Front Runner SSDS102 User manual

SSDS102_REV_A02 © 2019 FRONT RUNNER VEHICLE OUTFITTERS
TOYOTA FJ CRUISER
dECK cOMPLETION SET
front runner
SSDS102
ENG
1
Thank you for purchasing a Front Runner Deck Completion Set.
Before you start, take a moment to familiarize yourself with the Fitting Instructions and the components received.
Refer to Page 2 for a list of all the components, quantities and tools required.
READ ME !
IMPORTANT WARNING!
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT
RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND
DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
Please call us if you have any questions about the installation of this product.

SSDS102_REV_A02 © 2019 FRONT RUNNER VEHICLE OUTFITTERS 2
TOOLS NEEDED
FIGURE 1.1
GET ORGANIZED
1
IN THE BOX
1LH
1RH
2
2
8
7
4LH
4LH
4RH
5
9
9
6
10
11
12
3
12
11
10
1 2 X Side Deck - 1LH + 1RH
2 2 X Rear Deck (Symmetrical)
3 1 X Rear Support
4 6 X Side Wings - 3LH + 3RH
5 2 X Front Face - 1LH + 1RH - (With Knockouts)
6 2 X 37mm Laser Cut Carabiner
7 2 X M6 x 25 Countersink Bolt
8 2 X M6 Finishing Washer
9 4 X M6 x 16 Button Head Bolt
10 8 X M6 x 19 x 1SS Flat Washer
11 8 X M6 SS Spring Washer
12 8 X M6 x 16 Hex Bolt
13 2 X Front Face 1LH + 1RH
4mm
10mm
13
4LH
4RH

SSDS102_REV_A02 © 2019 FRONT RUNNER VEHICLE OUTFITTERS
3
FIT AND SECURE2
2.1
2.2
2.3
Looking at the rear of the Drawer System,
remove the fasteners as indicated by the
arrows. Keep the fasteners safe as they will
be used in Step 2.2.
Assemble the Rear Support using M6 x 16
Hex Bolts, M6 SS Spring Washers and M6 x
19 x 1SS Flat Washers (Items 10, 11 & 12)
as shown.
Assemble two Side Wings (Item 4LH & 4RH)
on each of the rear left and right corner
of the Drawer System using the fasteners
removed in Step 2.1 together with D-Rings
(supplied with SSDR011) and M6 x 16 Hex
Bolts, M6 SS Spring Washers and M6 x 19
x 1SS Flat Washer (Items 10, 11 & 12) as
shown.
Assemble two Side Wings (Item 4LH & 4RH)
on the left and right side of the Drawer
together with D-Rings (supplied with
SSDR011) using M6 x 16 Hex Bolts, M6 SS
Spring Washers and M6 x 19 x 1SS Flat
Washer (Items 10, 11 & 12) as shown.
4RH
12
11
10
12
11
10
4RH 4LH
3
10mm

FIT AND SECURE2
2.4
2.5
2.6
Place the Drawer System into the vehicle.
Position the Drawer 45mm in from the
plastic tread section and center the Drawer
left to right.
Before securing the Drawer down, assemble
a Wing Nut to each of the four Turnbuckles.
(Wing Nuts and Turnbuckles supplied with
SSDR011).
Loosely secure the rear of the Drawer
System to the tie down points found behind
the vehicles rear seats using Turnbuckles
and 60mm Carabiners (supplied with
SSDR011) as shown.
Loosely secure the front of the Drawer
System to the tie down points found at the
rear of the vehicles using Turnbuckles
and (supplied with SSDR011) and 37mm
Carabiner (Item 6) as shown.
Tighten all the Turnbuckles making sure
that the Drawer System remains centered
left to right and 45mm in from the plastic
tread section. Tighten the Wing Nuts to lock
the Turnbuckles in place..
Assemble the two Front Faces (Item 5 or 13)
to the Drawer System using M6 x 16 Button
Head Bolts (Item 9).
SSDS102_REV _A02 © 2019 FRONT RUNNER VEHICLE OUTFITTERS 4
5
9
13
6

SSDS102_REV _A02 © 2019 FRONT RUNNER VEHICLE OUTFITTERS 5
INSTALL OTHER VEHICLE AND RACK ACCESSORIES
5Now's the time to visit your favorite Front Runner Dealer in person or online.
Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters #BornToRoam
Share your adventures on:
COMPLETION
4
9
Congratulations! You did it. Take a step back and admire your work!
FIT AND SECURE2
2.7
Place the Rear and Side Decks (Items 1 & 2)
into position. Secure the center of the Rear
Decks to the Rear Support (Item 3) using
M6 x 25 Countersink Bolts and M6 Finishing
Washers (Items 7 & 8) as shown.
4RH
FITTING ELECTRICAL SOCKETS
3
Twist the pre cut knock outs to remove.
These cut outs can then be used to fit Front
Runners range of electrical sockets.
(Sold Separately)
ECOM117 - Amp
ECOM118 - USB
ECOM119 - 12/24V
ECOM120 - Merit
ECOM121 - Engel
ECOM124 - Volt
3.1
1LH
27
8