Frico PL2200C Series User manual

PL2200C
Suitable for small entrances
.... 15
GB .... 21
FR

PL2200C
2
145
345
40
183
78
16540
1026 / 1536 / 2026
20
210
10
145
min 500
min 500 min 500
145
62 40
22
Cu ø1
5
min 500 min 500 145
145
ø17, 5ø17,5
ø32,5
ø25,5
ø20,5
ø1
7, 5
Gland
Knock-out
Knock-out
Knock-out
Gland
Fig.1
Fig.2
Gland
2 m
W/A
E

PL2200C
3
Fig.3: Open the unit.
A
B
TX20
C

30 mm
60 mm
PL2200C
4
Fig.4.
Fig.5.
Minimum distance
min 60

PL2200C
5
min 500 mm
Fig. 6: Mounting with wall brackets
Mounting with wall brackets
AB
C
PL2210C 2 pcs
PL2215C 2 pcs
PL2220C 3 pcs
D
203575
210
33
ø8 (3x)
ø5
ø10
162

Accessories
PA34TR15 PL2210C, PL2215C, 1 m
PA34TR20 PL2220C, 1 m
PA2P15 PL2210C, PL2215C, 1 m
PA2P20 PL2220C, 1 m
PA2PF15 PL2210C, PL2215C
PA2PF20 PL2220C
PAMLK PL2200C
PAWAK PL2200C W
FHDN15 PL2200C W
PL2DR
VOT
VOT15 DN15
VOT20 DN20
VOT25 DN25
VKF15LF DN15
VKF15NF DN15
VKF20 DN20
VKF25 DN25
VKF32 DN32
SD230
BPV10
VKF
SD230 BPV10
VLSP
PL2200C
6
PL2DR
PA34TR PA2P
PA2PF
PAMLK FHDN15
PAWAK

PL2210CA/ PL2215CA/ PL2220CA
PL2210CA PL2215CA PL2220CA
Right motorLeft motor
Only 2 m version
PL2200C
7

PL2210CE05
5A x 3
5A
16A
NH1H2
N
1
On
Off
F1 F2 F3
on/off 2
N
LPE NL
PE
~
0 -10V
0 - 10V HEAT
ALARM
WATER
INTERNAL SENSOR
IR
M
Blue
Black
Brown
C°
~
Over heat cut-out
°C
C1
L2 PE
L1 LN
L3
400V 3N~
L2 PE
L1 LN
L3
230V~
PL2210CE05
C3
Run
C2 Lo
C1
Mid
PL2200C
8

PL2215CE08/ PL2220CE10
5A x 3
5A
16A
NH1H2
N
1
On
Off
F1 F2 F3
on/off2
N
LPE NL
PE
~
0 -10V
0 - 10V HEAT
ALARM
WATER
INTERNAL SENSOR
IR
C2
Over heat cut-out
°C
C1
L2 PE
L1 LN
L3
400V 3N~
Over heat
°C
cut-out
PL2215CE08 PL2220CE10
M
Blue
Black
Brown
C°
~
Right motor
M
Blue
Black
Brown
C°
~
C3
Run
C2 Lo
C1
Mid
Left motor
Only 2 m version
C3
Run
C2 Lo
C1
Mid
C4
C3
L2 PE
L1
L3
400V3~
PL2200C
9

PL2210CW/ PL2215CW/ PL2220CW
5A x 3
5A
16A
NH1H2
N
1
On
Off
F1 F2 F3
on/off2
N
LPE NL
PE
~
0 -10V
0 - 10V HEAT
ALARM
WATER
INTERNAL SENSOR
IR
PL2210CW PL2215CW PL2220CW
M
Blue
Black
Brown
C°
~
Right motor
M
Blue
Black
Brown
C°
~
C3
Run
C2 Lo
C1
Mid
Left motor
Only 2 m version
C3
Run
C2 Lo
C1
Mid
Black
Brown Blue
PL2200C
10

