Fuji Electric MICREX-SX series User manual

FEH206b
series
USER’S MANUAL
High-speed Multi-range Analog Module
8Ch Voltage Input <Type: NP1AXH8V-MR>
8Ch Current Input <Type: NP1AXH8I-MR>
8Ch Voltage Output <Type: NP1AYH8V-MR>
8Ch Current Output <Type: NP1AYH8I-MR>
4Ch Voltage Output <Type: NP1AYH4V-MR>
4Ch Current Output <Type: NP1AYH4I-MR>
6Ch Input/Output <Type: NP1AWH6-MR>

Preface
This user's manual describes the system configuration, specifications and operating method of the following modules for
MICREX-SX series:
Multi-range analog 8ch voltage input module (type: NP1AXH8V-MR)
Multi-range analog 8ch current input module (type: NP1AXH8I-MR)
Multi-range analog 8ch voltage output module (type: NP1AYH8V-MR)
Multi-range analog 8ch current output module (type: NP1AYH8I-MR)
Multi-range analog 4ch voltage output module (type: NP1AYH4V-MR)
Multi-range analog 4ch current output module (type: NP1AYH4I-MR)
Multi-range analog 6ch input/output module (type: NP1AWH6-MR)
Read this manual carefully to ensure correct operation. When using modules or peripheral devices, be sure to read the
corresponding user's manuals listed below:
<SX-Programmer Expert (D300win)>
Title Manual No. Contents
User's Manual Instruction, MICREX-SX series FEH200 Explains the memory, language and system definitions of the
MICREX-SX series.
User's Manual Hardware,
MICREX-SX series SPH FEH201 Explains the system configuration, the specifications and operations of modules in the MICREX-SX series.
User's Manual D300win <Reference>,
MICREX-SX series FEH257 Explains the methods for installing, the functions and the operations of D300winV3.
User's Manual D300win <LD/FBD Editor>,
MICREX-SX series FEH257-1 Explains the operations of LD/FBD added to D300winV3.
<SX-Programmer Standard (Standard loader)>
* This manual is structured such that you can consult it, whether you use SX-Programmer Expert (D300win ) or SX-programmer
standard (Standard loader).
* In addition to the above manuals, the following Fuji Electric FA Components & Systems Co., Ltd. site offers various manuals
and technical documents associated with MICREX-SX.
URL http://www.fujielectric.co.jp/fcs/eng/
Notes
1. This manual may not be reproduced in whole or part in any form without prior written approval by the manufacturer.
2. The contents of this manual (including specifications) are subject to change without prior notice.
3. If you find any ambiguous or incorrect descriptions in this manual, please write them down (along with the manual No.
shown on the cover) and contact FUJI.
Title Manual No. Contents
User's Manual Instruction, MICREX-SX series FEH588 Explains the memory, language and system definitions of the
MICREX-SX series.
User's Manual Hardware,
MICREX-SX series SPH FEH201 Explains the system configuration, the specifications and operations of modules in the MICREX-SX series.
User's Manual SX-Programmer Standard
<Reference>, MICREX-SX series FEH590 Explains the functions and the operations of SX-Programmer Standard.

Safety Precautions
Be sure to read the "Safety Precautions" thoroughly before using the module.
Here, the safety precautions items are classified into "Warning" and "Caution".
Warning
Caution
: Incorrect handling of the device may result in death or serious injury.
: Incorrect handling of the device may result in minor injury or physical damage.
Even some items indicated by "Caution" may result in a serious accident.
Both safety instruction categories provide important information. Be sure to strictly observe these instructions.
The items to be cared most are shown below:
Warning





Never touch any part of charged circuits as terminals and exposed metal portion while the power is turned ON. It may
result in an electric shock to the operator.
Turn OFF the power before mounting, dismounting, wiring, maintaining or checking, otherwise, electric shock, erratic
operation or troubles might occur.
Place the emergency stop circuit, interlock circuit or the like for safety outside the PLC. A failure of PLC might break or
cause problems to the machine.
Do not connect in reverse polarity, charge (except rechargeable ones), disassemble, heat, deform, throw in a fire or
short-circuit the batteries, otherwise, they might burst or take fire.
If batteries have any deformation, spilled fluids, or other abnormality, do not use them. The use of such batteries might
cause explosion or firing.

