Fri-Jado CSD 180 User manual

CSD 180
EU EN (Original Instruction) 9123529 / 2305
USER MANUAL ‒EU version
Convenience Store Displayer 180
WARNING
Read the instructions before using the machine.

CSD 180
EU 2/20
KEEP THIS USER MANUAL FOR FUTURE USE!
© 2023 Fri-Jado B.V., Oud Gastel, The Netherlands.
We advise you to contact your supplier for the guarantee period and conditions. Further we refer to
our General Terms and Conditions for Sales and Delivery that are available upon request.
The manufacturer does not accept any liability for damage or injury caused by failing to adhere to
these regulations or by not observing the usual caution or care in actions, operation, maintenance
or repair activities, even if not explicitly described in this manual.
As a result of constant commitment to improvement, it may happen that your unit deviates in detail
from what is described in this manual. For this reason, the given instructions are only a guideline for
the installation, use, maintenance and repair of the unit referred to in this manual.
This manual has been composed with the utmost care. The manufacturer shall, however, not be
held responsible for any mistakes in this manual nor for any consequences thereof.
The user is allowed to copy this manual for own use. Further all rights are reserved and nothing in
this manual may be reproduced and/or made public in any way.
Modifications:
In case of unauthorized modifications in or on the unit, every liability on the part of the manufacturer
becomes null and void.

CSD 180
EU 3/20
CONTENTS
1. INTRODUCTION..............................................................................................................4
1.1 General.............................................................................................................................4
1.2 Identification of the unit.....................................................................................................4
1.3 Pictograms and symbols...................................................................................................4
1.4 Safety instructions ............................................................................................................5
1.4.1 General........................................................................................................................5
1.4.2 Moving (when applicable)............................................................................................6
1.4.3 Outdoor use restrictions...............................................................................................6
1.5 Hygiene ............................................................................................................................6
1.6 Service and technical support...........................................................................................6
1.7 Storage.............................................................................................................................7
1.8 Disposal............................................................................................................................7
2. DESCRIPTION OF THE UNIT..........................................................................................8
2.1 Technical description........................................................................................................8
2.2 Intended use.....................................................................................................................8
2.3 Accessories......................................................................................................................8
2.4 Parts.................................................................................................................................9
2.4.1 Overview of the unit.....................................................................................................9
3. INSTALLATION AND FIRST USE ................................................................................. 10
3.1 Unpacking the unit..........................................................................................................10
3.2 Installation and positioning..............................................................................................10
3.3 Warm through.................................................................................................................11
3.4 Move...............................................................................................................................11
4. OPERATION AND USE ................................................................................................. 12
4.1 Operating........................................................................................................................12
4.2 Set the temperature........................................................................................................12
4.3 Load product...................................................................................................................13
4.4 Fill the water tray ............................................................................................................13
5. CLEANING AND MAINTENANCE................................................................................. 14
5.1 Maintenance schedule....................................................................................................14
6. MALFUNCTIONS AND SERVICE..................................................................................15
6.1 Replace the lamp............................................................................................................16
6.2 Replace the mains cord..................................................................................................16
7. TECHNICAL SPECIFICATIONS ....................................................................................17

CSD 180
EU 4/20
1. INTRODUCTION
1.1 General
This manual is intended for the user of the CSD180 (ConvenienceStoreDisplayer 180). The features
and controls are being described, along with directions for the safest and most efficient use, in order
to guarantee a long life of the unit.
All pictograms, symbols and drawings in this manual apply to all available CSD 180 (EU) models.
1.2 Identification of the unit
The identification plate can be found on the outside of the machine, and contains the following data:
•Name of the supplier or the manufacturer.
•Model.
•Serial number.
•Year of construction.
•Voltage.
•Frequency.
•Power consumption.
1.3 Pictograms and symbols
In this manual, the following pictograms and symbols are used:
WARNING
Possible physical injury or serious damage to the unit, if the instructions are not
carefully followed.
WARNING
Hazardous electrical voltage.
WARNING
Danger of getting injured by hot surfaces.
SAFETY
Wear safety gloves for installation and dismantling.
Suggestions and recommendations to simplify indicated actions.
Recycling symbol.