M
Blue
Black
Brown
C°
~
Lo
Mid
Run
Right motor
NF1F2F3
OUT PAMLK
CNC NO
Motor alarm (pot. free contact)
M
Blue
Black
Brown
C°
~
Lo
Mid
Run
Left motor
Only 2 m version
5A x 3
5A
16A
NH1H2
N
1
On
Off
F1 F2 F3
on/off 2
N
LPE NL
PE
~
0 -10V
0 - 10V HEAT
ALARM
WATER
INTERNAL SENSOR
IR
On
Off
M
C°
~
PAMLK, motor alarm card
PL2200C
11

PL2200C
12
Output charts water PL2200C
*1) Recommended outlet air temperature for good comfort and optimized output.
*2) Nominal output at given supply and return water temperature.
Supply water temperature: 80 °C
Room temperature: +18 °C
Outlet air temperature: +35 °C*1
Water temperature: 80/60 °C
Room temperature: +18 °C
Type Fan
position
Airflow
[m3/h]
Output
[kW]
Return
water
temp.
[°C]
Water
flow
[l/s]
Pressure
drop
[kPa]
Output *2
[kW]
Outlet
air temp.
[°C]
Water
flow
[l/s]
Pressure
drop
[kPa]
PL2210CW max 1200 6,9 60,2 0,09 7, 3 6,9 35,0 0,08 7, 2
min 700 4,0 49,7 0,03 1,4 5,0 39,2 0,06 4,1
PL2215CW max 1800 10,4 56,1 0,11 6,2 11,1 36,2 0,14 9,6
min 1000 5,8 45,5 0,04 1,2 7, 8 40,8 0,10 5,1
PL2220CW max 2400 13,9 57,9 0,14 6,2 14,4 35,7 0,18 7, 9
min 1400 8,1 47,9 0,06 1,2 10,5 40,0 0,13 4,5
Supply water temperature: 90 °C
Room temperature: +18 °C
Outlet air temperature: +35 °C*1
Water temperature: 90/70 °C
Room temperature: +18 °C
Type Fan
position
Airflow
[m3/h]
Output
[kW]
Return
water
temp.
[°C]
Water
flow
[l/s]
Pressure
drop
[kPa]
Output *2
[kW]
Outlet
air temp.
[°C]
Water
flow
[l/s]
Pressure
drop
[kPa]
PL2210CW max 1200 6,9 57,8 0,05 3,1 8,5 38,8 0,10 10,2
min 700 4,0 48,1 0,02 0,8 6,2 44,1 0,08 5,8
PL2215CW max 1800 10,4 53,1 0,07 2,9 13,6 40,2 0,17 13,5
min 1000 5,8 43,3 0,03 0,7 9,5 45,9 0,12 7, 0
PL2220CW max 2400 13,9 55,4 0,10 2,7 1 7, 7 39,7 0,22 11,1
min 1400 8,1 46,2 0,05 0,7 12,8 45,0 0,16 6,3
Supply water temperature: 110 °C
Room temperature: +18 °C
Outlet air temperature: +35 °C*1
Water temperature: 110/80 °C
Room temperature: +18 °C
Type Fan
position
Airflow
[m3/h]
Output
[kW]
Return
water
temp.
[°C]
Water
flow
[l/s]
Pressure
drop
[kPa]
Output *2
[kW]
Outlet
air temp.
[°C]
Water
flow
[l/s]
Pressure
drop
[kPa]
PL2210CW max 1200 6,9 53,7 0,03 1,1 10,4 43,5 0,09 6,9
min 700 4,0 45,4 0,02 0,4 7, 6 50,0 0,06 3,9
PL2215CW max 1800 10,4 48,1 0,04 1,1 16,7 45,3 0,14 9,2
min 1000 5,8 39,8 0,02 0,3 11,7 52,3 0,10 4,8
PL2220CW max 2400 13,9 51,1 0,06 1,0 21,7 44,6 0,18 7, 5
min 1400 8,1 43,4 0,03 0,3 15,8 51,2 0,13 4,2
Supply water temperature: 70 °C
Room temperature: +18 °C
Outlet air temperature: +35 °C*1
Water temperature: 70/50 °C
Room temperature: +18 °C
Type Fan
position
Airflow
[m3/h]
Output
[kW]
Return
water
temp.
[°C]
Water
flow
[l/s]
Pressure
drop
[kPa]
Output *2
[kW]
Outlet
air temp.
[°C]
Water
flow
[l/s]
Pressure
drop
[kPa]
PL2210CW max 1200 6,9 62,5 0,23 43,1 5,3 31,0 0,07 4,6
min 700 4,0 51,7 0,05 3,3 3,9 34,3 0,05 2,7
PL2215CW max 1800 10,4 59,3 0,24 26,7 8,7 32,2 0,11 6,3
min 1000 5,8 48,0 0,06 2,6 6,0 35,8 0,07 3,3
PL2220CW max 2400 13,9 60,5 0,35 28,5 11,1 31,6 0,14 5,1
min 1400 8,1 50,0 0,10 2,9 8,1 35,0 0,10 2,9