Safety Precautions
Caution

























Do not use one found damaged or deformed when unpacked, otherwise, fire, failure or erratic operation might be caused.
Do not shock the product by dropping or tipping it over, otherwise, it might be damaged or troubled.
Follow the directions of the operating instructions and manual when mounting the product.
If mounting is improper, the product might drop or develop problems or erratic operations.
Use the rated voltage and current mentioned in the operating instructions and manual. Use beyond the rated values
might cause fire, erratic operation or failure.
Operate (keep) in the environment specified in the operating instructions and manual. High temperature, high humidity,
condensation, dust, corrosive gases, oil, organic solvents, excessive vibration or shock might cause electric shock, fire,
erratic operation or failure.
Select a wire size to suit the applied voltage and carrying current. Tighten the wire terminals to the specified torque.
Inappropriate wiring or tightening might cause fire, malfunction or failure, or might cause the product to drop from its
mounting.
Contaminants, wiring chips, iron powder or other foreign matter must not enter the device when installing it, otherwise,
fire, accident, erratic operation or failure might occur.
Remove the dust-cover seals of modules or units after wiring, otherwise, fire, accident, erratic operation or failure might
occur.
Connect the ground terminal to the ground, otherwise, electric shock or erratic operation might occur.
Periodically make sure the terminal screws and mounting screws are securely tightened.
Operation at a loosened status might cause fire or erratic operation.
Put the furnished connector covers on unused connectors, otherwise, erratic operation or failure might occur.
Put the furnished terminal covers on the terminal blocks, otherwise, electric shock or fire might occur.
Sufficiently make sure of safety before program change, forced output, starting, stopping or anything else during a run.
Wrong operation might break or cause problems to the machine
Engage the loader connector in a correct orientation, otherwise, an erratic operation might occur.
Before touching the PLC, discharge any static electricity that may have been collected on your body. To discharge it,
touch a grounded metallic object. Static electricity might cause erratic operation or failure.
Be sure to install the electrical wiring correctly and securely, observing the directions of the operating instructions and
manual. Wrong or loose wiring might cause fire, accident or failure.
When disengaging the plug from the outlet, do not pull the cord, otherwise, break of cable might cause fire or failure.
Do not attempt to change system configurations (such as installing or removing I/O modules) while the power is ON,
otherwise, erratic operation or failure might occur.
Do not attempt to repair the module by yourself, but contact your Fuji Electric agent. When replacing the batteries,
correctly and securely connect the battery connectors, otherwise, fire, accident or failure might occur.
Do not remodel or disassemble the product, otherwise, failure might occur.
Follow the regulations of industrial wastes when the device is to be discarded.
The modules covered in these operating instructions have not been designed or manufactured for use in equipment or
systems which, in the event of failure, can lead to loss of human life.
If you intend to use the modules covered in these operating instructions for special applications, such as for nuclear
energy control, aerospace, medical or transportation, please consult your Fuji Electric agent.
Be sure to provide protective measures when using the module covered in these operating instructions in equipment
which, in the event of failure, can lead to loss of human life or other grade results.
External power supply (such as 24 V DC power supply) which is connected to DC I/O should be strongly isolated from
AC power supply. (Use of EN60950 conforming power supply is recommended.) Otherwise, accident or failure might
be caused.

Revision
*Manual No. is shown at lower right on the cove
r.
Printed on *Manual No. Revision contents
Sep. 2002 FEH206 First edition
Jun. 2004 FEH206a Operations when using SX-Programmer Standard were added.
Apr. 2006 FEH206b Specifications of Analog Input/Output Module (type: NP1AWH6-MR) were added.

