freebeat MORPH User manual

QUICK START
GUIDE
MORPH 2-IN-1 EBIKE

1. Position the package with the arrows on the side facing upward.
2. Raise up the top cover to unpack the package.
3. Verify that all items are present in the accessory box.
STEP 1. UNBOXING

Accessories Include……
INDOOR
WORKING STATION
Rear
Front
Accessories Box
User ManualQuick Start GuideFront light
Bell Battery Key × 2 Reflector Display
Allen Key
(M2.5/M3/M4/M5/M6)
Pedals
(L & R)
Charger
Screwdriver
(Flat Head)
Wrench
(M15)
15mm

1. Remove the nuts & washers from the front wheel axle
2. Attach the front wheel axle to the front fork.
3. Slide the front wheel washers onto the front wheel axle, and tightly
fasten the axle nuts to secure the front wheel.
4. Secure the front fender using M5&M6 screws and the rear fender
using M6 screws.
STEP 2. FRONT WHEEL ASSEMBLY

M6
M5
M5 M5

1. Bend down near the wheel to inspect for any squealing sound
coming from the brake disc and pads.
2. Loosen up the screw so the brake hub can move freely.
3. Adjust the clearance between the brake pad and disc, and
ensure that there is enough clearance between them.
4. Inspect the wheel again to identify the source of the squeaking
sound and check if the issue is resolved.
STEP 3. DISC BRAKE CALIBRATION

1. Ensure the stem is straightened up at a 90-degree angle.
2. Install the handlebar onto the stem.
3. Align and center the handlebar with the perfect angle facing you.
4. Fully tighten the screws on the side and top of handlebar.
STEP 4. HANDLEBAR ASSEMBLY
90°
M5
M5
M6

1. Use the M2.5 Allen key to loosen the screws holding the display.
2. Install the bracket onto the handlebar and securely tighten the screws
using the M2.5 Allen key.
3. Connect the blue and green female connectors to their corresponding
male connectors.
STEP 5. DISPLAY ASSEMBLY
M2.5

1. Install the rear light on the seat post, positioning it approximately
10mm (0.4 inches) below the saddle.
2. Release the saddle post clamp.
3. Adjust the saddle to your preferred "comfortable" riding height.
4. Securely close the saddle post clamp, making sure not to exceed the
minimum insert line.
STEP 6. REAR ASSEMBLY &
SADDLE ADJUSTMENT
B
A
C

1. Remove the sticker from the RIGHT crankset.
2. Install the RIGHT pedal onto the RIGHT crankset, following the
provided illustration. Rotate the pedal in a clockwise direction.
3. Use a wrench to securely tighten the RIGHT pedal.
4. Remove the sticker from the LEFT crankset.
5. Install the LEFT pedal onto the LEFT crankset, following the provided
illustration. Rotate the pedal in a counterclockwise direction.
6. Use a wrench to securely tighten the LEFT pedal.
STEP 7. PEDALS ASSEMBLY
R
L

R
L

1. Connect the wire of the front light.
2. Unscrew the front light M4 screws off the front light stands.
3. Install the front light onto the front light stands.
STEP 8. FRONT LIGHT ASSEMBLY
M4

STEP 9. BATTERY REMOVE/ASSEMBLY
1. Insert the battery key into the keyhole.
2. Rotate the battery key in a counter-clockwise direction to switch it to the
"UNLOCK" mode, as shown in the provided illustration.
3. Gently pull the top part of the battery out of the down tube.
4. Remove the battery from the down tube.
*If you want to install the battery, press the battery tight to the down tube,
and turn the battery key clockwise to "LOCK" mode.
Lock Unlock

1. Open the rubber cover on the charging socket.
A. Place the charger on a flat and secure surface. Connect the
output plug from the charger to the charging port located on
the side of the battery section.
2. Insert the input plug into a power outlet. Charging will begin, and
you will see the LED charge status light on the charger turn red.
3. Once the charging is complete, as indicated by the charging
indicator light turning green, start by unplugging the charger from
the wall outlet. Then, remove the charger's output plug from the
bike's charging port.
STEP 10. BATTERY CHARGING
Charging
Fully Charged
Red Light ON
Green Light ON

STEP 11. INDOOR WORKING STATION
FRONT
1. Align the screw holes located at the lower end of the bike rack's
main body with the corresponding holes on the bottom tube of the
bike frame. Insert the screws into the aligned holes.
2. Screw in the hex socket countersunk screw and use a tool to tighten
it securely.
3. Install and tighten the four corners of the product following the
sequence described above.
•The front station's bottom
tube is shorter than the rear
station's bottom tube, and
both were packed together
with the rear working station.
M6

STEP 11. INDOOR WORKING STATION
REAR
1. Take out the training unit body, main frame crossbar, and parts
package from the box.
2. Align the holes on the main frame crossbar with the
corresponding holes on the training unit body. Insert the carriage
bolt, place a flat washer, and tighten the cap nut.
3. Use an open-end wrench to securely tighten the cap nut. Make
sure the nut is tightened before using the training unit.

1. Peel off the proitective sticker from the display.
2. Long press the start button ( on your left hand side) to start your bike.
STEP 12. START YOUR BIKE
Start Button
Menu Button
Light Button
Minus Button
Plus Button
Total Mileage
Speed
Battery
Assist
To provide you with guidance on using the freebeat app,
please scan the QR code:

www.freebeatfit.com