PL2200C
13
Supply water temperature: 60 °C
Room temperature: +18 °C
Outlet air temperature: +32 °C
Water temperature: 60/40 °C
Room temperature: +18 °C
Type Fan
position
Airflow
[m3/h]
Output
[kW]
Return
water
temp.
[°C]
Water
flow
[l/s]
Pressure
drop
[kPa]
Output *2
[kW]
Outlet
air temp.
[°C]
Water
flow
[l/s]
Pressure
drop
[kPa]
PL2210CW max 1200 5,7 55,0 0,28 64,4 3,7 27,0 0,05 2,5
min 700 3,3 46,3 0,06 4,0 2,7 29,3 0,03 1,4
PL2215CW max 1800 8,6 52,5 0,28 36,5 6,1 28,0 0,07 3,6
min 1000 4,8 43,3 0,07 3,1 4,3 30,6 0,05 1,9
PL2220CW max 2400 11,4 53,4 0,42 39,7 7, 8 27,5 0,09 2,8
min 1400 6,7 44,9 0,11 3,5 5,6 29,8 0,07 1,6
*1) Recommended outlet air temperature for good comfort and optimized output.
*2) Nominal output at given supply and return water temperature.
Supply water temperature: 55°C
Room temperature: +18 °C
Outlet air temperature: +29 °C
Water temperature: 55/35°C
Room temperature: +18 °C
Type Fan
position
Airflow
[m3/h]
Output
[kW]
Return
water
temp.
[°C]
Water
flow
[l/s]
Pressure
drop
[kPa]
Output *2
[kW]
Outlet
air temp.
[°C]
Water
flow
[l/s]
Pressure
drop
[kPa]
PL2210CW max 1200 4,5 46,5 0,13 16,3 2,8 24,9 0,03 1,6
min 700 2,6 40,0 0,04 2,3 2,0 26,5 0,02 0,9
PL2215CW max 1800 6,7 44,2 0,15 12,5 4,9 25,9 0,06 2,4
min 1000 3,7 37,4 0,05 1,9 3,4 27,9 0,04 1,3
PL2220CW max 2400 9,0 45,2 0,22 12,8 6,0 25,4 0,07 1,8
min 1400 5,2 38,9 0,08 2,1 4,3 27,1 0,05 1,0
Output charts water PL2200C

