Front Runner SSDR002 User manual

SSDR002_REV_A00 © 2020 FRONT RUNNER VEHICLE OUTFITTERS
SUV Asymmetric
Drawers /Large
SSDR002
ENG
1
Thank you for purchasing a Front Runner Universal Drawer.
Before you start, take a moment to familiarize yourself with the Fitting Instructions and the components received.
Refer to Page 2 for a list of all the components, quantities and tools required.
READ ME !
IMPORTANT WARNING!
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT
RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND
DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
Please call us if you have any questions about the installation of this product.

SSDR002_REV_A00 © 2020 FRONT RUNNER VEHICLE OUTFITTERS 2
TOOLS NEEDED
10MM
10MM
1 1 X Universal Drawer Large Pick-up
2 X Set Of Keys
2 6 X Eye Nut
3 6 X M8 Nylon Washer
4 6 X Stud Plate
5 4 X Carabiner
6 4 X M6 Wing Nut
7 4 X Turnbuckle
FIGURE 1.1
13MM
GET ORGANIZED
1
IN THE BOX
17
1
4
3
2
5
67

SSDR002_REV_A00 © 2020 FRONT RUNNER VEHICLE OUTFITTERS 3
D-Ring
D-Ring
FIT AND SECURE
2
2.1
2.2
2.3
Assemble each of the 4
turnbuckles (item 12) with a wing nut
(item 10) as shown. The wing nut will be
used to lock the turnbuckles after they
have been set.
Place the drawer in the vehicle
and position as desired. Making
sure the turnbuckles are pulling
outward to prevent the drawer
from moving after it has been secured.
Connect the C-hooks (item 6) onto the
D-rings on the drawers upright.
Connect the turnbuckles (item 7) on the
other side of the C-hooks and hook it into
the tie-down that are fitted to the
vehicle.
Secure the drawer by tensioning the
turnbuckles until there is no more
movement on the drawer. Make sure the
drawer stays in position when doing this.
Lock the turnbuckles with the wing nuts.
Do this by tightening the wing nuts up to
the turnbuckles.
Refer to diagram 2.1
10MM
5
7
6
6
7

SSDR002_REV_A00 © 2020 FRONT RUNNER VEHICLE OUTFITTERS 4
INSTALL OTHER VEHICLE AND RACK ACCESSORIES
4
Now's the time to visit your favorite Front Runner Dealer in person or online.
Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters #BornToRoam
Share your adventures on:
FINISH
3
Congratulations! You did it. Take a step back and admire your work!
FIT AND SECURE
2
2.4
4
3
2
Assemble the eye-nuts (item 2) with a
M8 nylon washer (item 3) and a stud plate
(item 4) and slide them into place.