Furniture of America Audrey CM7729-Q User manual

1) Prepare 2 bolts assembly by
inserting lock washer (#B), then flat
washer (#C) onto bolts (#A). Align
HB legs (#4R/L) to the holes of the
HB support (#5). Secure by using
bolts (#A).
2) Attach threaded bolts (#D) to the holes of the headboard (#1).
Align HB legs (#4R/L) to the threaded bolts (#D). Secure by
using curved washer (#E), lock washer (#B) and hex nut (#F)
onto threaded bolts (#D).

Attach threaded bolts (#D) to the holes of the headboard legs (#4R/L) and
footboard (#2). Align side rails (#3) to the threaded bolts (#D). Secure by using
curved washer (#E), lock washer (#B) and hex nut (#F) onto threaded bolts (#D).
Attach support legs (#7) to the holes of the slats (#6).
Adjust the leveler of the support legs (#7) according
to ground level.

Align slats (#6) to the side rails (#3), then secure by using screws (#I).

Parts List
Hardware List
#1 x 1pc
#2 x 1pc
#D x 12pcs
#A x 2pcs
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Headboard
#3 x 2pcs
#6 x 4pcs
#7 x 8pcs Ø1/4"
#5 x 1pc
Page 3 of 6
#4 x 2pcs
Footboard
Side Rail
Threaded Pins Ø5/16" X 3" Headboard Leg (L&R)
Headboard Support
Slat
#E x 12pcs
Half Moon Ø5/16"
Bolt Ø5/16" X 1-3/4"
#B x 14pcs
#C x 2pcs
Spring Washer Ø5/16"
Flat Washer Ø5/16"
Allen Wrench M4
#F x 12pcs
Spring Washer Ø5/16"
#G x 1pc
Wrench 12mm
#H x 1pc
#I x 8pcs
Screw Ø9 x 1"
Support Leg 263 x 30 x 30mm

1) Prepare 2 bolts assembly by
inserting lock washer (#B), then flat
washer (#C) onto bolts (#A). Align
HB legs (#4R/L) to the holes of the
HB support (#5). Secure by using
bolts (#A).
2) Attach threaded bolts (#D) to the holes of the headboard (#1).
Align HB legs (#4R/L) to the threaded bolts (#D). Secure by
using curved washer (#E), lock washer (#B) and hex nut (#F)
onto threaded bolts (#D).

Attach threaded bolts (#D) to the holes of the headboard legs (#4R/L) and
footboard (#2). Align side rails (#3) to the threaded bolts (#D). Secure by
using curved washer (#E), lock washer (#B) and hex nut (#F) onto threaded
bolts (#D).
Attach support legs (#7) to the holes of the slats (#6).
Adjust the leveler of the support legs (#7) according
to ground level.

Align slats (#6) to the side rails (#3), then secure by
using screws (#I).

Parts List
Hardware List
#1 x 1pc
#2 x 1pc
#D x 12pcs
#A x 2pcs
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Headboard
#3 x 2pcs
#6 x 4pcs
#7 x 8pcs Ø1/4"
#5 x 1pc
Page 3 of 6
#4 x 2pcs
Footboard
Side Rail
Threaded Pins Ø5/16" X 3"
Headboard Leg (L&R)
Headboard Support
Slat
#E x 12pcs
Half Moon Ø5/16"
Bolt Ø5/16" X 1-3/4"
#B x 14pcs
#C x 2pcs
Spring Washer Ø5/16"
Flat Washer Ø5/16"
Allen Wrench M4
#F x 12pcs
Hex Nut Ø5/16"
#G x 1pc
Wrench 12mm
#H x 1pc
#I x 8pcs
Screw Ø9 x 1"
Support Leg 263 x 30 x 30mm

2) Attach threaded bolts (#D) to the holes of the headboard (#1). Align HB legs
(#4R/L) to the threaded bolts (#D). Secure by using curved washer (#E), lock
washer (#B) and hex nut (#F) onto threaded bolts (#D).
1) Prepare 2 bolts assembly by
inserting lock washer (#B), then
flat washer (#C) onto bolts
(#A). Align HB legs (#4R/L) to
the holes of the HB support
(#5). Secure by using bolts
(#A).

Attach threaded bolts (#D) to the holes of the headboard legs (#4R/L) and
footboard (#2). Align side rails (#3) to the threaded bolts (#D). Secure by
using curved washer (#E), lock washer (#B) and hex nut (#F) onto
threaded bolts (#D).
Attach support legs (#7) to the holes of the slats (#6).
Adjust the leveler of the support legs (#7) according
to ground level.

Align slats (#6) to the side rails (#3), then
secure by using screws (#I).