Front Runner LALD009 User manual

LALD009_REV_A00 © 2022 FRONT RUNNER VEHICLE OUTFITTERS
front runner
LALD009
ENG
1
Thank you for purchasing a Front Runner Land Rover Defender 90 / 110 Ladder.
Before you start, take a moment to familiarize yourself with the Fitting Instructions and the included components.
Refer to Page 2 for a list of all the components, quantities and tools required.
READ ME !
IMPORTANT WARNING!
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT
RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND
DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
Please call us if you have any questions about the installation of this product.
LAND ROVER DEFENDER 90/110 LADDER

LALD009_REV_A00 © 2022 FRONT RUNNER VEHICLE OUTFITTERS 2
FIGURE 1.1
CHECK ONLINE FOR THE LATEST FITMENT GUIDE WWW.FRONTRUNNEROUTFITTERS.COM
GET ORGANIZED1
IN THE BOX
1 2 X Ladder Side
2 1 X Ladder Top Assembly
3 3 X Ladder Step
4 1 X Support Bracket
5 2 X M8 x 35 Hex Head Bolt
6 4 X PVC Washer 24.5 x 2.5
7 2 X M8 x 25 x 2 Flat Washer
8 2 X M8 Nyloc Nut
9 2 X M8 Nut Cap
10 6 X M6 x 25 Thread Forming Screw
11 6 X M6 x 16 Flange Button Head
12 6 X M6 Nyloc Nut
13 1 X Bottom Step
14 2 X M10 x 80 Hex Head Bolt
15 1 X M10 x 100 Hex Head Bolt
16 1 X Aluminium Spacer
17 1 X M10 Flat Washer
IN THE BOX
18 1 X M10 x 30 x 3 Flat Washer
19 2 X M10 Nyloc Nut
20 6 X M6 Nut Cap
21 2 X M10 Nut Cap
22 2 X M6 x 19 x 1 Flat Washer
23 2 X M6 Spring Washer
24 2 X M6 x 60 Cap Screw
22
23
24
11
2
12
20
1
3 9 5
6 6
7
8
11
10
4
16
18
19
19
17
13
14
21
15
Torx
T30 Anti-
Rust
Anti-
Seize
TOOLS NEEDED
4mm
5mm
5mm
8.5mm
12mm
Marker
10mm
13mm

2794
4685
1.0m
0.5m
5cm
Scale: 1:25 All measurements in millimeters.
LALD009_REV_A00 © 2022 FRONT RUNNER VEHICLE OUTFITTERS
3
FIT AND SECURE
2
2.1
2.2
2.3
Ensure that the two pieces of Pinch Weld are
assembled to the edges of the Ladder Top
and the Clamp as shown.
Assemble the three Ladder Rungs and
Support Bracket (Item 3 & 4) to the Ladder
Sides (Item 1) using M6 x 16 Flange Button
Head Bolts, M6 Nyloc Nuts and M6 x 25
Thread Forming Screws (Items 10, 11 & 12)
as shown.
Place M6 Nut Caps (Item 20) on all the Nyloc
Nuts.
10mm
Assemble the Ladder Top Assembly from
2.1 to the Ladder Sides using M6 x 16
Flange Button Head Bolts and M6 Nyloc Nuts
(Items 11 & 12) as shown.
Place M6 Nut Caps (Item 20) on all the Nyloc
Nuts.
20 12
11
10
1
4
11
2
12
20
11
Torx
T30
10mm
Torx
T30
3
Apply a little anti-seize on screw
threads before inserting. Note these are
thread forming screws.
Note:
The Thread Forming Screws are used for
the Ladder Rungs

2794
4685
1.0m
0.5m
5cm
Scale: 1:25 All measurements in millimeters.
2021
1790
1992
2794
4685
1.0m
0.5m
5cm
Scale: 1:25 All measurements in millimeters.
LALD009_REV_A00 © 2022 FRONT RUNNER VEHICLE OUTFITTERS
4
FIT AND SECURE
2
2.4
2.5
2.6
Loosely insert two M6 x 60 Cap Screws with
M6 SS Spring Washers and M6 x 19 x 1SS
Flat Washers (Items 22, 23 & 24) through the
Clamp (A) into the Ladder Top (Item 2) as
shown.
Swing open the Clamp. Fit the top asembly
into vehicle's gutter.
Align the Ladder with the edge of the door.
Inside the vehicle, remove the left rear
window cover and speaker box.
Check door clearance and make sure the
ladder is aligned straight with the door.
Mark the bottom two holes of the Ladder on
the vehicle's body and remove the Ladder.
Using a drilling machine and a 6mm drill
bit, drill two pilot holes on your markings.
Change to a 8.5mm drill bit and drill the
holes to 8.5mm.
5mm
Place the ladder back onto the vehicle and
line up the holes in the bottom of the Ladder
with the holes drilled in 2.5.
Insert two M8 x 35 Hex Bolts (Item 5)
through the holes in the Ladder. Place the
two M8 PVC Washers (Item 6) between the
ladder and the vehicle, place the other two
on the inside of the vehicle. Fit the M8 Flat
Washers (Item 7) and secure with the M8
Nyloc Nuts (Item 8).
Fully tighten the two M6 x 60 Cap Screws
clamping the Ladder to the gutter.
Refit the rear window and speaker box cover
removed in 2.5.
Place M8 Nut Caps (Item 9) on the bolt
heads.
22
23
24
6 6 7
8
9
5
A
6mm
8.5mm
13mm
13mm

2021
1790
1992
1790
1992
BA
LALD009_REV_A00 © 2022 FRONT RUNNER VEHICLE OUTFITTERS
5
FIT AND SECURE2
2.7
2.8
2.9
Remove the two orginal bolts from the
bumper (A + B) and place the Bottom step
(Item 13) against the body, and align with
the two holes in the bumper as shown.
Refer to 2.7 and insert the M10 x 80 Hex
Bolt (Item 14) into the right hole marked
"A". Behind the bumper insert the Spacer
(Item 16) between the bumper and the "Tab"
attached to the body/bumper. Guide the Hex
Bolt through the Spacer and loosely fasten
using a M10 x 30 x 3 Flat Washer and M10
Nyloc Nut (Item 18 & 19).
For the left side marked "B", insert the M10
x 80 Hex Bolt & loosely fasten using a M10
Flat Washer and M10 Nyloc Nut (Item 17
& 19). If the original bolt went through the
chassis and the seat belt support bar, use
the M10 x 100 Hex Bolt (Item 15).
Align the Bottom step and Fully tighten all
bolts.
14
13
17
19
15
14
16
18
19
17mm
17mm

LALD009_REV_A00 © 2022 FRONT RUNNER VEHICLE OUTFITTERS 6
INSTALL OTHER VEHICLE AND RACK ACCESSORIES
4
Now's the time to visit your favorite Front Runner Dealer in person or online.
Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters #BornToRoam
Share your adventures on:
FINISH
3
Congratulations! You did it. Take a step back and admire your work!