Fri-Jado LDR 8 s Auto Clean GAS User manual

LDR 8 s AC GAS
EN (Original Instruction) 9124665 / 2203
USER MANUAL
LDR 8 s Auto Clean GAS
WARNING
Read the instructions before using the machine.

LDR 8 s AC GAS
EN 2 / 32
Installation and service must be performed by a qualified installer, service agency or the gas
supplier.
Note to purchaser:
Obtain by consulting your local gas supplier the instructions to be followed in the event the user
smells gas. These instructions must be post in a prominent location.
KEEP THIS USER MANUAL IN A SAFE PLACE FOR FUTURE USE
© 2022 Fri-Jado B.V., Oud Gastel, The Netherlands.
We advise you to contact your supplier for the guarantee period and conditions. Further we refer to
our General Terms and Conditions for Sales and Delivery that are available upon request.
The manufacturer does not accept any liability for damage or injury caused by failing to adhere to
these regulations or by not observing the usual caution or care in actions, operation, maintenance
or repair activities, even if not explicitly described in this manual.
As a result of constant commitment to improvement, it may happen that your unit deviates in detail
from what is described in this manual. For this reason, the given instructions are only a guideline for
the installation, use, maintenance and repair of the unit referred to in this manual. This manual has
been composed with the utmost care. The manufacturer shall, however, not be held responsible for
any mistakes in this manual nor for any consequences thereof. The user is allowed to copy this
manual for own use. Further all rights are reserved and nothing in this manual may be reproduced
and/or made public in any way.
Modifications:
In case of unauthorized modifications in or on the unit, every liability on the part of the manufacturer
becomes null and void.
FOR YOUR SAFETY
Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or other appliance.
WARNING: Improper installation, adjustment,
alteration, service or maintenance can cause property
damage, injury or death. Read the installation, operation
and maintenance instructions thoroughly before installing
or servicing this equipment.

LDR 8 s AC GAS
EN 3 / 32
Empty page.

LDR 8 s AC GAS
EN 4 / 32
CONTENTS
1. INTRODUCTION ..............................................................................................................6
1.1 General.............................................................................................................................6
1.2 Identification of the unit.....................................................................................................6
1.3 Pictograms and symbols...................................................................................................6
1.4 Safety instructions ............................................................................................................7
1.4.1 General........................................................................................................................7
1.4.2 Moving.........................................................................................................................8
1.5 Hygiene ............................................................................................................................8
1.6 Service and technical support...........................................................................................8
1.7 Shutdown / Storage ..........................................................................................................8
1.8 Disposal............................................................................................................................8
2. DESCRIPTION OF THE UNIT..........................................................................................9
2.1 Technical description........................................................................................................9
2.2 Intended use.....................................................................................................................9
2.3 Accessories......................................................................................................................9
3. INSTALLATION AND FIRST USE ................................................................................. 10
3.1 Unpacking the unit..........................................................................................................10
3.2 Installation and positioning..............................................................................................10
3.3 First use..........................................................................................................................13
3.3.1 Metal odor .................................................................................................................13
4. OPERATION AND USE ................................................................................................. 14
4.1 Control Panel..................................................................................................................14
4.2 Switching-on the unit.......................................................................................................15
4.3 Loading the unit..............................................................................................................15
4.3.1 Loading the rotisserie using V-shape spits (accessory) .............................................15
4.3.2 Loading the rotisserie using meat baskets (accessory)..............................................15
4.4 Grilling time.....................................................................................................................16
4.5 Taking out the products ..................................................................................................16
4.5.1 Taking out the V-shape spit (accessory)....................................................................17
4.5.2 Taking out the meat basket (accessory) ....................................................................17
4.6 Emptying grease container / grease caddy (optional)......................................................17
4.7 Switching-off the unit.......................................................................................................17
5. OPERATE ...................................................................................................................... 18
5.1 Starting a program..........................................................................................................18
5.2 Reset burner controller ...................................................................................................18
5.3 Pre-heating.....................................................................................................................19
5.4 While cooking .................................................................................................................19
5.5 Adding extra time to the active program..........................................................................20