PL2200C
14
Type Output
[kW]
Airflow
[m3/h]
Sound
level*1
[dB(A)]
Voltage
motor
[V]
Amperage
motor
[A]
Length
[mm]
Weight
[kg]
PL2210CA 0 900/1200 42/51 230V~ 0,45 1026 16
PL2215CA 0 1150/1800 40/52 230V~ 0,5 1536 24
PL2220CA 0 1800/2400 43/53 230V~ 0,9 2026 32
Type Output
step
[kW]
Airflow
[m3/h]
∆t*2
[°C]
Sound
level*1
[dB(A)]
Voltage
motor
[V]
Amperage
motor
[A]
Voltage [V]
Amperage [A]
(heat)
Length
[mm]
Weight
[kg]
PL2210CE05 3,3/5 900/1200 17/12,5 42/51 230V~ 0,45 400V3~/7,2 1026 17
PL2215CE08 4/8 1150/1800 21/13 40/52 230V~ 0,5 400V3~/11,5 1536 26
PL2220CE10 5/10 1800/2400 17/12,5 43/53 230V~ 0,9 400V3~/14,4 2026 34
Type Output*3
[kW]
Airflow
[m3/h]
∆t*2,3
[°C]
Water
volume
[l]
Sound
level*1
[dB(A)]
Voltage
motor
[V]
Amperage
motor
[A]
Length
[mm]
Weight
[kg]
PL2210CW 6,9 700/1200 21/17 0,38 39/52 230V~ 0,4 1026 17
PL2215CW 11,1 1000/1750 23/18 0,81 37/53 230V~ 0,5 1536 26
PL2220CW 14,4 1400/2400 22/18 0,74 40/53 230V~ 0,8 2026 35
Technical specifications | PL2200C W with water heat 2
Technical specifications | PL2200C E with electrical heat 3
Technical specifications | PL2200C A without heat 1
*1) Conditions: Distance to the unit 5 metres. Directional factor: 2. Equivalent absorption area: 200 m². At lowest/highest airflow.
*2) ∆t = temperature rise of passing air at maximum heat output and lowest/highest airflow.
*3) Applicable at water temperature 80/60 °C, air temperature, in +18 °C.
Protection class for units with electrical heating: IP20.
Protection class for units without heating and units with water heating: IP21.
CE compliant.
Type C1 Mid
[mF]
C2 Low
[mF]
C2 Run
[mF]
PL2210CE05 6 5 3
PL2215CE08 8 6 4
PL2220CE10 6 5 3
PL2210CW 7 5 3
PL2215CW 8 6 4
PL2220CW 7 5 3
PL2210CA 6 5 3
PL2215CA 8 6 4
PL2220CA 6 5 3

15
GB
General Instructions
Read these instructions carefully before
installation and use. Keep this manual for
future reference.
The product may only be used as set out in
the assembly and operating instructions. The
guarantee is only valid if the product is used
in the manner intended and in accordance
with the instructions.
Application area
The PL2200C air curtain unit is supplied
without heating, with electrical heating or hot
water heating.
The PL2200C is a compact air curtain,
suitable for most small entrances up to
2.2 metres in height. The air curtain has
an integrated control system and can be
remotely controlled.
Protection class for units with electrical
heating: IP20.
Protection class for units without heating and
units with water heating: IP21.
Operation
Air is drawn in at the top of the unit and
blown out downwards so that it shields the
door opening and minimizes heat loss. To
achieve the optimum curtain effect the
unit must extend the full width of the door
opening.
The grille for directing exhaust air is
adjustable and is normally angled outwards to
achieve the best protection against incoming
cold air.
The efficiency of the air curtain depends
on the air temperature, pressure differences
across the doorway and any wind pressure.
NOTE! Negative pressure in the building
considerably reduces the efficiency of the air
curtain. The ventilation should therefore be
balanced.
Mounting
The air curtain unit is installed horizontally
with the supply air grille facing downwards
as close to the door as possible. Minimum
distance from outlet to floor for electrically
heated units is 1800 mm. For other minimum
distances, see fig. 4.
Mounting with wall brackets (fig. 6)
1. Mount the brackets on the wall, see fig.6A
and dimension drawing fig.1. If the wall is
uneven the brackets must be compensated for
this.
2. Hook on the unit at the lower edge of the
brackets. (Fig.6B-C)
3. Bend the top of the console over the the
unit and slide the units screws along the rail
into the slots on the consoles. (Fig.6D) When
the bracket is bent once, it must be replaced
if bent back more than 45 °.
4. Lock the nuts against the brackets.
(Fig.6E)
Horizontal mounting on the ceiling
Threaded rods, hanging brackets and ceiling
mounting brackets for ceiling mounting are
available as accessories, see accessories pages
and separate manuals.
Electrical installation
The installation, which should be preceded by
an omnipolar switch with a contact separation
of at least 3 mm, should only be wired by a
competent electrician and in accordance with
the latest edition of IEE wiring regulations.
The control system is pre-installed in the
air curtain.
Unit without heating
Connected via the built-in control board with
1,5 m cord and plug.
Unit with water heating
Connected via the built-in control board with
1,5 m cord and plug.
Assembly and operating instructions

