FREESKY Rocky User manual
USER MANUAL
20" ROCKY ELECTRIC BIKE
YANSHAN Technology Co., LTD
Contact us if you experience issues relating to riding
Maintenance and safety, or errors/faults with your FREESKY e-bike
freeskycycle.com
611 Reyes Dr. City of Industry Walnut CA 91789
Freesky-ebike
@FREESKYEBike
Freesky club:FREESKYEBike/groups
909 892-8680 (available from 5 P.M. to 8 P.M.PST)
( )
Rocky
Mountain e-Bike
Words to Users
Thank you for choosing Freesky! In order to make it easier for
you to experience the product and be safe at riding, detailed
product, please read the manual carefully so that you can
Package List
Assembly
Start-Up Procedure
01
02
03
04
15
18
27
28
FAQS 29
Limited Warranty 30
Contents
1
Don't Ride Until You Read This:
（）
Package List
Carefully check package contents, if anything is missing or damaged, please contact Freesky custom-
support@freeskycycle.com
-
2
1x Charger 2x Pedals
2x Wrench
3x Allen Key Wrench 2x Keys
1×Electric Bike
1x User Manual
1x Saddle
1×Skewer 1×Fender
USER MANUAL
20" ROCKY ELECTRIC BIKE
3
Product Overview
LCD Display
Grip
Display Controls
Front Light
Stem
Front Fork
Tire
Pedals
Crankset
Chain
Motor
Saddle
Seat Post
4
Handlebar Assembly
12
3 4
5
Front Wheel Assembly
Figure 1
Figure 2
6
1.
Insert the axle into the wheel hub as shown. Add the Slim Spacer on the LEFT side
(Brake Disk) and the Wide Spacer on the RIGHT side.
2.
Insert the front wheel with the spacers in between the front fork on the bike.
Be sure to align the disk between the brake caliper as shown in Figure 2.
3.
Now on the outside add the washer and nut on each side and hand turn until snug.
4.
Using your wrench, tighten each side alternatively until snug (you might need
to secure the opposite nut slightly so the whole axle doesn’t turn)
5.
Now tighten each nut putting your weight into the wrench. Your front wheel is
now installed.
6.The Adjustment Nut needs to be very tight, be sure to retighten after your first
couple rides.
7
Front Light and Fender Assembly
12
34
8
Saddle Assembly
12
34
9
Seatpost Adjustment
frame beyond these markings, the seat post or frame may
-
may come loose and can result in loss of control, damage to
X
10
Front Fork Adjustment
riding on a rough road or trail smoother and more
The lockout lever(1), located on top of the right side of the
The preload adjustment knob(2),
1
2
11
1
2.
Warning: Incorrect installation will cause damage. Please read the instructions
and watch our videos if needed.
Identify the Left and Right markings on the pedals. They can only be installed in their
respective side.
a.L is for the Left Pedal and it goes on the Left Crank Arm.
b.R is for the Right pedal and it goes on the Right Crank Arm (Chain Side)
Pedals Assembly
12
3
4.
Sitting on your bike the pedals go on the Left and Right side respectively.
6.
The pedals need to be very tight, be sure to retighten after your first couple rides.
Keep the pedal Horizontal while hand screwing to get the thread started.
Then Use your 15mm wrench to tighten them.
5.
Both pedals tighten towards the front of the bike. The left pedal is reverse
threaded to allow this.
Use your 15mm
wrench to properly
tighten the pedals
Right Pedal /
Chain Side
Left Pedal /
Key Side
Both pedals tighten
towards the front
Rear
Front
13
1 2
34
14
Charge Your E-Bike
12
34
15
Start-Up Procedure
16
Display Details
1.Light
Table of contents
Other FREESKY Scooter manuals
