Fujitsu ETERNUS JX40 S2 User manual

ETERNUS JX40 S2
Storage Subsystem
Operating Manual
Edition August 2015

Comments…Suggestions…Corrections…
The User Documentation Department would like to
know your opinion of this manual. Your feedback helps
us optimize our documentation to suit your individual
needs.
Feel free to send us your comments by e-mail to
[email protected].
Certified documentation
according to DIN EN ISO 9001:2000
To ensure a consistently high quality standard and
user-friendliness, this documentation was created to
meet the regulations of a quality management system
which complies with the requirements of the standard
DIN EN ISO 9001:2000.
cognitas. Gesellschaft für Technik-Dokumentation mbH
www.cognitas.de
Copyright and Trademarks
© cognitas. Gesellschft für Technik-Dokumentation mbH 2015 Pfad: C:\Users\gudat\Documents\______FTS\_STORAGE\JX40_S2\FM\sx40-ba-en\sx40-ba-en.vor
Copyright © 2015 Fujitsu Technology Solutions GmbH.
All rights reserved.
Delivery subject to availability; right of technical modifications reserved.
All hardware and software names used are trademarks of their respective manufacturers.
– The contents of this manual may be revised without prior notice.
– Fujitsu assumes no liability for damages to third party copyrights or other
rights arising from the use of any information in this manual.
– No part of this manual may be reproduced in any form without the prior
written permission of Fujitsu.

ETERNUS JX40 S2 Operating Manual
Before reading this manual
For your safety
This manual contains important information for safely and correctly using this
product.
Carefully read the manual before using this product. Pay particular attention to
the accompanying manual “Safety notes and other important information” and
ensure these safety notes are understood before using the product.
Keep this manual and the manual “Safety notes and other important
information” in a safe place for easy reference while using this product.
Radio interference
This product is a “Class A” ITE (Information Technology Equipment) as defined
by the Voluntary Control Council for Interference by Information Technology
Equipment (VCCI-A) of Japan. In a domestic environment this product may
cause radio interference, in which case the user may be required to take
appropriate measures.
Aluminum electrolytic capacitors
The aluminum electrolytic capacitors used in the product's printed circuit board
assemblies and in the mouse and keyboard are limited-life components. Use of
these components beyond their operating life may result in electrolyte leakage
or depletion, potentially causing emission of foul odor or smoke.
As a guideline, in a normal office environment (25°C) operating life is not
expected to be reached within the maintenance support period (5 years).
However, operating life may be reached more quickly if, for example, the product
is used in a hot environment. The customer shall bear the cost of replacing
replaceable components which have exceeded their operating life. Note that
these are only guidelines, and do not constitute a guarantee of trouble-free
operation during the maintenance support period.
High safety use
This product has been designed and manufactured for general uses such as
general office use, personal use, domestic use and normal industrial use. It has
not been designed or manufactured for uses which demand an extremely high
level of safety and carry a direct and serious risk to life or body if such safety
cannot be ensured.

Operating Manual ETERNUS JX40 S2
© cognitas. Gesellschft für Technik-Dokumentation mbH 2015 Pfad: C:\Users\gudat\Documents\______FTS\_STORAGE\JX40_S2\FM\sx40-ba-en\sx40-ba-en.vor
These uses include control of nuclear reactions in nuclear power plants,
automatic airplane flight control, air traffic control, traffic control in mass
transport systems, medical devices for life support, and missile guidance control
in weapons systems (hereafter, “high safety use”). Customers should not use
this product for high safety use unless measures are in place for ensuring the
level of safety demanded of such use. Please consult the sales staff of Fujitsu if
intending to use this product for high safety use.
Measures against momentary voltage drop
This product may be affected by a momentary voltage drop in the power supply
caused by lightning. To prevent a momentary voltage drop, use of an AC
uninterruptible power supply is recommended.
(This notice follows the guidelines of Voltage Dip Immunity of Personal
Computer issued by JEITA, the Japan Electronics and Information Technology
Industries Association.)
Technology controlled by the Foreign Exchange and Foreign Trade
Control Law of Japan
Documents produced by FUJITSU may contain technology controlled by the
Foreign Exchange and Foreign Trade Control Law of Japan. Documents which
contain such technology should not be exported from Japan or transferred to
non-residents of Japan without first obtaining authorization in accordance with
the above law.
Harmonic Current Standards
This product conforms to harmonic current standard JIS C 61000-3-2.
Only for the Japanese market:
Please refer to the following internet address for further information on the
usage and operation conditions of each available type of hard disk drive:
http://primeserver.fujitsu.com/primergy/harddisk/