LDR 8 s AC GAS
EN 5 / 32
5.6 Interrupt a program.........................................................................................................20
5.7 Reset alarm signal..........................................................................................................20
5.8 Power down....................................................................................................................20
6. SETTINGS...................................................................................................................... 21
6.1 General...........................................................................................................................21
6.2 Overview main parameters (Manager)............................................................................21
6.3 Service Menu..................................................................................................................21
7. PROGRAM..................................................................................................................... 22
7.1 General...........................................................................................................................22
7.2 Adding programs ............................................................................................................22
7.3 Edit programs.................................................................................................................22
7.4 Deleting programs ..........................................................................................................23
8. CLEANING AND MAINTENANCE.................................................................................24
8.1 Maintenance schedule....................................................................................................24
8.2 Daily Cleaning.................................................................................................................24
8.3 Weekly Cleaning.............................................................................................................26
8.4 Additional Manual Cleaning ............................................................................................26
9. MALFUNCTIONS AND SERVICE..................................................................................27
9.1 Replace the mains cord..................................................................................................27
9.2 Replace the gas hose.....................................................................................................27
10. TECHNICAL SPECIFICATIONS .................................................................................... 28

LDR 8 s AC GAS
EN 6 / 32
1. INTRODUCTION
1.1 General
This manual is intended for the user of the LDR 8 s AC GAS (Large Deli Rotisserie on Gas with
cleaning feature). The features and controls are being described, along with directions for the safest
and most efficient use, in order to guarantee a long life of the unit.
All pictograms, symbols and drawings in this manual apply to all LDR 8 s AC GAS models.
1.2 Identification of the unit
The identification plate can be found on the outside of the machine, and contains the following data:
•Name of the supplier or the manufacturer
•Model
•Serial number
•Year of construction
•Country of destination
•Kind of gas
•Gas pressure
•Included gas power
•Mains voltage
•Frequency
•Electrical power consumption
1.3 Pictograms and symbols
In this manual, the following pictograms and symbols are used:
WARNING
Possible physical injury or serious damage to the unit, if the instructions are not
carefully followed.
WARNING
Hazardous electrical voltage.
WARNING
Danger of getting injured by hot surfaces.
WARNING
Risk of fire.
Suggestions and recommendations to simplify indicated actions.
Recycling symbol.
Direction of view symbol.

LDR 8 s AC GAS
EN 7 / 32
1.4 Safety instructions
WARNING
The top cover (in particular the flue tube) and the outside of the unit can be very
hot.
WARNING
Do not put any objects on the equipment as this may cause fire. Keep all openings
free from obstacles.
WARNING
Keep the opening between the equipment and the table surface free from obstacles
in order to ensure good ventilation in the electrical compartment.
WARNING
Risk of slippery floor: Spills may cause slippery surfaces, clean-up promptly.
WARNING
See installation instructions for grounding requirements.
WARNING
Always use the brakes on both front wheels:
1.4.1 General
The user of the unit will be fully responsible for abiding the locally prevailing safety- rules and
regulations.
The unit may be operated by qualified and authorized persons only. Anyone working on or with this
unit must be familiar with the contents of this manual and carefully follow all guidelines and
instructions. Never change the order of the steps to be performed. The management must instruct
the personnel on the basis of this manual and follow all instructions and regulations.
The pictograms, labels, instructions and warning signs attached to the unit, are part of the safety
measures. They may never be covered or removed, and have to be clearly visible during the entire
lifetime of the unit.
Immediately repair or replace damaged or illegible pictograms, warnings and instructions.
•To avoid short-circuiting, never clean the unit using a water hose. For cleaning instructions, see
section 8.
•During the grilling process, the unit can get very hot.
•When the door is opened the rotor stops and the heater is de-energized.
•The unit must be cleaned daily after use to ensure proper functioning and prevent fire hazard
(over heating).
•The fat collecting container must be emptied regularly, to prevent overflow.
•This appliance can be used by children aged from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance in a safe way and understand
the hazards involved.
•Children shall not play with the appliance.