16
GB
Unit with electrical heating
The electrical installation is made on the
top of the unit, fig.2. Units are intended
for permanent installation. Control supply
(230V~) and power supply for heating
(400V3~) are connected to terminal block
in the internal connection boxes. 2-metre
units require dual power supplies. The largest
cable diameter for the terminal block is
16 mm². The cable glands used must meet
the protection class requirements. In the
distribution board it is to be indicated that
”the air curtains can be supplied from more
than one connection”.
See wiring diagrams.
Start-up (E)
When the unit is used for the first time or
after a long period of disuse, smoke or odour
may result from dust or dirt that has collected
on the element. This is completely normal
and disappears after a short time.
Connecting the water coil (W)
The installation must be carried out by an
authorised installer.
The water coil has copper tubes with
aluminium louvres and is suitable for
connection to a closed water heating system.
The heating coil must not be connected to
a mains pressure water system or an open
water system.
Note that the unit shall be preceded by a
regulating valve, see valve kit.
The water coil is connected on the upper
side of the unit with ø15 mm smooth copper
pipe with a suitable coupling or soldering.
The connections to the heating coil must be
equipped with shut off valves (not included)
to allow problem free removal. Water coil is
equipped with a drain valve.
A vent valve should be connected at a high
point in the pipe system. Air valves are not
included.
NOTE: Care must be taken when connecting
the pipes. Use a wrench or similar to hold the
air curtain connections to prevent straining
of the pipes and subsequent water leakage
during connection to water supply pipe-work.
Adjustment of the air curtain and air flow
The direction and speed of the air flow should
be adjusted considering the load on the
opening. Pressure forces affect the air stream
and make it bend inwards into the premises
(when the premises are heated and the
outdoor air is cold).
The air stream should therefore be directed
outwards to withstand the load. Generally
speaking, the higher the load, the greater the
angle that is needed.
Basic setting fan speed
The fan speed when the door is open is set
using the control. Note that the air flow
direction and fan speed may need fine
adjustment depending on the loading of the
door.
*1)Dimensioning of external wiring shall comply with applicable
regulations and local deviations may occur.
Type Output
[kW]
Voltage
[V]
Minimum
area*1
[mm2]
Control 0 230V~ 1,5
PL2210CE05 5 400V3~ 1,5
PL2215CE08 8 400V3~ 2,5
PL2220CE10 10 400V3~ 2,5

17
GB
Filter (W)
The water coil is protected against dirt and
blockage by an internal air filter which covers
the coil face.
Service, repairs and maintenance
For all service, repair and maintenance first
carry out the following
1. Disconnect the power supply.
2. The front hatch is removed by removing
the screws on the top of the unit and then
detach the bent edge at the bottom. (Fig.3)
3. After the service, repair and maintenance
reattach the front hatch. Place the hatch at
the lower edge with the bent edge and fasten
on top with screws.
Maintenance
Unit with water heating
The appliance filter should be cleaned
regularly to ensure the air curtain effect and
the heat emission from the device. How often
depends on local circumstances. A clogged
filter is not a risk, but the appliance function
can fail.
1. Disconnect the power supply.
2. The front hatch is removed by removing
the screws on the top of the unit and then
detach the bent edge at the bottom. (Fig.3)
3. Remove the filter and vacuum clean or
wash it. If the filter is clogged or damaged, it
may need to be changed.
All units:
Since fan motors and other components are
maintenance free, no maintenance other than
cleaning is necessary. The level of cleaning
can vary depending on local conditions.
Undertake cleaning at least twice a year. Inlet
and exhaust grilles, impeller and elements
can be vacuum cleaned or wiped using a
damp cloth. Use a brush when vacuuming
to prevent damaging sensitive parts. Avoid
the use of strong alkaline or acidic cleaning
agents.
Overheating
The air curtain unit with electric heater is
equipped with an overheat protector. If it is
deployed due to overheating, reset as follows:
1. Disconnect the electricity with the fully
isolated switch.
2. Determine the cause of overheating and
rectify the fault.
3. Remove the front hatch.
4. Press the red button located inside the
air curtain unit, at the inner gable of the
connection box.
5. Reattach the front hatch and connect the
unit again.
All motors are equipped with an integral
thermal safety cut-out. This will operate,
stopping the air curtain should the motor
temperature rise too high. The cut-out
will automatically reset when the motor
temperature has returned to within the
motor’s operating limits.
Temperature control
See control pages.
Replacing motor or impeller
1. Remove gable end.
2. Remove the screw between motor and fan.
3. Disconnect the cables to the motor.
4. Remove the screws securing the motor and
lift it out together with the impeller.
5. Install the new motor and/or the new
impeller as above in reverse order.
Replacing the electrical coil (E)
1. Mark and disconnect the cables to the
electric coil.
2. Remove the mounting screws securing the
electric coil in the unit and lift the electric
coil out.
3. Replace faulty electrical coil.
4. Install the new electric coil in reverse
order to the above.
Replacing the water coil (W)
1. Shut off the water supply to the unit.
2. Disconnect the connections to the water
coil.
3. Remove the mounting screws securing the
coil in the unit and lift the coil out.
4. Install the new coil in reverse order to the
above.