CSD 180
EU 5/20
1.4 Safety instructions
WARNING
The outside and shelves of the unit can be very hot.
WARNING
The maximum load on top of the unit may never exceed 10 kg.
WARNING
See installation instructions for grounding requirements.
1.4.1 General
The user of the unit will be fully responsible for abiding the locally prevailing safety- rules and
regulations.
The unit may be operated by qualified and authorized persons only. Anyone working on or with this
unit must be familiar with the contents of this manual and carefully follow all guidelines and
instructions. Never change the order of the steps to be performed. The management must instruct
the personnel on the basis of this manual and follow all instructions and regulations.
The pictograms, labels, instructions and warning signs attached to the unit, are part of the safety
measures. They may never be covered or removed, and have to be clearly visible during the entire
lifetime of the unit.
Immediately repair or replace damaged or illegible pictograms, warnings and instructions.
•To avoid short-circuiting, never clean the unit using a water hose. For cleaning instructions,
see section 5.
•The shelves, glass and back of the hot unit can get hot.
•The unit must be cleaned regularly to ensure proper functioning.
•Do not store explosive substances such as aerosol cans with flammable propellant in this
appliance.
•This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if they
have been given supervision or instruction concerning use of the appliance in a safe way and
understand the hazards involved.
•Children shall not play with the appliance.
•Cleaning and user maintenance shall not be performed by children without supervision.

CSD 180
EU 6/20
1.4.2 Moving (when applicable)
When moving the unit:
•Before moving the unit, first switch off the mains voltage by pulling the plug from the wall
socket.
•Remove pans containing a liquid product from the unit.
•Always keep the unit in upright position.
•Make sure that the wheels can move freely, so they never touch the power
lead.
1.4.3 Outdoor use restrictions
WARNING
To avoid short-circuiting, the units may not be used outdoors or in a rainy or very
moist environment.
1.5 Hygiene
WARNING
Immediately remove products in damaged packaging from the equipment and
destroy the products. Clean all components that have comein contact with products
from damaged packaging.
The quality of a fresh product alwaysdepends onhygiene. It is essential that products are packaged
immediately after preparation. Prevent fresh raw vegetables or already prepared, cooled products
from coming into contact with raw meat products to avoid transmitting salmonella. First thoroughly
clean hands and / or tools that have touched raw meat.
For hot products, the core temperature of the products at packaging should at least be 85ºC.
Be aware that high humidity levels may encourage the growth of biological organisms in the
environment.
Refer to the cleaning instructions of section 5.
1.6 Service and technical support
The electrical schematics of your unit is included. In case of malfunctions you can contact your
dealer / service agent. Make sure you have the following data available:
•Model.
•Serial number.
This data can be found on the identification plate.

CSD 180
EU 7/20
1.7 Storage
If the unit will not be used temporarily, and will be stored, follow these instructions:
•Clean the unit thoroughly.
•Wrap the unit from getting dusty.
•Store the unit in a dry, non-condensing environment.
•Ensure good ventilation.
•FS and SS Humidified models: empty water tray.
1.8 Disposal
Dispose of the machine, any components or lubricants removed from it safely in
accordance with all local and national safety and environment requirements.

CSD 180
EU 8/20
2. DESCRIPTION OF THE UNIT
2.1 Technical description
The display warmer keeps the products warm by means of a warm airflow with a high humidity level.
The fan in the display ensures an even distribution of heat. The products maintain the required
quality in the display for a maximum of three hours.
The display hasglass on three sides andthe rear side has areflecting rear window, allowing optimum
presentation of the products
2.2 Intended use
WARNING
The display-warmer is exclusively designed for keeping warm products warm and for
presenting them.
Any other use shall be considered to be not in conformity with the intended use. The manufacturer
accepts no liability whatsoever with regard to loss or injury that may be the consequence hereof.
The unit was built in accordance with European Guidelines and standards as specified in the CE
declaration delivered with your unit. Use the unit solely in technically perfect condition and in
conformity with the intended use described above.
2.3 Accessories
Your unit contains the following standard accessories:
•User manual.
For optional accessories contact [e-mail].