LDR 8 s AC GAS
EN 8 / 32
•Cleaning and user maintenance shall not be made by children without supervision.
1.4.2 Moving
When moving the unit:
•Before moving the unit, first switch off the mains voltage by pulling the plug from the wall socket
and empty the fat collecting container. After that, cool-down the unit for at least ten minutes.
•Disconnect the water supply and drain. Disconnect the Gas supply.
•The units equipped with wheels are not suited to pass ledges or obstacles higher than 10 mm
(0.4 inch).
•When moving the unit, always push at the center of the unit. Never on top. Never at the bottom.
•Make sure that the wheels can move freely, so they never touch the gas hose and/or the power
lead.
1.5 Hygiene
The quality of a fresh product always depends on hygiene. Especially grilling products. With the
risk of salmonella contamination –especially for chicken products –you must make sure that grilled
products can never be mixed with uncooked products. Also contact between grilled products and
hands or tools that have been in contact with raw chicken meat, must be avoided at all times.
Hands or tools that have been in contact with raw chicken meat, must be cleaned thoroughly.
1.6 Service and technical support
The electrical schematics of your unit is included. In case of malfunctions you can contact your
dealer/service agent. Make sure you have the following data available:
•Model.
•Serial number.
This data can be found on the identification plate.
1.7 Shutdown / Storage
If the unit will not be used temporarily, follow these instructions:
•Disconnect power supply.
•Disconnect water supply.
•Shut off external gas supply.
•Clean the unit thoroughly.
•Wrap the unit from getting dusty.
•Store, when applicable, the unit in a dry, non-condensing environment.
1.8 Disposal
Dispose of the machine,any components or lubricants removed from it safely in accordance
with all local and national safety and environment requirements.

LDR 8 s AC GAS
EN 9 / 32
2. Description of the unit
2.1 Technical description
Heating takes place by means of gas that is burnt in a heat exchanger placed in the ceiling. A fan
mixes the gas and air, which mixture is ignited by means of an automatic ignition. The modulated
gas combustion takes place in the inner part of the heat exchanger and is therefore not visible. The
flue gasses are discharged through a flue tube at the top or side off the unit. Fans ensures an equally
divided heat. In order to maintain the set temperature the heat exchanger is modulating during the
grilling process.
During the entire process, the interior of the unit will be illuminated by halogen lamps.
The unit control keeps the temperature inside the unit fixed to level set by the operator.
The rotor is being wheeled by a maintenance-free motor and gearbox. The hardened glass panes
are equipped with a heat reflecting layer to keep the heat inside the grill.
The plating of the unit is made of stainless steel. The product contact parts are made of stainless
steel AISI 304. The mains cable is provided with a plug.
Refer to the data plate for the applicable gas system.
2.2 Intended use
The unit has been designed for grilling meat products and has a semi self-cleaning feature. Any
other use will not be regarded as intended use.
The manufacturer accepts no liability whatsoever for loss or injury caused by failing to strictly adhere
to the safety guidelines and instructions in this manual or due to carelessness during installation,
use, maintenance and repair of the unit referred to in this manual and any of its accessories.
Use the unit in perfect technical condition only.
2.3 Accessories
Your unit contains the following standard accessories:
•Cleaning cartridge holder.
•User manual.
For optional accessories see www.frijado.com.

