Front Runner JADA010 User manual

ENG
hi-lift Jack bracket
JADA010_REV_B05 © 2021 FRONT RUNNER VEHICLE OUTFITTERS
1
JADA010
front runner
Thank you for purchasing a Front Runner Hi-Lift Jack Bracket.
Before you start, take a moment to familiarize yourself with the Fitting Instructions and the components received.
Refer to Page 2 for a list of all the components, quantities and tools required.
READ ME !
IMPORTANT WARNING!
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT
RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND
DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
Please call us if you have any questions about the installation of this product.

JADA010_REV_B05 © 2021 FRONT RUNNER VEHICLE OUTFITTERS 2
IN THE BOX
FIGURE 1.1
1 1 X M10x40 Hex Bolt
2 3 X M10x30x3 Flat Washer
3 4 X M8x25 Button Head Bolt (Black)
4 10 X M8x16x1.6 SS Flat Washer
5 1 X Base Bracket
6 1 X M10 Wing Nut
7 1X M12 Nyloc Hex Nut
8 1 X M12 Flat Washer
11 8 X M8 Nyloc Hex Nut
12 2 X M8x16 Button Head Bolt (Black)
13 1 X M12 Machined Stud
14 2 X Support Bracket
IN THE BOX
TOOLS NEEDED
4mm
5mm
Allen Key
IN THE BOX IN THE BOX
18 2 X M8x30 Button Head Bolt (Black)
19 2 X M8 Nut Cap
20 2 X M8 x 20 Hex Bolt
IN THE BOXIN THE BOX CONTINUED
Marker
1
87
6432
1812 13411
25
15 1 X Handle Clamp Assembly
16 1 X M10 Tie Down Ring
17 2 X M8x20 Button Head Bolt (Black)
19
11
14
4
20
1GET ORGANIZED
Here is what you are looking at for JADA010

2
4
16
3
15
17
4
12
18
4
11
FIGURE 1.2
1
11
4
14
1
1GET ORGANIZED CONTINUED
© 2021 FRONT RUNNER VEHICLE OUTFITTERS
3 JADA010_REV_B05
RECOMENDED POSITIONS
2
2.1
Please note that it is not recommended to mount your Hi-Lift Jack on the front or rear of your Rack
only on the sides.
For ease of instruction, we have chosen to describe one orientation of mounting the Jack Bracket.
The principals are the same, just the positioning and orientation of the brackets may vary depending
on where you want to mount the jack.
Decide where on your Rack you would like to mount the Hi-Lift Jack. The brackets can be orientated
upwards, downwards, front to back and back to front. Refer to Page 4, showing the various
mounting options.

© 2021 FRONT RUNNER VEHICLE OUTFITTERS
4 JADA010_REV_B05
2.2
RECOMENDED POSITIONS
2
X
X
X
X
X
THIS POSITION IS NOT SUITED FOR A HI LIFT JACK.
IMPORTANT WARNING!
IMPORTANT WARNING!

© 2021 FRONT RUNNER VEHICLE OUTFITTERS
5 JADA010_REV_B05
3.1
3.2
3.3
Fit and Secure Base Bracket in desired
position as shown.
Secure as shown. Insert 2 M8 Hex Nuts
at the point indicated by the arrow.
Assemble the machined pin and
securing bolt in hole patern suited to
your jack.
FIT AND SECURE
3
5 2
6 2 13
1
7
9
3.4
Fit and Secure the handle clamp in the
desired position, using fasteners shown
in Figure 1.2
15
16 17
5mm
13mm
5mm
13mm
5mm
5mm
17mm
5
4
18
REMOVE FROM SLAT
11
5
4
3
19
20
14

© 2021 FRONT RUNNER VEHICLE OUTFITTERS
6 JADA010_REV_B05
INSTALL OTHER VEHICLE AND RACK ACCESSORIES
5
Now's the time to visit your favorite Front Runner Dealer in person or online.
Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters #BornToRoam
Share your adventures on:
FINISH
4
Congratulations! You did it. Take a step back and admire your work!