Contents
Preface
Safety Precautions
Revisions
Contents
Section 1 General ....................................................................................... 1-1
1-1 List of Modules ............................................................................................................................... 1-1
1-2 Supported Versions of Program Loader ...................................................................................... 1-1
Section 2 Specifications ............................................................................ 2-1
2-1 General Specifications .................................................................................................................. 2-1
2-2 Performance Specifications.......................................................................................................... 2-2
2-2-1 8ch voltage input module ................................................................................................................... 2-2
2-2-2 8ch current input module.................................................................................................................... 2-2
2-2-3 8ch voltage output module ................................................................................................................. 2-3
2-2-4 8ch current output module.................................................................................................................. 2-3
2-2-5 4ch voltage output module ................................................................................................................. 2-4
2-2-6 4ch current output module.................................................................................................................. 2-4
2-2-7 6ch input/output module..................................................................................................................... 2-5
2-3 Conversion Characteristics ........................................................................................................... 2-6
2-3-1 Conversion characteristics of analog voltage input .......................................................................... 2-6
2-3-2 Conversion characteristics of analog current input .......................................................................... 2-8
2-3-3 Conversion characteristics of analog voltage output ...................................................................... 2-10
2-3-4 Conversion characteristics of analog current output ...................................................................... 2-12
2-4 Functional Specifications.............................................................................................................2-13
2-4-1 Analog input module functions ........................................................................................................ 2-13
2-4-2 Analog output module functions ...................................................................................................... 2-14
2-4-3 Analog input/output module functions ............................................................................................. 2-15
2-5 Names and Functions ...................................................................................................................2-16
2-5-1 Analog input module (NP1AXH8V-MR/NP1AXH8I-MR) ................................................................... 2-16
2-5-2 Analog output module (NP1AYH8V-MR, NP1AYH8I-MR, NP1AYH4V-MR, NP1AYH4I-MR) ............. 2-18
2-5-3 Analog input/output module (NP1AWH6-MR).................................................................................. 2-21
2-6 Dimensions ....................................................................................................................................2-23
Section 3 System Configuration............................................................... 3-1
3-1 Mounting on the Base Board ........................................................................................................ 3-1
3-1-1 Mounting position ............................................................................................................................... 3-1
3-1-2 Number of mountable modules......................................................................................................... 3-1
Section 4 Software Interface ..................................................................... 4-1
4-1 Analog Input Module ..................................................................................................................... 4-1
4-1-1 Memory allocation in Switch Batch Setting mode.............................................................................. 4-1
4-1-2 Memory allocation in Software Set Range Operation mode............................................................. 4-2
4-2 Analog Output Module..................................................................................................................4-14
4-2-1 Memory allocation in Switch Batch Setting mode............................................................................ 4-14
4-2-2 Memory allocation in Software Set Range Operation mode........................................................... 4-16
4-3 Analog Input/Output Module........................................................................................................4-26
4-3-1 Memory allocation in Switch Batch Setting mode............................................................................ 4-26
4-3-2 Memory allocation in Software Set Range Operation mode........................................................... 4-27
Page

Contents
Page
Section 5 Wiring .......................................................................................... 5-1
5-1 Wiring of Analog Input Module .................................................................................................... 5-1
5-1-1 Terminal arrangement........................................................................................................................ 5-1
5-1-2 Wiring example ................................................................................................................................... 5-2
5-2 Wiring of Analog Output Module.................................................................................................. 5-3
5-2-1 Terminal arrangement........................................................................................................................ 5-3
5-2-2 Wiring example ................................................................................................................................... 5-4
5-3 Wiring of Analog Input/Output Module ........................................................................................ 5-5
5-2-1 Terminal arrangement........................................................................................................................ 5-5
5-2-2 Wiring example ................................................................................................................................. 5-46
Appendix 1 Offset/Gain Adjustment <D300win>.............................. App.1-1
Appendix 1-1 Offset/Gain Adjustment of Analog Input Module ...............................................App.1-1
Appendix 1-2 Offset/Gain Adjustment of Analog Output Module.............................................App.1-6
Appendix 2 Offset/Gain Adjustment <SX-Programmer Standard>............ App.2-1
Appendix 2-1 Offset/Gain Adjustment of Analog Input Module ...............................................App.2-1
Appendix 2-2 Offset/Gain Adjustment of Analog Output Module.............................................App.2-6