LDR 8 s AC GAS
EN 10 / 32
3. INSTALLATION AND FIRST USE
All packing materials used for this unit are suited for recycling.
After unpacking, check the state of the unit. In case of damage, store the packing material, and
contact the transporter within fifteen working days after receiving the goods.
3.1 Unpacking the unit
1. Unpack the unit as initiated on the unpacking instruction on the packaging.
2. Remove all remaining packing materials from the unit.
3. Remove the protective foil from the metal parts.
4. Take off the standard accessories.
3.2 Installation and positioning
WARNING
Electric chock hazard. Grounding instructions: only connect the appliance to an
alternating current provided by a grounded wall socket, with a mains voltage in
accordance with the information indicated on the data plate of the appliance.
It is the consumer's responsibility to make sure the electrical installation conforms
with current national and local codes and wiring regulations.
Do not use a multi plug or extension cord. Such can result in fire, electrical shock, or
other personal injury.
Failure to follow these instructions can result in death or serious injury.
WARNING
DO NOT USE THIS GRILL WITH ANY GAS OTHER THAN THE ONE SHOWN ON
THE MODEL RATING PLATE.
WARNING
Position the unit on a flat and horizontal surface. A temporally inclined plane of
maximum 5° is allowed.
WARNING
Install the equipment in a sufficiently ventilated room in order to prevent
concentrations of harmful substances in that room.
WARNING
Always install the equipment under a ventilated cooker hood.
WARNING
The equipment is not suitable for direct connection to an air duct.
WARNING
The wall socket and the gas provisions are to be installed by a registered installer
in accordance with the current national and local regulations.

LDR 8 s AC GAS
EN 11 / 32
WARNING
Settings on the gas equipment are secured by the manufacturer and should under
no circumstances be broken by the installer. Settings must not be changed.
WARNING
Do not store or use gasoline or other flammable vapors or liquids in the vicinity of
the appliance.
Positioning:
•The user must have sufficient freedom of movement to properly operate the unit.
•The ambient temperature of the unit must be between 10 and 30 °C (50 and 86 °F).
•Use proper lifting–and transport tools to move the unit.
•Place the unit, using a spirit level, flat on a solid surface. Mind the weight of the unit!
•The minimum free distance must be at least 100 mm (4 inch).
•Keep a distance of at least 500 mm (20 inch) of free space above the unit. Placing the unit under
a hood is required.
•The products inside the unit must be clearly visible.
•Keep children away from the operating side of the unit.
•During grilling, the glass panes will get very hot. While positioning, keep the unit out of children’s
reach.
•The gas connection has an outside diameter of ½ inch. The gas connection must be mounted
by a registered installer.
•The oven must be installed so that the flow of combustion and ventilation air will not be
obstructed. Make sure there is an adequate supply of air in the room to allow for that required
combustion of gas of the oven chamber.
•Keep the space around the bottom and the ventilation opening in the top of the unit free from
obstacles to guarantee a good air flow in the electrical compartment and combustion chamber.
•Appliance is for use only with the specific legs or casters specified by the manufacturer.
•In case of a wheeled unit, the floor must be flat and leveled.
38 ½ IN (980 mm)

LDR 8 s AC GAS
EN 12 / 32
Installation:
•North American units must be installed conform local codes, or in the absence of local codes,
with the National Fuel Gas Code, ANSI Z223.1/NFPA 54, or the Natural Gas and Propane
Installation Code, CSA B149.1, as applicable, including:
i) The appliance and its individualshutoff valve must be disconnected from the gas supply piping
system during any pressure testing of that system at test pressures in excess of ½ psi (3.5 kPa).
ii) The appliance must be isolated from the gas supply piping system by closing its individual
manual shutoff valve during any pressure testing of the gas supply piping system at test
pressures equal to or less than ½ psi (3.5 kPa).
•North American units must when installed be electrically grounded in accordance with local
codes, or in the absence of local codes, with the National Electric Code, NFPA 70, or the
Canadian Electrical Code, CSA C22.2, as applicable.
•North American units equipped with casters must be installed with connectors that comply with
the Standard for Connectors for Movable Gas Appliances, ANSI Z21.69 • CSA 6.16. This
connection must include a quick disconnect device that complies with the Standard for Quick
Disconnect Devices for Use With Gas Fuel, ANSI Z21.41 • CSA 6.9.
•Adequate means must be provided to limit the movement of the appliance without depending on
the connector and quick-disconnect device or its associated piping to limit the appliance
movement. The restraining device should be attached to the appliance tether bracket.
restraining suggestion
•A water connection with an aerated valve with a ¾ inch thread connection, with a minimum
continuous flow rate of 15 liters / min, must be available near the unit. The water pressure must
be between 200 and 500 kPa (2 and 5 bar), preferably at least 300 kPa (3 bar). Refer to the
Installation Manual.
•Use the water hose supplied with the machine.
•An open drainage with a diameter of at least 40 mm (1.6 inch) must be available near the unit.
•The unit has amains plug, and must beconnected to a wall socket with the proper mainsvoltage.
The wall socket must be mounted by a certified electrician.
•A Gas supply with a 1/2 inch NPT connection must be available near the unit.
•Use the GAS pipe supplied with the machine.