ETERNUS JX40 S2 Operating Manual
Contents
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.1 Target Group . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.2 Structure of the Manual . . . . . . . . . . . . . . . . . . . . 10
1.3 Documentation Overview . . . . . . . . . . . . . . . . . . . 11
1.4 Notation Conventions . . . . . . . . . . . . . . . . . . . . . 12
1.5 Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . 12
2 Important Notes . . . . . . . . . . . . . . . . . . . . . . . . 15
2.1 Notes on Safety . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.2 Electrostatic-sensitive Component Label . . . . . . . . . . 17
2.3 CE Certificate . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.4 FCC Class A Compliance Statement . . . . . . . . . . . . . 18
2.5 Notes on Mounting the Rack . . . . . . . . . . . . . . . . . 19
2.6 Notes on Transportation . . . . . . . . . . . . . . . . . . . . 19
2.7 Environmental protection . . . . . . . . . . . . . . . . . . . 20
3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.1 Installation Steps . . . . . . . . . . . . . . . . . . . . . . . . 23
3.2 Unpacking the Storage Subsystem . . . . . . . . . . . . . . 24
3.3 Installing the ETERNUS JX40 S2 in the Rack . . . . . . . . . 25
3.3.1 Requirements of the Rack . . . . . . . . . . . . . . . . . . . . 25
3.3.2 Rack mounting . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.4 Switching the Storage Subsystem ON/OFF . . . . . . . . . 31

Operating Manual ETERNUS JX40 S2
Contents
© cognitas. Gesellschft für Technik-Dokumentation mbH 2015 Pfad: C:\Users\gudat\Documents\______FTS\_STORAGE\JX40_S2\FM\sx40-ba-en\sx40-ba-en.ivz
4 Operating and Indicator Elements . . . . . . . . . . . . . . . 33
4.1 Front Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
4.1.1 Operation Panel . . . . . . . . . . . . . . . . . . . . . . . . . . 34
4.1.2 Disk LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
4.2 Rear Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4.2.1 I/O Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
4.2.2 Power Supply Unit (PSU) . . . . . . . . . . . . . . . . . . . . . 39
5 Hard Disk Drives . . . . . . . . . . . . . . . . . . . . . . . . . 41
5.1 Handling Hard Disk Drives . . . . . . . . . . . . . . . . . . . 41
5.2 Removing/Installing Hard Disk Drive/Drive Dummy . . . . . . 42
6 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
6.1 SAS Connection . . . . . . . . . . . . . . . . . . . . . . . . . 47
6.2 Power Supply Connection . . . . . . . . . . . . . . . . . . . 49
7 Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . 51
7.1 Basic RAID controller / HBA configuration . . . . . . . . . . 51
7.2 RAID controller / HBA configuration and maximal storage
configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
7.3 RAID controller / HBA configuration with two way storage . . 53
7.3.1 Host Bus Adapter . . . . . . . . . . . . . . . . . . . . . . . . . 53
7.4 Redundant controller and storage two way configuration . . 54
7.5 Redundant controller and storage with file sharing . . . . . 55
8 Fault Clearing . . . . . . . . . . . . . . . . . . . . . . . . . . 57
8.1 Problem Solutions and Tips . . . . . . . . . . . . . . . . . . 58
8.1.1 Identification LED (Front) . . . . . . . . . . . . . . . . . . . . . 58
8.1.1.1 Identification status LED is on . . . . . . . . . . . . . . . . . 58