1-1
Section 1 General
Analog modules listed below are described in this manual.
1-2 Supported Versions of Program Loader
Type Analog voltage input
0to5V,1to5V,
0 to 10V, -10 to 10V
Analog current input
4 to 20mA, 0 to 20mA,
-20 to 20mA
Analog voltage output
0to5V,1to5V,
0 to 10V, -10 to 10V
Analog current output
0 to 20mA, 4 to 20mA
NP1AXH8V-MR 8 channels - - -
NP1AXH8I-MR - 8 channels - -
NP1AYH8VMR - - 8 channels -
NP1AYH8I-MR - - - 8 channels
NP1AYH4V-MR - - 4 channels -
NP1AYH4I-MR---4channels
NP1AWH6-MR 4 channels 2 channels
Type D300winV2
NP4H-SEDBV2
SX-Programmer Expert
D300winV3
NP4H-SEDBV3
SX-Programmer Standard
NP4H-SWN
NP1AXH8V-MR
V2.2.0.0 or later V3.0.0.0 or later V2.0.0.0 or later
NP1AXH8I-MR
NP1AYH8VMR
NP1AYH8I-MR
NP1AYH4V-MR
NP1AYH4I-MR
NP1AWH6-MR - V3.3.3.0 or later V2.2.3.0 or later
1-1 List of Modules

2-1
Section 2 Specifications
2-1 General Specifications
Item Specification
Physical
environmental
conditions
Operating ambient
temperature 0to+55
Storage (transportation)
temperature -20to70
Relative humidity 20 to 95%RH, no condensation
Pollution degree 2 (no condensation)
Corrosion immunity Free from corrosive gases. Not stained with organic solvents
Corrosive gas Free from corrosive gases.
Operating altitude 2000 m or less above sea level
Transport condition: 70 kPa (equivalent to 3000 m above sea level) or more
Mechanical
service
conditions
Vibration Half amplitude: 0.15 mm, Constant acceleration: 19.6 m/s
2
2 hours in each of X, Yand Z directions, total 6 hours
Shock Peak acceleration: 147 m/s
2
(3 cycles in each direction)
Electrical
service
conditions
Noise immunity Rise time 1 ns, pulse width 1 μs,1.5kV(noisesimulator)
Electrostatic discharge Contact discharge: 6 kV, Aerial discharge: 8 kV
Radioelectromagnetic field 10 V/m (80 MHz to 1,000 MHz)
Isolation method Between external terminal and internal logic circuit:
photocoupler (signal), isolated power supply(DC/DC converter)
Between channels: Not insulated
Dielectric strength 500 V AC, 1 minute (betweenexternal wires connected together and ground)
Insulation resistance 10 MΩor more with 500 V DC megger (between external wires connected
together and ground)
Internal current
consumption Analog input NP1AXH8V-RM: 24 V DC, max. 200 mA (supplied from the power module) NP1AXH8I-RM: 24 V DC, max. 200 mA (supplied from the power module)
Analog output NP1AYH8V-RM: 24 V DC, max. 240 mA (supplied from the power module)
NP1AYH8I-RM: 24 V DC, max. 300 mA (supplied from the power module)
NP1AYH4V-RM: 24 V DC, max. 200 mA (supplied from the power module)
NP1AYH4I-RM: 24 V DC, max. 200 mA (supplied from the power module)
Analog input/output NP1AWH6-MR: 24V DC, max. 200mA (supplied from the power module)
Installation
conditions Structure Panel built in type, IP30
Cooling method Natural air cooled
Mass Analog input NP1AXH8V-RM: approx. 240 g
NP1AXH8I-RM: approx. 240 g
Analog output NP1AYH8V-RM: approx. 240 g
NP1AYH8I-RM: approx. 240 g
NP1AYH4V-RM: approx. 240 g
NP1AYH4I-RM: approx. 240 g
Analog input/output NP1AWH6-MR: approx. 240g
Outside dimensions W35*H105*D111 mm (protrusion 21 mm)