CSD 180
EU 9/20
2.4 Parts
2.4.1 Overview of the unit
A1 On / Off switch.
A2 Temperature display.
A3 Temperature setting.
A4 Water tray rear side.
A5 Door rear side.
A6 Lighting beneath plateaus.
A7 Display / slide holder and lighting of upper
plateau.
A8 Plateau (3 pieces).
A9 Flap window customer side (3 pieces).
A10 Covering panel of water tray.
A11 Water tray.
A4
A6
A5
A7
A8
A9
A10
4
5
6
1
2
3
A3
A1
A2
A11

CSD 180
EU 10/20
3. INSTALLATION AND FIRST USE
All packing materials used for this unit are suited for recycling.
Before and during unpacking, check the state of the unit. In case of damage, store the packing
material, and contact the transporter within fifteen working days after receiving the goods.
3.1 Unpacking the unit
1. Remove all parts from the unit.
2. Remove the foil from all metal parts.
3. Remove all packaging materials from the unit.
4. Check the unit for damage.
5. Make sure that all parts that belong to the model you have ordered are present.
6. Read the manual before proceeding.
If any parts are missing or damaged, contact your supplier.
3.2 Installation and positioning
WARNING
There should be at least 100 mm clearance between the sides and other equipment
or walls.
Position the unit flatly on a sufficiently sturdy base using a spirit level. Here take
the weight of the unit into account.
Follow the procedure below when storing a unit that will not be used for some
time:
1. Thoroughly clean the unit.
2. Pack the unit dustproof.
3. Store the unit in a dry place.
Positioning
Find a suitable place for the unit.
Points of interest:
•The products in the unit must be well visible.
•There must be sufficient room to operate and maintain the unit.
•Make sure that the unit is accessible for maintenance and service activities.
•Be sure that the environmental temperature is not less than 20°C and not more than 30°C.
•In connection with the danger of short circuit the unit is not suited for use in a rainy or very
moist environment.

CSD 180
EU 11/20
Installation
1. Clean the inside, the removable parts and the accessories thoroughly with soapsuds before
putting the unit into use.
2. Aftercleaning,wipetheunitwithaclothmoistenedwithcleanwatertoremovesoapsudsresidues
and then dry the entire unit.
3. Attach all (optional) parts and / or accessories.
4. Insert the plug into the socket.
5. Fill the water tray with clean cold water. Preferably use softened water.
The presentation plateaus have different dimensions. A mark has been provided
for easy placement. The bottom plateau has been marked with one groove, the
middle plateau has two grooves and the top plateau three.
The water tray can be placed on the customer side as well as on the service side.
Install slide:
Insert a slide if the unit has been provided with a
slide holder.
WARNING
Remove the plug from the outlet.
1. Loosen the 7 screws in the ceiling around
the lighting, but do not remove them.
2. Carefully push against the slide holder until
the lighting module cannot slide in further.
3. Remove the two transparent plastic plates
(A) from the slide holder and take them out
via the bottom of the unit.
4. Place the new slide (B) between the plastic
plates (A) and go through the steps in
reverse order.
3.3 Warm through
Let the unit warm through for at least half an hour at the highest temperature
setting to allow the metal odour that exudes from it when it is new to burn off.
3.4 Move
Before moving the unit:
1. Switch off the unit.
2. Remove the plug from the outlet.
3. Let the unit cool off for fifteen minutes.
4. Empty the water tray.
A
B

CSD 180
EU 12/20
4. OPERATION AND USE
WARNING
Especially an empty water tray and the lamp holder can become very hot.
The windows can mist up during the heating period: the condensation will disappear
after approximately 15 minutes.
4.1 Operating
Switch on:
1. Switch on the equipment using switch A1. The
lighting, the heating and the fans are activated.
2. Set the required temperature. See section 4.2.
3. Preheat the display to the required temperature
for approximately 15 minutes.
Display A2 shows the temperature in the display during
use.
Switch off:
1. Switch off the unit using switch A1.
4.2 Set the temperature
WARNING
Meat products should be kept in the
display-warmer at a minimum
temperature of 70°C; only then you can
be sure that the product temperature is
above 65°C.
1. Set button A3 to the required position (1-6). See
the table.
Temperature setting
A3
Temperature
(°C)
1
approx. 22
2
approx. 35
3
approx. 48
4
approx. 61
5
approx. 74
6
approx. 87
When the temperature in the display is equal to the set
temperature, the heating element will switch off; the
other components remain in operation.
A1
A2
4
5
6
1
2
3
A3

CSD 180
EU 13/20
4.3 Load product
WARNING
Only place warm products. Make sure with packaged products that the packaging
material is suitable for a temperature of 100°C.
4.4 Fill the water tray
Regularly check the water level in the water tray and fill
up with warm water if necessary. The water use is about
1.2 litre per hour.
Pull out the water tray before filling it. The water tray can
be filled both on the service side and on the customer
side.
On the customer side you can access the water tray by
opening the flap at the bottom side upward.

