FUFU & GAGA WFKF210095 User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
‐ Unit can tip over causing severe injury or death.
‐ Anchor unit to stud in wall (if instructed to).
‐ Do Not allow children to climb on unit.
‐ Put heavy items on lower shelves or drawers.
Assembly Di�culty Meter
Easy Tough

Helpful Hints
PEOPLE NEEDED FOR ASSEMBLY: 1 - 2
ESTIMATED ASSEMBLY TIME: 1 HOUR
‐ Open your item in the area you plan to keep it to avoid excessive heavy lifting.
‐ Identify, sort and count the parts before attempting assembly.
‐ Compression dowels are lightly tapped in with a hammer.
‐ Slides are labeled with a R (right) and L (left) for proper placement.
‐ Make sure to always face the point on the top of the Cam Lock towards the outer edge.
‐ Use all the nails provided for the back panel and spread them out equally.
‐ Back panel must be used to make sure your unit is sturdy.
‐ Do NOT use harsh chemicals or abrasive cleaners on this item.
‐ Never push, pull, or drag your furniture.

Before You Start
‐ Read through each step carefully and follow the proper order
‐ Separate and count all your parts and hardware
‐ Give yourself enough room for the assembly process
‐ Have the following tools: Hammer
‐ Caution: If using a power drill or power screwdriver for screwing,
please be aware to slow down and stop when screw is tight.
Failure to do so may result in stripping the screw.

A B C D E
FG H I
1
2 3
Parts assembly diagram
10
87 15
8
15
5
87

installation drawing 1
55
4040
A
A
A B
B
B
FI
1
3
1
2I
2
1
1
1.Screw A into the corresponding
hole of No. 3plate, then insert
No. 1 plate into A, and finally
lock A with B
2.Screw A into the corresponding
hole of No. 2 plate, then insert
No. 1 plate into A, and finally
lock A with B
3
3.Align the sheet with the slot of
plate 1 and push it forward
4.Screw A into the corresponding
hole of No. 2 plate, then connect
No. 2 plate with the previously
installed part, and finally
lock A with B for fixation
5.Fix I in front of
plate 2 with F
The installation steps of
other drawers are the same
F

1
1
3
1
1
3
2
1
1
4
5
2
A
A
B
F
I
First install the drawer .
installation drawing 2
1
1
5
6
A
A
F
IB
Screw in the eccentric screw
on the 2 and 3 plates first
The sheet needs to be aligned
with the slot
Screw in the eccentric
screw on the 5 and 6
plates first

X2
1
1
5
1
1
4
6
9
9
7
8
7
A
A
B
F
I
First install the drawer .
installation drawing 3
9
9
7
8
A
A
F
F
I
I
B
Screw in the eccentric
screw on the 4 and 6
plates first
Screw in the eccentric screw
on the 7 and 8 plates first

1.Place B in the corresponding
position of plate 13 and plate 14
When placing B, it should be
noted that the round hole
should be aligned with the
direction of screw in A
2.Connect and fix plates 10, 11,
15 and 16 with A
installation drawing 4
B
A
Second install the cabinet.
C
D
44
11
10
18
17
When placing D, it should be
noted that the round hole
should be aligned with the
direction of screw in C
12
17
14
13
15
18
11 10
16
C
D
D
D
C
A
C D
44
C
19
19
B

A
13
12
installation drawing 5
A
12
16
16
AB
14
16
B
B
B
B
D
A
11
C D
1 1
15 11
C
Install Nos. 12
,
13,14,15 and 16
using A and B
as shown in the
picture.
Note that the
screws are
hidden below
and on the
back
Tighten all B's
as shown
Install using C
and D between No.
15 and
No. 16 and tighten
the screws

installation drawing 6
Insert the sheet along
the grooves as shown