ETERNUS JX40 S2 Operating Manual
Contents
8.1.2 Fault LED (Front) . . . . . . . . . . . . . . . . . . . . . . . . 58
8.1.2.1 Fault LED is on during operation . . . . . . . . . . . . . . . 58
8.1.3 Power LED (Front) . . . . . . . . . . . . . . . . . . . . . . . . 58
8.1.3.1 Power LED remains dark . . . . . . . . . . . . . . . . . . . 58
8.1.4 I/O Module (IOM) . . . . . . . . . . . . . . . . . . . . . . . . 59
8.1.5 Temperature Sensor Error Message . . . . . . . . . . . . . . 59
8.1.6 Error LED of the Hard Disk Drive Indicates Disk Failure . . . . 59
8.1.7 The ETERNUS JX40 S2 does not Power on with the Attached
Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
9 Replacing Components . . . . . . . . . . . . . . . . . . . . 61
9.1 Power Supply Unit . . . . . . . . . . . . . . . . . . . . . . . 61
9.2 I/O Module . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
9.3 Operation Panel . . . . . . . . . . . . . . . . . . . . . . . . 64
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Related Publications . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Operating Manual ETERNUS JX40 S2
Contents
© cognitas. Gesellschft für Technik-Dokumentation mbH 2015 Pfad: C:\Users\gudat\Documents\______FTS\_STORAGE\JX40_S2\FM\sx40-ba-en\sx40-ba-en.ivz

ETERNUS JX40 S2 Operating Manual 9
1 Introduction
The functionality, mechanics and design of the ETERNUS®JX40 S2 storage
subsystem are optimally adapted to the servers of Fujitsu Technology Solutions.
It is designed to be used as rack model. In the 19-inch rack, the
ETERNUS JX40 S2 subsystem occupies two height units.
The ETERNUS JX40 S2 storage subsystem can accommodate drives and
SSDs as follows:
A maximum of four ETERNUS JX40 S2 storage subsystems can be daisy-
chained in a connection to one RAID controller/HBA port.
Server Management/ServerView
(Only for connection to PRIMERGY servers and ServerView Suite package)
ServerView and the related agents are set up within the group of servers and
storage subsystems being monitored. The received informations are evaluated
by ServerView and processed for display or forwarding to the administrator
(manager).
IWhen installing ETERNUS JX40 S2 storage subsystem in connection
with ServerView please install the ServerView Suite V10.10.04 or higher
on each of the connected servers (will be implemented later).
Notes to installing and update see at the documentation of ServerView (see
also "Related Publications" on page 79).
2.5" Up to 24 drives including up to 4 SSDs
3.5" Up to 12 drives

10 Operating Manual ETERNUS JX40 S2
Target Group Introduction
© cognitas. Gesellschft für Technik-Dokumentation mbH 2015 Pfad: C:\Users\gudat\Documents\______FTS\_STORAGE\JX40_S2\FM\sx40-ba-en\sx40-ba-en.k01
1.1 Target Group
The operating instructions are intended for the person responsible for installing
the hardware and correctly operating the system. The operating instructions
contain all the descriptions which are of importance for commissioning your
ETERNUS JX40 S2 storage subsystem in so far as they do not form part of the
publication of your server system.
To understand the different expansion options it is necessary to have a
knowledge of hardware and data transmission, as well as basic knowledge of
the operating system used.
1.2 Structure of the Manual
The ETERNUS JX40 S2 storage subsystem manual describes how to install
and configure the subsystem and perform expansions or upgrades.
You will find further information in the documentation of your PRIMERGY server.
This manual consists of the following chapters:
●Important Notes
This chapter contains instructions on the safe operation of your storage
subsystem as well as information about environmental protection.
●Operating and Indicator Elements
This chapter gives a detailed description of the operating panel and the
connecting elements on the rear panel of the corresponding storage
subsystem.
●Hard Disk Drives
This chapter describes in detail how the hot-plug hard disk drives must be
dealt with.
●Connections
This chapter describes the SAS and the mains connection.
The possibilities of supplying the storage subsystem with mains voltage are
also described.
●Configurations
This part of the manual gives configuration examples.