LDR 8 s AC GAS
EN 13 / 32
3.3 First use
When using the unit for the first time, clean the interior thoroughly with soap suds and heat up the
unit, see section 3.3.1. After commissioning discoloration of the cooking/grilling area can occur.
➊➋
➌
➍➎
3.3.1 Metal odor
To remove the metal odor that will appear at first use, the unit must be heated at the maximum
temperature (220°C/428°F) for at least half an hour.
1. Tap on the control screen and switch-on the unit.
2. Press to display the recipe screen.
3. Create a new program containing ONE step of maximum temperature and a duration
of at least 30 minutes (See section 7).
4. Select the new program and press to start (See section 5).
5. Allow the unit to fully execute the program.
The unit is now ready for use.

LDR 8 s AC GAS
EN 14 / 32
4. OPERATION AND USE
4.1 Control Panel
Main Functions:
ON / OFF
Recipes
Wipe/clean touch screen (during countdown)
Clean Rotisserie
Home screen
Language
Help function
Tap or swipe to select function or activate additional screen
Step Back (when shown at upper left corner)

LDR 8 s AC GAS
EN 15 / 32
4.2 Switching-on the unit
4.3 Loading the unit
When the door is open press the rotor button to activate the rotor. This allow easy loading or
unloading the products.
Whilst loading the unit, make sure that the rotor gets evenly loaded, so that the mass of the products
is evenly spread over de rotor, causing an equal balance. Do not allow empty meat forks, meat
baskets and chicken racks etc. in the grilling process.
4.3.1 Loading the rotisserie using V-shape spits (accessory)
If you are using V-shape spits act as follows:
•Place the skewer into the small outside hole on the rotor end plate on your left (as you face the
oven). The back of the V-shape spit should be pointing towards you.
•Fit the other end on the spit into the small corresponding holes on the rotor end plate on your
right (as you face the oven).
•Make sure the spit is level. If spit is not level make sure you are using the correct holes on the
rotor end plates.
4.3.2 Loading the rotisserie using meat baskets (accessory)
If you are using meat baskets, act as follows:

LDR 8 s AC GAS
EN 16 / 32
•Whilst loading the unit with meat baskets, you must see to it, that the rotor gets evenly loaded,
so that the mass of the products is evenly spread over de rotor, causing an equal balance.
•Also see to it that no meat parts are sticking out of the baskets.
4.4 Grilling time
Grilling time depends on a number of factors:
•The ambient temperature and draft in the direct vicinity of the unit.
•Grilling temperature.
•The initial product temperature.
•The sort of meat (fat or lean) and with or without additives.
•The mass and shape of the product.
•The total amount of meat to be grilled in one grilling cycle.
•The end result.
Seasonings
The use of herbs and seasoning adds a specific twist to every meal. Using them right
is of great importance for the end result.
Guidelines for seasoning are:
•Preferably use the special chicken and meat seasonings of the supplier of the Fri-
Jado Grill. There are special seasoning mixtures for poultry, lamb, pork, large
meat, game and fish.
•Season the products to be grilled when dry.
•Season the products 90 minutes before grilling at the most to prevent the spices
from abstracting too much fluid from the meat.
•Do not add oil or grease while grilling.
•Season chicken on the inside and on the outside.
4.5 Taking out the products
WARNING
After the grilling, the interior of the unit and the glass panes are very hot.
Always use oven gloves when taking out the meat forks or other accessories.

