to the
colors shown.
Feed the pressure sensor wires
through the small enclosure opening
and securely attach to the sensor
terminals.
Feed the 230 V power leads through
the large enclosure opening and
securely attach to the terminals
marked L1, GND and L2.
1 2 3 4
O
N
1 2 3 4
O
N
1 2 3 4
O
N
Configuration Switch SW1
See chart below for appropriate controller
setting. Reference the SubDrive/MonoDrive
Installation Manual or access cover for
more information.
BlkRed
Sensor Connection
PRESSURE
SENSOR
MonoDrive MonoDriveXT SubDrive75 SubDrive100 SubDrive150
1/2 hp (motor) 1.5 hp (motor)* 3/4 hp (pump)* 1 hp (pump)* 1.5 hp (pump)*
Power Supply
From Circuit Breaker
YEL BLK
(BRN) (BLU)
(OUTPUT)
L1 L2
(INPUT)
RED
PRESSURE
SENSOR
From Power Source
J1
L1 L2
(Input)
Output to Motor
Red Yel Blk
(Brn) (Blue) (Blk)
(Output)
J2
Feed the motor leads through
the large enclosure opening and
securely attach to the terminals
matching the lead colors to the
colors shown.
Feed the pressure sensor wires
through the small enclosure opening
and securely attach to the sensor
terminals.
Feed the 230 V power leads through
the large enclosure opening and
securely attach to the terminals
marked L1, GND and L2.
1 2 3 4
O
N
1 2 3 4
O
N
1 2 3 4
O
N
Configuration Switch SW1
See chart below for appropriate controller
setting. Reference the SubDrive/MonoDrive
Installation Manual or access cover for
more information.
BlkRed
Sensor Connection
PRESSURE
SENSOR
#3 Switch
Underload sensitivity selection
OFF Position - Normal(default) ON Position - Low
See SubDrive/MonoDrive Installation Manual for more information.
#4 Switch
Steady Flow - Control selection
OFF Position - Standard(default) ON Position - Steady Flow
See SubDrive/MonoDrive Installation Manual for more information.
1 2 3 4
O
N
1 2 3 4
O
N
SubDrive75, SubDrive100, SubDrive150, MonoDrive & MonoDriveXT
MonoDrive MonoDriveXT SubDrive75 SubDrive100 SubDrive150
3/4 hp (motor)* N/A 1 hp (pump) 1.5 hp (pump) 2 hp (pump)
MonoDrive MonoDriveXT SubDrive75 SubDrive100 SubDrive150
1 hp (motor) 2 hp (motor) 1.5 hp (pump) 2 hp (pump) 3 hp (pump)
Configuration Switch SW1
Wiring/Configuration-NEMA 4
To operate a different pump size, a Configuration Switch (SW1) must be positioned to select the correct pump rating.
Reference the chart below for appropriate Configuration Switch setting.
*(default)

10
PRESSURE
SENSOR SHUT-OFF
INT
FAN
INV
FAN
PFC
FAN
NO NO
COM
RELAY
SW2 SW1
O
N
Pressure sensor cable connection
Make sure the connection is securely made
Power Supply
From Circuit Breaker
PRESSURE
SENSOR SHUT-OFF
SW2 SW1
Output to Motor
Red Yel Blk
(Brn) (Blue) (Blk)
(Output)
BlkRed GrnWh
Sensor Connection
PRESSURE
SENSOR PRESSURE
SHUT-OFF
From Power Source
L1 L2
(Input)
Feed the motor leads through
the large enclosure opening and
securely attach to the terminals
matching the lead colors to the
colors shown.
Feed the pressure sensor wires
through the small enclosure opening
and securely attach to the sensor terminals.
Feed the 230 V power leads through
the large enclosure opening and
securely attach to the terminals
marked L1, GND and L2.
Configuration Switch SW1
See chart below for appropriate controller
setting. Reference the SubDrive/MonoDrive
Installation Manual or inside of lid for
more information.
O N
1
2
3
4
1
2
3
4
O N
#3 Switch
Underload sensitivity selection
OFF Position - Normal(default) ON Position - Low
See SubDrive/MonoDrive Installation Manual for more information.
#4 Switch
Steady Flow - Control selection
OFF Position - Standard ON Position - Steady Flow (default)
See SubDrive/MonoDrive Installation Manual for more information.
1
2
3
4
1
2
3
4
1
2
3
4
O N
O N
O N
1
2
3
4
1
2
3
4
1
2
3
4
O N
O N
O N
SubDrive300
3 hp (pump)
SubDrive300
5 hp (pump)
Configuration Switch SW1
SubDrive300
Wiring/Configuration-NEMA 4
To operate a different pump size, a Configuration Switch (SW1) must be positioned to select the correct pump rating.
Reference the chart below for appropriate Configuration Switch setting.
(default)