ETERNUS JX40 S2 Operating Manual 11
Introduction Documentation Overview
●Installation
The activities needed to install and commission the storage subsystem are
described.
●Fault Clearing
This chapter contains advice on solving problems that occur on
commissioning or during the operation of the storage subsystem.
●Replacing Components
This part of the manual describes the fitting and removing of power supply
units and I/O modules.
1.3 Documentation Overview
More information on the subsystem can be found in the following documents:
●“SETUP ETERNUS JX40 S2 SAS 2.5" / 3.5" HDD” leaflet
“はじめにお読み く ださい ” for the Japanese market (only included as a
printed copy)
●“Safety notes and other important information” manual
“安全上のご注意 ” for the Japanese market
●“Warranty” manual
“ 保証書 ” for the Japanese market

12 Operating Manual ETERNUS JX40 S2
Notation Conventions Introduction
© cognitas. Gesellschft für Technik-Dokumentation mbH 2015 Pfad: C:\Users\gudat\Documents\______FTS\_STORAGE\JX40_S2\FM\sx40-ba-en\sx40-ba-en.k01
1.4 Notation Conventions
1.5 Technical Data
Italics identifies commands and entries in flow text
Semibold highlights text
“Quotation marks” indicates references to other chapters or manuals
Êidentifies an operation that you have to perform
Iindicates additional information, notes and tips
VCAUTION! indicates warnings, which, if ignored, will endanger your
health, the operability of your server or the security of
your data
Table 1: Notation conventions
Installation specification
19" rackmount 2 U (height units)
Dimension (W x D x H) 2.5": 482 x 540 x 88 mm
3.5": 482 x 560 x 88 mm
Weight 35 kg (depending on the number of disks
installed)
Service area Front: 850 mm or more
Rear: 850 mm or more
Power voltage AC 100 - 120 V/ AC 200 - 240 V
Power frequency 50 / 60 Hz
Maximum power consumption 2.5": 430 W (440 VA)
3.5": 340 W (350 VA)
Power supply efficiency 92 %
No. of PSUs / power phase 2 PSUs, full redundant /
phase redundancy possible

ETERNUS JX40 S2 Operating Manual 13
Introduction Technical Data
Environmental
Maximum heat generation 2.5": 1600 kJ/h (1517 btu/h)
3.5": 1300 kJ/h (1232 btu/h)
Temperature (operating) 10 to 40°C
Temperature (not operating) 0 to 50°C
Temperature gradient 15°C/Hr or less
Humidity (operating) 20 – 80 % relative humidity, non-condensing
Humidity (not operating) 8 – 80 % relative humidity, non-condensing
Humidity gradient 30 %/day or less
Altitude 3,000 m
Sound power
(LWAd; 1B = 10dB)
6.0 B
Sound pressure (LpAm) 43.5 db(A)
Noise notes measured according to ISO7779 and declared
according to ISO9296
Operating environment FTS 04230 - Guideline for Data Center
(installation specifications)
Operating environment link:
http://globalsp.ts.fujitsu.com/dmsp/Publications/public/FTS-04230-Specification-for-DataCenter.pdf
Compliance
Product safety UL 60950-1, CSA-C22.2 No. 60950-1, EN 60950-1, IEC
60950-1
Electromagnetic
compatibility
CNS 13438, FCC Part-15 Class A, ICES 003 Class A, EN
55022 Class A, VCCI Class A, AS/NZS CISPR 22 Class
A
CE certification 2004/108/EC, 2006/95/EC, 2011/65/EC
Approvals CB, CE, C-Tick, EAC, FCC, VCCI
Environmental
compliance
RoHS compliant, WEEE compliant

14 Operating Manual ETERNUS JX40 S2
Technical Data Introduction
© cognitas. Gesellschft für Technik-Dokumentation mbH 2015 Pfad: C:\Users\gudat\Documents\______FTS\_STORAGE\JX40_S2\FM\sx40-ba-en\sx40-ba-en.k01
For more details and possibly updated information refer to the
“ETERNUS JX40 S2 Data Sheet” available at www.Fujitsu.com/eternus.
Compliance notes There is general compliance with the safety requirements
of all European countries and North America. National
approvals required in order to satisfy statutory regulations
or for other reasons can be applied for on request.
Comliance link http://globalsp.ts.fujitsu.com/sites/certificates/default.aspx
Compliance

