Front Runner SSDS110 User manual

SSDS110_REV_A01© 2019 FRONT RUNNER VEHICLE OUTFITTERS
DRAWER DECK COMPLETION SET
SSDS110
ENG
1
Toyota fortuner 2016-Current
Thank you for purchasing a Front Runner Deck Completion Set.
Before you start, take a moment to familiarize yourself with this Fitting Instruction and the components received.
Refer to Page 2 for a list of all the components, quantities and tools required.
READ ME !
IMPORTANT WARNING!
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT
RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND
DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
Please call us if you have any questions about the installation of this product.

SSDS110_REV_A01© 2019 FRONT RUNNER VEHICLE OUTFITTERS 2
TOOLS NEEDED
10MM
8MM
10MM
14MM
13MM
3MM
4MM
REAR OF VEHICLE
11X Side Deck LH
21X Side Deck RH
32X Rear Tie-Down Bracket LH And RH
42X Drawer Front Ajustable Bracket LH And RH
52X Front Tie-Down Bracket LH And RH
62X Front Face LH And RH
72X Drawer Front Fixed Bracket LH And RH
82X Drawer RearMount LH And RH
92X Drawer RearMount Clamp LH and Rh
10 4 X M6x12 Button Head
11 4 X M6 Flat Washer
12 8 X M6 Nyloc Nut
13 12 X M6x19x1SS Flat Washer
14 4 X Carabiner Hook 37mm
15 4 X M6 Spring Washer
16 8 X M6x16 Hex Bolt
17 4 X M5 Nyloc
18 4 X M5x10x1SS Flat Washer
19 4 X M5x10 Button Head
20 2 X Pinchweld 465mm
21 2 X Front Face 1LH + 1RH - With Knockouts
FIGURE 1.1
3
19
20
6LH
7LH
8LH
9LH
18
17
16
1
13
5RH
3RH
13
12
10
9RH
12
11
8RH
2
14
16
7RH
15
13
4LH
7RH
3LH
5LH
4RH
GET ORGANIZED
1
IN THE BOX
21

SSDS110_REV_A01 © 2019 FRONT RUNNER VEHICLE OUTFITTERS 3
D-Ring
FIT AND SECURE
2
2.2
2.3
2.4
2.1
2.1
2.2
2.3
Secure the front and rear tie-down
bracket using the existing bolts you
removed from the seats and the bottom
seat belt bolts. Do this on left and right
side of the vehicle.
Move the 2 D-rings to the middle mounting
holes as shown .
Remove the the rear jump seats.
14MM
13MM
14MM
5LH
3LH

SSDS110_REV_A01 © 2019 FRONT RUNNER VEHICLE OUTFITTERS 4
5RH
3RH
14
2.2
2.3
FIT AND SECURE
2
2
2.4
2.1
2.4
2.5
2.6
Secure the drawer to the tie-down points
using the items shown in 2.6
Before securing the drawer, make sure
that the rear door does not interfere with
the drawer.
The turnbuckles and C-hooks are
supplied with SSDR005
Place the drawer in the vehicle before
assembling the wings to the drawer.
Refer to 1.1 for wing placement.
10MM
10MM
10MM
4MM
Loosen the rear deck and secure the rear
wings as shown. Refer to 1.1 for
wing placement.
12
10
9RH
7RH
16
15
8RH
11
12
13
4RH
elkcuBnruT
C-Hook

SSDS110_REV_A01 © 2019 FRONT RUNNER VEHICLE OUTFITTERS
5
2FIT AND SECURE
19
18
17
7RH
20
3MM
8MM
Fit the side decks (item 1 and 2).
2.7
2.8
21
Assemble the two Front Faces (Item 20
or 21) to the Drawer System using M5
x 10 Button Head, M5 Flat Washers and
M5 Nyloc Nuts (Item 17, 18 & 19).

SSDS110_REV _A01 © 2019 FRONT RUNNER VEHICLE OUTFITTERS 6
INSTALL OTHER VEHICLE AND RACK ACCESSORIES
5Now's the time to visit your favorite Front Runner Dealer in person or online.
Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters #BornToRoam
Share your adventures on:
COMPLETION
4
9
Congratulations! You did it. Take a step back and admire your work!
21
FITTING ELECTRICAL SOCKETS
3
Twist the pre cut knock outs to remove.
These cut outs can then be used to fit Front
Runners range of electrical sockets.
(Sold Separately)
ECOM117 - Amp
ECOM118 - USB
ECOM119 - 12/24V
ECOM120 - Merit
ECOM121 - Engel
ECOM124 - Volt
3.1