Front Runner LAMS004 User manual

LAMS004_REV_A00 © 2022 FRONT RUNNER VEHICLE OUTFITTERS
front runner
LAMS004
ENG
1
Thank you for purchasing a Front Runner Mercedes Sprinter H2 Ladder.
Before you start, take a moment to familiarize yourself with the Fitting Instructions and the included components.
Refer to Page 2 for a list of all the components, quantities and tools required.
READ ME !
IMPORTANT WARNING!
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT
RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND
DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
Please call us if you have any questions about the installation of this product.
Mercedes Sprinter H1 Ladder

LAMS004_REV_A00 © 2022 FRONT RUNNER VEHICLE OUTFITTERS 2
TOOLS NEEDED
FIGURE 1.1
CHECK ONLINE FOR THE LATEST FITMENT GUIDE WWW.FRONTRUNNEROUTFITTERS.COM
GET ORGANIZED
1
5mm
1 1 X Ladder Top Assembly
2 10 X M6 x 16 Button Head Bolt
3 2 X Ladder Side Top
4 2 X Ladder Side Bottom
5 2 X Outer Joiner Channel
6 2 X Inner Joiner Channel
7 1 X Ladder Base Bracket
8 7 X Rung
9 1 X Ladder Base Mount Assembly
10 14 X M6 x 25 Thread Forming Screw
11 10 X M6 Nut Cap
12 13 X M6 Nyloc Nut
13 3 X M6 x 20 Button Head Bolt
14 3 X M6 x 20 x 2 Flat Washer
IN THE BOX
IN THE BOX
15 2 X M8 x 19 x 2 Flat Washer
16 4 X M8 Nyloc Nut
17 2 X M8 Nut Cap
18 1 X Top Stopper Rubber
19 2 X M8 x 16 Button Head Bolt
10mm 6.5mm
Torx
T30
Anti-
Rust
Anti-
Seize Marker
Loremipsum
14 13
7
16
15
17
9
2
10
6
12
11
5
2
10
3
4
8
16
1
19
12

C(1:1)
LAMS004_REV_A00 © 2022 FRONT RUNNER VEHICLE OUTFITTERS
3
FIT AND SECURE2
2.1
2.2
2.3
Secure the Ladder Rungs (Item 8) to the Top
and Bottom Ladder Sides (Item 3 & 4) using
M6 x 25 Thread Forming Screws (Item 10).
Fully tighten all fasteners.
Join the Ladder Top and Bottom using the
Outer and Inner Joiner Channels,
Add Text
10
3
8
3 4
4
8
10
2
5
11
12
6
1
2
11
12
Torx
T30
Anti-
Seize
Torx
T30
Anti-
Seize
5mm
10mm
Anti-
Seize
5mm
10mm
Apply a little Anti seize/oil on screw
threads before inserting.
Tightening Torque:
M6 : 8-10Nm / 5.9 ft lb - 7.38 ft lb

LAMS004_REV_A00 © 2022 FRONT RUNNER VEHICLE OUTFITTERS 4
FIT AND SECURE2
2.4
2.5
2.6
Add Text
Add Text
Add Text
2
10
15
16
17
9
12
11
13
14
12
16
19
Anti-
Rust
6.5mm
5mm
Torx
T30
Anti-
Seize
5mm
10mm
13mm
5mm
10mm
13mm

LAMS004
..............000000_REV
_A00 © 2022 FRONT RUNNER VEHICLE OUTFITTERS 5
INSTALL OTHER VEHICLE AND RACK ACCESSORIES
4
Now's the time to visit your favorite Front Runner Dealer in person or online.
Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters #BornToRoam
Share your adventures on:
FINISH
3
Congratulations! You did it. Take a step back and admire your work!