18
GB
Draining the water coil (W)
The drain valves is on the underside of the
coil on the connector side. It can be accessed
via the front hatch.
Trouble shooting
If the fans are not working or do not blow properly,
check the following:
• The functions and settings of the built-in
control system.
• That the intake grille/filter is not dirty.
If there is no heat, check the following:
• The functions, internal sensor and settings
of the built-in control system.
For units with electrical heating, check also the fol-
lowing:
• Power supply to electric heater coil; check
fuses and circuit-breaker (if any).
• That the overheat protection for the motors
has not been deployed.
For units with water coil, check also the following:
• That the water coil is air free.
• That there is enough water flow.
• That incoming water is heated enough.
If the fault cannot be rectified, please contact
a qualified service technician.
Residual current circuit breaker (E)
When the installation is protected by means
of a residual current circuit breaker, which
trips when the appliance is connected,
this may be due to moisture in the heating
element. When an appliance containing a
heater element has not been used for a long
period or stored in a damp environment,
moisture can enter the element.
This should not be seen as a fault, but is
simply rectified by connecting the appliance
to the mains supply via a socket without a
safety cut-out, so that the moisture can be
eliminated from the element. The drying
time can vary from a few hours to a few days.
As a preventive measure, the unit should
occasionally be run for a short time when it is
not being used for extended periods of time.
Safety
• For all installations of electrically heated
products should a residual current circuit
breaker 300 mA for fire protection be used.
• Keep the areas around the air intake
and exhaust grilles free from possible
obstructions!
• During operation the surfaces of the unit
can be hot!
• The unit must not be fully or partially
covered with clothing, or similar
materials, as overheating can result in a
fire risk! (E)
• This appliance can be used by children
aged from 8 years and above and persons
with reduced physical, sensory or
mental capabilities or lack of experience
and knowledge if they have been given
supervision or instruction concerning
use of the appliance in a safe way and
understand the hazards involved. Children
shall not play with the appliance. Cleaning
and user maintenance shall not be made
by children without supervision.

1234
ON
1234
ON
19
GB
230V~
Controls
The air curtain has an integrated control
system and can be remotely controlled.
PL2DR
(accessory)
ON
Factory setting dip-switches
Units with water heating.
Dip-switch 3 is used for PL2DR (optional).
Factory setting dip-switches
Units with electrical heating and no heat
Dip-switch 3 is used for PL2DR (optional).
OFF
Actuator SD230
(remove the quick
connector)
External on/off
Eg time switch.
External potential free
closure = off
Black
Brown
Blue

20
GB
Functional test
Functional test is started using the remote
control.
Push
and
in 5 seconds
Fan and heatings steps are tested in
10-second intervals which is indicated by
lighted LEDs. When the test is completed, all
LEDs will flash for 30 seconds.
Heat step
Electric: Half/full power
Water: On/off (1 LED)
On/off
~20 °C
Control panel
Units with electric heating and water heating
Remote control - on/off, fan steps and heating steps
Temperature control
If the temperature exceeds 50 °C, the fan runs
at full speed for 2 minutes to vent out the
heat, if the temperature rises above
50 °C again during the following 5 minutes
overheating alarm is deployed. The red LEDs
flash and all the buttons are locked.
1. Disconnect the electricity with the fully
isolated switch.
2. Determine the cause of overheating and
rectify the fault.
3. Connect the unit again.
Fan step 1/2/3
Control panel
Units with no heat
On/off
Fan step 1/2/3