Section 2 Specifications
2-2
Item Specification
Type NP1AXH8V-MR
No. of input points 8
Analoginputrange 0to5V 1to5V 0to10V -10to10V
Input impedance 1 MΩ
Maximum allowable input 15 V
Maximum resolution 1.25 mV 1.25 mV 1.25 mV 1.25 mV
Digital output value (INT type) 0 to 16000 -8000 to 8000
Measurement accuracy Ambient temperature 18 to 28 : 0.1% (of full scale)
Ambient temperature 0 to 55 : 0.2% (of full scale) (See note 1.)
Sampling time 0.27 ms x (Number of conversion enabled channels + 1)
Input filtering time Max. approx. 100 μs(hardfilter)
Input delay time Max. 2.5 ms/8 points + takt time (ms)
External connecting method Detachable terminal block: M3 screw, 20 poles
For the signal assignment of terminals, refer to "Section 5 Wiring".
Cable to use Be sure to use shielded twisted pair cable.
Treatment of unused input To basically be short-circuited
No. of occupied slots 1 (one)
No. of occupied words Input: 8 words, output: 4 words (fixed)
2-2 Performance Specifications
2-2-1 8ch voltage input module
Note: For the range of 1 to 5 V, 0.3% (of full scale) when ambient temperature is 0 to 55 .
2-2-2 8ch current input module
Item Specification
Type NP1AXH8I-MR
No. of input points 8
Analog input range 4 to 20 mA 0 to 20 mA -20 to 20 mA
Input impedance 250 Ω
Maximum allowable input 30 mA
Maximum resolution 2.5 μA
Digital output value (INT type) 0 to 16000
Measurement accuracy Ambient temperature 18 to 28 : 0.1% (of full scale)
Ambient temperature 0 to 55 : 0.4% (of full scale)
Sampling time 0.27 ms x (Number of conversion enabled channels + 1)
Input filtering time Max. approx. 100 μs (hard filter: time constant of primary delay)
Input response time Max. 2.5 ms/8 points + takt time
External connecting method Detachable terminal block: M3 screw, 20 poles
For the signal assignment of terminals, refer to "Section 5 Wiring".
Cable to use Be sure to use shielded twisted pair cable.
Treatment of unused input To basically be short-circuited
No. of occupied slots 1 (one)
No. of occupied words Input: 8 words, output: 4 words (fixed)

2-3
Section 2 Specifications
2-2 Performance Specifications
2-2-3 8ch voltage output module
Item Specification
Type NP1AYH8V-MR
No. of output points 8
Analogoutputrange 0to5V 1to5V 0to10V -10to10V
External load resistance Min. 500ΩMin. 500ΩMin. 1kΩMin. 1kΩ
Maximum resolution 1.25 mV 1.25 mV 1.25 mV 1.25 mV
Digital input value (INT type) 0 to 16000 -8000 to 8000
Measurement accuracy Ambient temperature 18 to 28 : 0.1% (of full scale)
Ambient temperature 0 to 55 : 0.2% (of full scale) (See note 1.)
Output response time Max. 2.0 ms + takt time (ms)
Max. 1.0 ms + takt time (ms) when output is disabled for channels 5 to 8
Load short-circuit protection Provided. (See note 2.)
External connecting method Detachable terminal block: M3 screw, 20 poles
For the signal assignment of terminals, refer to "Section 5 Wiring".
Cable to use Be sure to use shielded twisted pair cable.
Treatment of unused output To basically be opened
No. of occupied slots 1 (one)
No. of occupied words Input: 4 words, output: 8 words (fixed)
Note 1: For the range of 1 to 5 V, 0.3% (of full scale) when ambient temperature is 0 to 55 .
Note 2: Short-circuit protection for arbitrary one channel. The occurrence of short-circuit on multiple channels in an environment
where ambient temperature is higher than 30 may have a bad influence on internal electronic component of the
module.
2-2-4 8ch current output module
Item Specification
Type NP1AYH8I-MR
No. of output points 8
Analog output range 0 to 20 mA 4 to 20 mA
External load resistance Max. 600Ω
Maximum resolution 2.5 μA
Digital input value (INT type) 0 to 16000
Measurement accuracy Ambient temperature 18 to 28 : 0.1% (of full scale)
Ambient temperature 0 to 55 : 0.4% (of full scale)
Output response time Max. 2.0 ms + takt time (ms)
Max. 1.0 ms + takt time (ms) when output is disabled for channels 5 to 8
External connecting method Detachable terminal block: M3 screw, 20 poles
For the signal assignment of terminals, refer to "Section 5 Wiring".
Cable to use Be sure to use shielded twisted pair cable.
Treatment of unused output To basically be short-circuited
No. of occupied slots 1 (one)
No. of occupied words Input: 4 words, output: 8 words (fixed)

