Furniture of America CM-DK6846 User manual

Assembly Instructions
EASY DIFFICULT
Page 1 of 8
ASSEMBLY RATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
CM-DK6846
2 PERSONS RECOMMENDED
Tools Required For Assembly:
Allen Wrench
(Included)
Phillips Screwdriver
(Not Included)
Rev: 16-09-16

Page 2 of 8
BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjusetment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.

Parts List
Hardware List
#1 x 1pc
#2 x 4pcs
#A x 16pcs
#B x 16pcs
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Cabinet body
#3 x 2pcs #C x 16pcs
Page 3 of 8
Leg
Hutch Top
Bolt 1/4 x 2"
Flat Washer Ø1/4"
Lock Washer Ø1/4"
#4 x 4pcs
#5 x 1pc
Hutch panel
Hutch Back
#E x 4pcs
#F x 4pcs
Allen Key 4mm
#D x 1pc
Barrel Nuts Ø1/4"
Bolt 1/4" x 1-3/8"
#6 x 2pcs
#7 x 2pcs
Drawer
Mirror Support
#8 x 1pc
Mirror Middle
#9 x 2pcs
Mirror L&R

Page 4 of 8
#A x 8pcs
#B x 8pcs
#C x 8pcs
#A x 2pcs
#E x 2pcs
#1 #2
#A
#C
#B
#D
#3
#5 #4
#4
#4
#4
#E
#E
#D
#D
#A
#A
1. Prepare 8 bolt assemblies
by first inserting a lock
washer (#C) onto the bolt
(#A) then a flat washer (#B)
onto that same bolt (#A).
2. Align the legs (#2) to the corners along the cabinet body
(#1), then insert the bolt assemblies from within and secure.
Remove drawers
to assemble legs.
1. Insert the hutch panels (#4)
into the holes displayed.
2. Insert the barrel
nuts (#E) into the
large holes. Make
sure the openings
face the holes.
3. Align the hutch top (#3), then insert
the bolts (#A) into the holes and
secure using the Allen wrench (#D).

Page 5 of 8
#A x 2pcs
#E x 2pcs
#5
#1
#A
#D
#5
#1
#E
Insert into the
holes along the
cabinet body (#1).
Insert the barrel nuts (#E) into
the large holes with the openings
facing the hole, then insert the
bolts (#A) from beneath. Secure
using the Allen wrench (#D).

#F
#C
#B
#D
Page 6 of 8
#B x 4pcs
#C x 4pcs
#F x 4pcs
#A
#C
#B
#D
#1
#A x 4pcs
#B x 4pcs
#C x 4pcs
#8
#7
1. Align the mirror supports (#7)
to the holes along the back.
2. Prepare 4 bolt assemblies by first
inserting a lock washer (#C) onto the
bolt (#A) then a flat washer (#B) onto
that same bolt (#A). Insert a bolt
assembly into each hole and secure.
1. Align the mirror (#8) to the
holes along the supports.
2. Prepare 4 bolt assemblies by first
inserting a lock washer (#C) onto the
bolt (#F) then a flat washer (#B) onto
that same bolt (#F). Insert a bolt
assembly into each hole and secure.

Page 7 of 8
#6
ASSEMBLY IS COMPLETED
#9
#8
#9
#8
#9
Insert the brackets
along the left and right
mirrors (#9) into the
pins along mirror (#8).

#A
#C
#D
#B
Parts List
Hardware List
#1 x 1pc
#2 x 4pcs
#A x 8pcs
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Seat
#B x 8pcs
Page 8 of 8
Leg
Bolt Ø1/4" x 2"
#C x 8pcs
/RFN Washer Ø1/4"
#D x 1pc
Allen Key 4mm
#A x 8pcs
#B x 8pcs
#C x 8pcs
Flat Washer Ø1/4"
#2
#1