CSD 180
EU 14/20
5. CLEANING AND MAINTENANCE
WARNING
Remove the plug from the wall socket when carrying out maintenance and
cleaning activities.
Do not clean the unit using a water hose.
WARNING
The heating element above the water tray can still be hot!
Do not clean the unit using steel wool.
Fri-Jado Clean may in some cases irritate a sensitive skin. Wear rubber gloves
when using it.
Follow the instructions on the label of Fri-Jado Clean.
In view of hygiene and an optimal condition of the unit it is important to adhere to a
fixed cleaning pattern from the very beginning.
It is best to remove meat residual and grease shortly after using the unit, while it is
lukewarm. Optimum cleaning results are achieved by using Fri-Jado Clean.
5.1 Maintenance schedule
Item
Action
Cleaning
frequency
Interior and
exterior
•Switch off the unit.
•Take the products out of the unit.
•Allow the equipment to cool off.
•Clean the interior with hot soapsuds or Fri-Jado Clean.
•After cleaning, dry the interior with aclean cloth. Make sure
no traces of cleaning agent are left behind.
Daily
Glass
•Clean the glass parts with hot water and a cleaning agent
for glass.
Daily
Presentation
plateaus
•Clean the interior with hot soapsuds or Fri-Jado Clean.
Daily
Water tray
•Clean the water tray with hot soapsuds or Fri-Jado Clean.
•Remove any scaling from the water using warm water and
vinegar.
Weekly

CSD 180
EU 15/20
6. MALFUNCTIONS AND SERVICE
Before you consult your dealer or the service agency when there is a fault, you can check the
following points yourself:
•Is the power supply OK? Check the fuses and the earth leakage switch in the meter
cupboard.
•Are all the switches in the correct position?
Item
Malfunction
Possible action
Unit
Does not function.
•Is the plug in the outlet?
•Is the power supply OK? Check the
fuses and the earth leakage switch in
the meter cupboard.
•Are all switches in the correct position?
Unit
The set temperature is not
reached within half an hour.
•Close all windows.
Unit
The temperature rises too much.
•Check the set temperature.
•Switch off the unit.
•Remove the plug from the outlet.
•Contact your supplier / service agency.
Lamp
A lamp is defective.
•Replace, see section 6.1.
Mains cord
Damaged.
•Replace, see section 6.2.
Window
Damaged.
•Replace, contact your supplier /
service agency.

CSD 180
EU 16/20
6.1 Replace the lamp
WARNING
Let the unit cool off for at least half an hour with all windows open.
The lamps are found in the upper cover and beneath
the presentation plateaus.
1. Remove the plug from the outlet.
2. Open all windows and let the unit cool off for at
least half an hour.
For the lamp in the upper cover:
3. Loosen the 7 screws in the ceiling around the
lighting, but do not remove them.
4. Carefully push against the slide holder until the
lighting module cannot slide in further.
5. Remove the two transparent plastic plates (A)
from the slide holder and take them out via the
bottom of the unit.
6. Remove the neon lamp by pulling it lengthwise
out of the holder. Do this carefully to avoid
breaking.
7. Replace the lamp by one of the same type and
go through the steps you have just carried out in
reverse order.
For the lamp beneath the presentation plateau:
3. Dismount the neon lamp by turning it a quarter
turn.
4. Replace the lamp by one of the same type.
6.2 Replace the mains cord
WARNING
Hazardous electrical voltage.
If the power cord is damaged it must be replaced, contact your supplier or service agent.
A

CSD 180
EU 17/20
7. TECHNICAL SPECIFICATIONS
WARNING
See the identification plate for the correct specifications of the unit. The electrical
installation data may vary between different countries.
Model
CSD 180
Approved for
EU
Width
728 mm
Depth
576 mm
Height
877 mm
Weight Net Approx.
63 kg
Voltage
1N~230V
Frequency
50 / 60 Hz
Max. rated current
11,3 A
Power to be supplied
2610 W
Plug
two-pole earthed plug
Cable length
2,4 m
Sound pressure
<70 dB(A)
Water tray –Max. volume
8 L
Water tray –Max. water use per hour
1,2 L

CSD 180
EU 18/20
Notes:

CSD 180
EU 19/20
Notes:

CSD 180
EU 20/20
Fri-Jado B.V.
Blauwhekken 2
4751 XD Oud Gastel
The Netherlands
Tel: [phone]
Fri-Jado Inc.
1401 Davey Road, Suite 100
Woodridge IL 60517
USA
Tel: [phone]
www.frijado.com