Fuji Electric OPC-E2-ADP1 User manual

- 5 -
Option Attachment "OPC-E2-ADP1"
- Please read and ensure a proper understanding of this manual before installing, connecting (wiring), operating, or con-
ducting maintenance and inspection of the interface option.
- Improper handling might result in incorrect operation, a short life, or even a failure of this product as well as the motor.
- Deliver this manual to the end user of this product. The end user should store this instruction manual safely until such time
as the product is disposed of.
Fuji Electric Co., Ltd. INR-SI47-1895-JE
Instruction Manual

- 6 -
Thank you for purchasing the option attachment "OPC-E2-ADP1".
The use of this option attachment allows the FRENIC-Ace series to be equipped with option cards (sold separately).
1. Product Check
Please check the following before using the
product.
(4) Check the model on the nameplate and
ensure that the product is the same as that
ordered.
(5) Ensure that the package contains both the
attachment and accessories.
(6) Ensure that neither the attachment nor
accessories have suffered damage such
as breakage or denting during transport.
Refer to the "1.1 Product configuration"
diagram on the right for details of the
nameplate attachment location and ac-
cessories.
If anything is out of place, or the product ap-
pears to be defective, contact your dealer or
nearest Fuji sales office.
2. Specifications
The applicable scope for this product is as follows.
(1) Applicable models
Series name Inverter capacity
FRENIC-Ace - -
- -
- -
- -
(2) No. of installable option cards: 1
3. Installation Method
Please wait at least 5 minutes after the inverter power has been turned OFF before attempting installation and
wiring.
Also ensure that the touch panel LEDs are OFF, and use a tester to confirm that the DC intermediate circuit volt-
age across main circuit terminals P(+) and N(-) has dropped to a stable value (+25 VDC or lower).
Risk of electric shock
Wire the inverter main circuit terminals and control circuit terminals before installing this attachment.
Step 1
First, wire the inverter main circuit terminals and control circuit terminals.
Step 2
Follow the installation procedure on the next page to install the attachment.
Step 3
Install the option card.
Step 4
Wire the option card to the attachment ground wire and option card terminals.
Secure the wiring near the inverter to prevent the weight of the wiring being applied to the option card.
1.1 Product configuration
Attachment
Harness
Tapping screw
(M3 x 14)
2
Screw
(M3 x 6)
1
Nameplate

- 7 -
Installation procedure [Example using option card OPC-DIO]
Ensure that all connectors have been inserted fully and are locked.
(2)
(1)
Open the top cover.
Press the indented locations (indicated
release the lock, allowing the
cover to be opened.
Step (2) details
(3)
(7)
Connect the connector on the
opposite end of the harness to
the attachment connector.
Remove the touch panel.
Remove the bottom cover.
(4)
(5)
Attach the
attachment
to the inverter.
(6)
Connect the harness to
the inverter connector
(larger side of connector).
Pass the harness
through to the inside of
the attachment.
(6)
(6)
(6)

- 8 -
Fuji Electric Co., Ltd.
Gate City Ohsaki, East Tower, 11-2, Osaki 1-chome, Shinagawa-ku, Tokyo, 141-0032, Japan
Phone: [phone] Fax: [phone]
URL http://www.fujielectric.com/
INR-SI47-1895-JE
If removing the attachment, always disconnect one side of the harness connector beforehand.
Always connect the attachment ground wire to the inverter ground to ground the inverter also.
(8)
Front view of screw tightening loca-
tions
Tighten with tapping screws.
*1
Ti *2
(9)
(10)
Align the option card with the protrusion.
Protrusion
(11)
Tighten the board securing screws. (screws pr
o-
vided with option card)
*2
Attachment
installation
complete
*1
The attachment will be temporarily secured with the
clips on the case, however,
it must be secured
properly with the tapping screws before performing
operation.
*2
The tapping screws may be deformed or damaged if
tightened with more than the specified amount of
torque.
Push the option card down in
the direction
of the arrow to fit the connec
t-
Use the screw (M3 x 6) provided to connect the ground wire to Part A .
*2 Recommended ground wire size: AWG 20 to 16 (0.5 to 1.5 mm2)
(15)
Part A
(13)
(12)
(14)