Section 2 Specifications
2-4
2-2 Performance Specifications
2-2-5 4ch voltage output module
Item Specification
Type NP1AYH4V-MR
No. of output points 4
Analogoutputrange 0to5V 1to5V 0to10V -10to10V
External load resistance Min. 500ΩMin. 500ΩMin. 1kΩMin. 1kΩ
Maximum resolution 1.25 mV 1.25 mV 1.25 mV 1.25 mV
Digital input value (INT type) 0 to 16000 -8000 to 8000
Measurement accuracy Ambient temperature 18 to 28 : 0.1% (of full scale)
Ambient temperature 0 to 55 : 0.2% (of full scale) (See note 1.)
Output response time Max. 1.0 ms + takt time (ms)
Load short-circuit protection Provided. (See note 2.)
External connecting method Detachable terminal block: M3 screw, 10 poles
For the signal assignment of terminals, refer to "Section 5 Wiring".
Cable to use Be sure to use shielded twisted pair cable.
Treatment of unused output To basically be opened
No. of occupied slots 1 (one)
No. of occupied words Input: 4 words, output: 4 words (fixed)
Item Specification
Type NP1AYH4I-MR
No. of output points 4
Analog output range 0 to 20 mA 4 to 20 mA
External load resistance Max. 600Ω
Maximum resolution 2.5 μA
Digital input value (INT type) 0 to 16000
Measurement accuracy Ambient temperature 18 to 28 : 0.1% (of full scale)
Ambient temperature 0 to 55 : 0.4% (of full scale)
Output response time Max. 1.0 ms + takt time (ms)
External connecting method Detachable terminal block: M3 screw, 10 poles
For the signal assignment of terminals, refer to "Section 5 Wiring".
Cable to use Be sure to use shielded twisted pair cable.
Treatment of unused output To basically be short-circuited
No. of occupied slots 1 (one)
No. of occupied words Input: 4 words, output: 4 words (fixed)
Note 1: For the range of 1 to 5 V, 0.3% (of full scale) when ambient temperature is 0 to 55 .
Note 2: Short-circuit protection for arbitrary one channel. The occurrence of short-circuit on multiple channels in an environment
where ambient temperature is higher than 30 may have a bad influence on internal electronic component of the
module.
2-2-6 4ch current output module

2-5
Section 2 Specifications
Note 1: Short-circuit protection for arbitrary one channel. The occurrence of short-circuit on multiple channels in an environment
where ambient temperature is higher than 30 may have a bad influence on internal electronic component of the
module.
Note 2: For the range of 4 to 20 mA and 0 to 20 mA, 0.3% (of full scale) when ambient temperature is 0 to 55 .
2-2 Performance Specifications
2-2-7 6ch input/output module
Item Specification
Type NP1AWH6-MR
Analog
input
No. of input points 4
Analog input range 0 to 5V, 1 to 5V, 0 to 10V, -10 to 10V 0 to 20mA, 4 to 20mA, -20 to 20mA
Input impedance 1 MΩ250 Ω
Maximum allowable input 15 V 30 mA
Maximum resolution 0.625 mV 2.5 μA
Digital output value (INT type) 0 to 16000, -8000 to 8000
Sampling time 0.25 ms x (Number of conversion enabled channels + 1)
Input filtering time Max. approx. 47 μs (hard filter: time constant of primary delay)
Input delay time Max. 1.0 ms/4 channels + takt time (ms)
Analog
output
No. of output points 2
Analog output range 0 to 5V, 1 to 5V, 0 to 10V, -10 to 10V 0 to 20mA, 4 to 20mA
External load resistance Min. 2 kΩMax. 500 Ω
Maximum resolution 0.625 mV 2.5 μA
Digital input value (INT type) 0 to 16000, -8000 to 8000
Output response time Max. 0.5 ms + takt time (ms)
Load short-circuit protection Provided (voltage output) (See note 1.)
Measurement accuracy Ambient temperature 18 to 28 : 0.1% (of full scale)
Ambient temperature 0 to 55 : 0.2% (of full scale) (See note 2.)
External connecting method Detachable terminal block: M3 screw, 10 poles
For the signal assignment of terminals, refer to "Section 5 Wiring".
Cable to use Be sure to use shielded twisted pair cable.
Treatment of unused input Input: To basically be short-circuited (between V+ and COM)
Output: To basically be opened
No. of occupied slots 1 (one)
No. of occupied words Input: 4 words, Output: 4 words (fixed)