LDR 8 s AC GAS
EN 17 / 32
4.5.1 Taking out the V-shape spit (accessory)
When taking out the V-shape spit, it is best to act as follows:
1. Hold the V-shape spit firmly.
2. Slightly lift the end with the grips and shift the spit into the direction of its point.
This releases the spit.
3. Take the spit at its other end and take it out of the unit.
4. Remove the products from the spit.
Refer to the You-Tube movie: “Fri-Jado instruction for unloading chicken from a
rotisserie”.
4.5.2 Taking out the meat basket (accessory)
When taking out the meat basket from the LDR it is best to act as follows:
1. Slightly lift both ends of the meat basket.
2. Move the basket towards either the left or right hand side of the unit. This action
unlocks one end of the basket.
3. Move the unlocked end towards you and take out the basket from the unit.
Depending on the number of prepared products you may have to empty the baskets before they can
be removed.
4.6 Emptying grease container / grease caddy (optional)
WARNING
Check the grease container / caddy after each cooking process and empty already
when about half full to avoid overflowing.
WARNING
Grease will be hot immediately after cooking. Allow grease to cool or use extreme
caution and wear insulated gloves or safety mitts.
1. Take the grease container / caddy out.
2. Empty the container / caddy.
3. Place the (emptied) container / caddy back.
4.7 Switching-off the unit

LDR 8 s AC GAS
EN 18 / 32
5. OPERATE
5.1 Starting a program
1. Press .
2. Select the required program. The total duration of the
program is shown in minutes next to the program name.
3. Press .
5.2 Reset burner controller
Message “Burner failed, check gas supply and reset burner”
appears on screen when the burner is not in operation when
needed.
1. Reset the burner by pressing the Reset button on screen.
The unit will now attempt a re-start.
After 3 repeated failures the burner goes into error mode and
the message “Gas burner failure. Call tech support”appears.
2. Call technical support to assist.
3. Press the OK button to accept the message.

LDR 8 s AC GAS
EN 19 / 32
5.3 Pre-heating
When the pre-heat function is activated (at manager menu), the
unit will start this function after selecting a program.
The screen will display the actual temperature (at the top).
Tap on the temperature box to see the set pre-heat temperature
(approx. 5 sec.).
When the set temperature is reached, the screen will show:
“Preheat done. Waiting for oven to be loaded” and a sound is
activated.
Load the rotisserie and press .
5.4 While cooking
WARNING
Opening the door during a grilling program or a cleaning program causes the unit to
stop and a warning is shown.
The unit will continue when the door is closed and pressed.
During the cooking process, the displayshows a graph with the:
•planned trajectory (dark blue time line).
•processed trajectory (light blue time line).
•program steps (white stripe).
•and the set temperature (at the top).
In the center the graph,the program name, current function and
remaining time are shown.
In the bottom of the screen the process steps are given.
The screen will display the set temperature (at the top).
Tap on the temperature box to see the actual temperature
(approx. 5 sec.).
When ‘cook correction’ is switched-on the remaining time will
be automatically adjusted.

LDR 8 s AC GAS
EN 20 / 32
5.5 Adding extra time to the active program
During the process extra time can be added (when activated in
the manager menu), by following the next steps:
1. Press .
2. Set extra time.
3. Select to save setting.
The display now shows the extra time, which will be added to
the last cooking step. The screen always shows the total
amount of extra time.
5.6 Interrupt a program
Interrupt temporarily:
1. Press .
2. Press to resume the program.
Interrupt definitely:
Press and press on Cancel Receipt.
5.7 Reset alarm signal
When an alarm signal has been set, a message will occur. Press to return to the main menu.
5.8 Power down
If no program is active and no key is touched within the next 60 minutes the unit will switch-off
automatically.
This option can be both switched-off or adjusted by a service engineer.