ETERNUS JX40 S2 Operating Manual 15
2 Important Notes
2.1 Notes on Safety
In this section you will find information that you must note when using the
storage subsystem.
This device complies with the relevant safety standards for IT equipment.
IThe following safety notes are also provided in the “Safety notes and
other important information” manual. Also pay attention to the notes in
the operating manual of the connected PRIMERGY system.
If you have any questions relating to setting up and operating your system in the
environment where you intend to use it, please contact your sales outlet or our
customer service team.
VCAUTION!
●The actions described in these instructions should only be performed
by technical specialists. Equipment repairs should only be performed
by service personnel. Any unauthorized openings and improper
repairs could expose the user to risks (electric shock, energy
hazards, fire hazards) and could also damage the equipment. Please
note that any unauthorized openings of the device will result in the
invalidation of the warranty and exclusion from all liability.
●Transport the device in its original packaging or in other suitable
packaging which will protect it against shock or impact.
●Read the notes on environmental conditions in section "Technical
Data" on page 12 before setting up and operating the device.
●If the device is brought in from a cold environment, condensation may
form both inside and on the outside of the machine.
Wait until the device has acclimatized to room temperature and is
absolutely dry before starting it up. Material damage may be caused
to the device if this requirement is not observed.
●Check that the rated voltage specified on the type label is the same
as the local line voltage.

16 Operating Manual ETERNUS JX40 S2
Notes on Safety Important Notes
© cognitas. Gesellschft für Technik-Dokumentation mbH 2015 Pfad: C:\Users\gudat\Documents\______FTS\_STORAGE\JX40_S2\FM\sx40-ba-en\sx40-ba-en.k02
VCAUTION!
●The device must only be connected to a properly grounded wall outlet
(the device is fitted with a tested and approved power cable).
●Make sure that the power sockets on the device and the protective
grounded outlet of the building’s wiring system is freely accessible.
●Switching off the device does not cut off the supply of power. To do
this you must remove the power plugs.
●Before opening the unit, switch off the device and then pull out the
power plugs.
●Route the cables in such a way that they do not form a potential
hazard (make sure no-one can trip over them) and that they cannot
be damaged. When connecting up a device, refer to the relevant
notes in this manual.
●Never connect or disconnect data transmission lines during a storm
(lightning hazard).
●Systems which comprise a number of cabinets must use a separate
fused socket for each cabinet.
●The servers and the directly connected external storage subsystems
should be connected to the same power supply distributor. Otherwise
you run the risk of losing data if, for example, the central processing
unit is still running but the storage subsystem has failed during a
power failure.
●Make sure that no objects (such as bracelets or paper clips) fall into
or liquids spill into the device (risk of electric shock or short circuit).
●In emergencies (e.g. damage to housings, power cords or controls or
ingress of liquids or foreign bodies), immediately power down the
device, pull out the power plugs and notify your service department.
●Note that proper operation of the system (in accordance with IEC
60950-1/DIN EN 60950-1) is guaranteed only if slot covers are
installed on all vacant slots and/or dummies on all vacant bays and
the housing cover is fitted (cooling, fire protection, RFI suppression).

ETERNUS JX40 S2 Operating Manual 17
Important Notes Electrostatic-sensitive Component Label
2.2 Electrostatic-sensitive Component Label
Electrostatic-sensitive components may be identified by the following sticker:
Figure 1: Electrostatic-sensitive component sticker
You must follow the instructions below when handling modules containing
electrostatic-sensitive components
ÊDischarge static electricity from your body (for example by touching a
grounded metal object) before handling modules containing electrostatic-
sensitive components.
ÊThe equipment and tools you use must be free of static charge.
ÊRemove the power plug before installing or removing modules containing
electrostatic-sensitive components.
ÊOnly hold modules containing electrostatic-sensitive components by their
edges.
ÊDo not touch any of the pins or track conductors on a module containing
electrostatic-sensitive components.
ÊUse a grounding strap designed for the purpose, to connect you to the
system unit as you install the modules.
ÊPlace all components on a static-safe base.
IAn exhaustive description of the handling of modules containing
electrostatic-sensitive components can be found in the relevant
European and international standards (DIN EN 61340-5-1, ANSI/ESD
S20.20).