Section 2 Specifications
2-6
Analog input
voltage (V)
Digital output value
(INT type)
(10250) 16400
(10000) 16000
Practicable digital
output range
(-250) -400
0.9
0
15 5.1
(Note)
Gain value
Offset value
2-3 Conversion Characteristics
2-3-1 Conversion characteristics of analog voltage input
Output range Digital input range
0 to 5 V 0 to 16000 0 to 10000
1 to 5 V 0 to 16000 0 to 10000
0 to 10 V 0 to 16000 0 to 10000
-10 to 10 V -8000 to 8000 0 to 10000
1) Characteristic curve for the input range of 0 to 5 V
2) Characteristic curve for the input range of 1 to 5 V
Note: Parenthesized figures mean the values when the unit of digital output value is % in Fixed Range Operation mode (excl.
NP1AWH6-MR). In software Set Range Operation mode, scaling is necessary to express output values by the %.
Analog input voltage (V)
Digital output value
(INT type)
(10250) 16400
(10000) 16000
Practicable digital
output range
-400 (-250)
-0.125
5 5.125
(Note)
Gain value
Offset value
0
Analog input
voltage (V)
Digital output value
(INT type)
16400
16000
Practicable digital
output range
-4000
0
15 5.1
Gain value
Offset value
<NP1AWH6-MR only>

2-7
Section 2 Specifications
3) Characteristic curve for the input range of 0 to 10 V
4) Characteristic curve for the input range of -10 to 10 V
2-3 Conversion Characteristics
Analog input voltage (V)
Digital output value
(INT type)
(10250) 16400
(10000) 16000
Practicable digital
output range
-400 (-250)
-0.25
10 10.25
(Note)
Gain value
Offset value
0
Analog input voltage (V)
Digital output value
(INT type)
(10125) 8200
(10000) 8000
Practicable digital
output range
-8000 (0)
-8200 (-125)
-10.25 -10
10 10.25
(Note)
Gain value
Offset value
0
Note: Parenthesized figures mean the values when the unit of digital output value is % in Fixed Range Operation mode (excl.
NP1AWH6-MR). In software Set Range Operation mode, scaling is necessary to express output values by the %.

Section 2 Specifications
2-8
2-3-2 Conversion characteristics of analog current input
Input range Digital output range
4 to 20 mA 0 to 16000 0 to 10000
0 to 20 mA 0 to 16000 0 to 10000
-20 to 20 mA -8000 to 8000 0 to 10000
1) Characteristic curve for the input range of 4 to 20 mA
2) Characteristic curve for the input range of 0 to 20 mA
2-3 Conversion Characteristics
Analog input current (mA)
Digital output value
(INT type)
(10250) 16400
(10000) 16000
Practicable digital
output range
(-250) -400
3.6
420 20.4
(Note)
Gain value
0
Offset value
Analog input current (mA)
Digital output value
(INT type)
(10250) 16400
(10000) 16000
Practicable digital
output range
-400 (-250)
-0.5
20 20.5
(Note)
Gain value
0
Offset value
Note: Parenthesized figures mean the values when the unit of digital output value is % in Fixed Range Operation mode (excl.
NP1AWH6-MR). In software Set Range Operation mode, scaling is necessary to express output values by the %.

