FUFU & GAGA WSD22028 User manual

Version:09/23/2022 1/15
Display Stand

2/15
please read the entire manual before starting to assemble
and/or using this product.follow the manual thoroughly and
keep it for further reference.
IMPORTANT INFORMATION!
It is important that any product which is assembled using any kind of screw is re-tightened
2 weeks after assembly,and once every 3 months - in order to assure stability through-out
the lifespan of the product.
For regular maintenance and cleaning of the product, for the frame, please use a rag dipped
in neutral detergent to fully wipe it, and then dry it with a clean rag.For glass materials, wipe
with a rag dampened with water glass cleaner, and then dry with a dry rag.
Do not use an electric screwdriver, and do not use too much force when installing, because
the board is easy to break.
IMPORTANT !
Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure
to use the wall attachment, if not included with this product. Please purchase the wall
attachment that fit your wall. If unsure, seek professional advice. Please read and follow each
step of the instructions carefully.
ANTI-TOPPLE WARNING !
Try to find a partner to install
with you, which can speed up
the installation efficiency and
shorten the time.
IMPROVE EFFICIENCY !
In order to avoid scratching this
furnuture should be assembled
on a soft layer-could be a rug.
AVOID SCRATCHES!

3/15
Ax6 Ax6
Ø6x35mm
Ø4x14mm
Ø15x10mm
Cx22(+2) Dx20(+2)
Ø6x30mm Ø4x40mm
Ex48(+3) Fx8 Gx4 Hx8
Ix12(+1) Jx2 Kx2 Lx4
Please prepare the following tools
When installing, please carefully confirm whether
each screw corresponds to the manual, accessories
with similar shapes can be distinguished by size
K-1 K-2 K-3J-1 J-2 J-3
Ø3x12mm
G-1 G-2
Mx28(+2) Nx16(+1) Ox5

4/15
1
11
12
17
2
3
4
6
9
7
15
10
14
13
18
8
5
5
16
16
15

5/15
1Ax2
2
Insert quickfit screw(A) into
corresponding holes in No.9 plate
with a screwdriver as shown.
Ø6x35mm
A
9
Bx2 Cx2
Ø15x10mm Ø6x30mm
IIIIII
Connect No.10 with No.9 plate using
wooden dowel(C) and turn cam lock(B)
clockwise to tighten as shown.
A
A
C
B
C
B
9
10
C
B

6/15
3
4
Connect the component
with No.8 plate using
wooden dowel(C),
and fix with screw(D)
as shown.
Use sticker(N) to cover
screws.
Cx2
Ø6x30mm
Dx4
Ø4x40mm
Nx4
D
D
C
C
D
N
DN
N
N
9
10
8
DD
D
DC
C
N
N
N
N
Cx2
Ø6x30mm
Dx4
Ø4x40mm
Nx4
Connect No.7 plate with the
component using wooden
dowel(C), and fix with screw(D)
as shown.
Use sticker(N) to cover screws.
D
N
D
N
9
10
7

7/15
5
6Cx4
Ø6x30mm
Dx4
Ø4x40mm
Nx4
Cx4
Ø6x30mm
Dx4
Ø4x40mm
Nx4
C
C
N
N
D
D
C
C
4
2
3
N
D
N
D
C
C
C
C
ND
ND
ND
ND
1
2
3
Connect No.2 and No.3
plate with No.4 using
wooden dowel(C),then fix
with screw(D) as shown.
Cover No.1 to No.2 and No.3 plate
using wooden dowel(C) and
fix with screw(D) as shown.
N
D
D
N
Use sticker(N) to cover screws.
Use sticker(N) to cover screws.

8/15
7
Cx4
Ø6x30mm
Dx4
Ø4x40mm
8
A
Ax4
Ø6x35mm
A
A
A
A
6
D
D
D
D
D
C
C
C
C6
3
2
Attach No.6 to No.2 and No.3 plate
using wooden dowel(C)
and fix with screw(D)
as shown.
Insert quickfit screw(A) into
corresponding holes in No.6 plate
with a screwdriver as shown.

6
9/15
9
Bx4 Cx4
Ø15x10mm Ø6x30mm
B
C
IIIIII
CC
CC
B
B
B
B
7
8
Connect the two assembled components
with wooden dowel(C) and turn cam lock(B)
clockwise to tighten as shown.
Recommend more than 2 people to assemble!

10/15
10 Ø3x12mm
Ix12 Kx2 Lx4 Mx28 Ox5
K-1 K-2 K-3
M
M
M
M
L
L
L
L
M
I
I
M
M
M
M
M
I
M
M
M
M
I
I
I
M
M
M
M
M
I
M
M
M
M
I
I
M
M
M
M
MM
K-2
K-3
K-1
K-2
K-3
K-1
K-2
K-3
K-1
M
L
II
17
12 11
18
14 13
II
O
O
O
O
O
O
Fix No.11, No.17, No,13 and No.18 back plate
with screw(I) and nail(M) as shown.
Please note No.11, No.17 plate are connected
with No.12; No.13, No.18 plate are connected
with No.14.
Fix No.11, No.17, No,13 and No.18 plate together
using iron sheet(L) with nail(M) as shown.
Knock foot peg(O) into
Fix part(K-1) to back plate with washer(K-2) and
screw (K-3) as shown.
the bottom.