18 Operating Manual ETERNUS JX40 S2
CE Certificate Important Notes
© cognitas. Gesellschft für Technik-Dokumentation mbH 2015 Pfad: C:\Users\gudat\Documents\______FTS\_STORAGE\JX40_S2\FM\sx40-ba-en\sx40-ba-en.k02
2.3 CE Certificate
2.4 FCC Class A Compliance Statement
If there is an FCC statement on the device, it applies to the products covered in
this manual, unless otherwise specified herein. The statement for other
products will appear in the accompanying documentation.
IThis equipment has been tested and found to comply with the limits for a
"Class A" digital device, pursuant to Part 15 of the FCC rules and meets
all requirements of the Canadian Interference-Causing Equipment
Standard ICES-003 for digital apparatus. These limits are designed to
provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in strict accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no warranty that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
●Reorient or relocate the receiving antenna.
●Increase the separation between equipment and the receiver.
●Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
●Consult the dealer or an experienced radio/TV technician for help.
Fujitsu is not responsible for any radio or television interference caused
by unauthorized modifications of this equipment or the substitution or
attachment of connecting cables and equipment other than those
specified by Fujitsu. The correction of interferences caused by such
unauthorized modification, substitution or attachment will be the
The system complies with the requirements of the EC directives
2004/108/EC regarding "Electromagnetic Compatibility" and
2006/95/EC "Low Voltage Directive" and the directive of the
European Parliament and Council 2011/65/EU. This is indicated by
the CE marking (CE = Communauté Européenne).

ETERNUS JX40 S2 Operating Manual 19
Important Notes Notes on Mounting the Rack
responsibility of the user. The use of shielded I/O cables is required when
connecting this equipment to any and all optional peripheral or host
devices. Failure to do so may violate FCC and ICES rules.
WWARNING
This is a class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.
2.5 Notes on Mounting the Rack
●For safety reasons, at least two people are required to install the rack-
mounted model because of its weight and size. (For the Japanese market,
please refer to manual “ 安全上のご注意 ”.)
●When connecting and disconnecting cables, observe the notes in the
operating manual of your PRIMERGY system and the comments in the
“Important notes” chapter in the technical manual supplied with the rack.
●Ensure that the anti-tilt bracket is correctly mounted when you set up the
rack.
●For safety reasons, no more than one unit may be withdrawn from the rack
at any one time during installation and maintenance work. There is a danger
that the rack will tilt forward.
●The power supply to the rack must be installed by an authorized specialist
(electrician).
2.6 Notes on Transportation
ITransport the storage subsystem in its original packaging or in other
suitable packaging which will protect it against shock or impact.
Do not unpack it until all transport maneuvers are completed.
If you need to lift or transport the storage subsystem, ask someone to
help you.

20 Operating Manual ETERNUS JX40 S2
Environmental protection Important Notes
© cognitas. Gesellschft für Technik-Dokumentation mbH 2015 Pfad: C:\Users\gudat\Documents\______FTS\_STORAGE\JX40_S2\FM\sx40-ba-en\sx40-ba-en.k02
2.7 Environmental protection
Environmentally-friendly product design and development
This product has been designed in accordance with the Fujitsu standard for
“environmentally friendly product design and development”. This means that
key factors such as durability, selection and labeling of materials, emissions,
packaging, ease of dismantling and recycling have been taken into account.
This saves resources and thus reduces the harm done to the environment.
Further information can be found at:
–http://ts.fujitsu.com/products/standard_servers/index.html (for the EMEA market)
–http://jp.fujitsu.com/platform/server/primergy/concept/ (for the Japanese
market)
Energy-saving information
Devices that do not need to be constantly switched on should be switched off
until they are needed as well as during long breaks and after completion of work.
Packaging information
This packaging information doesn’t apply to the Japanese market.
Do not throw away the packaging. You may need it later for transporting the
system. If possible, the equipment should only be transported in its original
packaging.
Information on handling consumables
Please dispose of printer consumables and batteries in accordance with the
applicable national regulations.
In accordance with EU directives, batteries must not be disposed of with
unsorted domestic waste. They can be returned free of charge to the
manufacturer, dealer or an authorized agent for recycling or disposal.
All batteries containing pollutants are marked with a symbol (a crossed-out
garbage can). They are also marked with the chemical symbol for the heavy
metal that causes them to be categorized as containing pollutants:
Cd Cadmium
Hg Mercury
Pb Lead