2-9
Section 2 Specifications
3) Characteristic curve for the input range of -20 to 20 mA
2-3 Conversion Characteristics
Digital output value
(INT type)
(10125) 8200
(10000) 8000
-8200 (-125)
-8000 (0)
20 20.5
-20.5 -20
(Note)
Gain value
0Analog input current (mA)
Practicable digital
output range
Offset value
Note: Parenthesized figures mean the values when the unit of digital output value is % in Fixed Range Operation mode (excl.
NP1AWH6-MR). In software Set Range Operation mode, scaling is necessary to express output values by the %.

Section 2 Specifications
2-10
2-3-3 Conversion characteristics of analog voltag output
Output range Digital input range
0 to 5 V 0 to 16000 0 to 10000
1 to 5 V 0 to 16000 0 to 10000
0 to 10 V 0 to 16000 0 to 10000
-10 to 10 V -8000 to 8000 -
1) Characteristic curve for the output range of 0 to 5 V
2) Characteristic curve for the output range of 1 to 5 V
Note 1: Parenthesized figures mean the values when the unit of digital input value is % in Fixed Range Operation mode (excl.
NP1AWH6-MR). In Software Set Range Operation mode, scaling is necessary to express input values by the %.
Note 2: If parameter mode is activated in Software Set Range Operation mode, analog output value becomes equal to the
offset value.
2-3 Conversion Characteristics
Digital input value
(INT type)
Analog output voltage (V)
5.125
5
Practicable analog
output range
(-250) -400
-0.125 16000
(10000) 16400
(10250)
(Note)
Gain value
Offset value
0
Digital input value
(INT type)
Analog output voltage (V)
Practicable analog
output range
(-250) -400
-0.9
0
1
16000
(10000)
5.1
5
16400
(10250)
(Note)
Gain value
Offset value

2-11
Section 2 Specifications
3) Characteristic curve for the output range of 0 to 10 V
4) Characteristic curve for the output range of -10 to 10 V
Note 1: Parenthesized figures mean the values when the unit of digital input value is % in Fixed Range Operation mode (excl.
NP1AWH6-MR). In Software Set Range Operation mode, scaling is necessary to express input values by the %.
Note 2: For the range of -10 to 10 V, the unit of % cannot be selected by switch setting.
Note 3: If parameter mode is activated in Software Set Range Operation mode, analog output value becomes equal to the
offset value, except that 0 V is output for the range of -10 to 10 V.
2-3 Conversion Characteristics
Digital input value
(INT type)
Analog output voltage (V)
10.25
10
Practicable analog
output range
(-250) -400
-0.25 16000
(10000) 16400
(10250)
(Note)
Gain value
Offset value
0
Digital input value
(INT type)
Analog output voltage (V)
10.25
10
Practicable analog
output range
-10.25
-10
8000
(10000)
-8000
(0)
-8200
(-125)
8200
(10125)
(Note)
Gain value
0
Offset value

Section 2 Specifications
2-12
2-3-4 Conversion characteristics of analog current output
Output range Digital input range
4 to 20 mA 0 to 16000 0 to 10000
0 to 20 mA 0 to 16000 0 to 10000
1) Characteristic curve for the output range of 4 to 20 mA
2) Characteristic curve for the output range of 0 to 20 mA
Note 1: Parenthesized figures mean the values when the unit of digital input value is % in Fixed Range Operation mode (excl.
NP1AWH6-MR). In Software Set Range Operation mode, scaling is necessary to express input values by the %.
Note 2: If parameter mode is activated in Software Set Range Operation mode, analog output value becomes equal to the
offset value.
2-3 Conversion Characteristics
Digital input value
(INT type)
Analog output current (mA)
20.4
20
Practicable analog
output range
(-250) -400
4 -3.6
16000
(10000) 16400
(10250)
(Note)
(Note)
Gain value
Offset value
0
Digital input value
(INT type)
Analog output current (mA)
20.5
20
Practicable analog
output range
0
16000
(10000) 16400
(10250)
(Note)
Gain value
Offset value