Furniture of America CM4220-3PK User manual

EASY
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
Allen Wrench (Included)
Assembly Instructions
Tools Required for Assembly:
Rev.14-10-17
Page 1 of 9
DIFFICULT
ASSEMBLY RATING
CM4220-3PK
2 PERSONS RECOMMENDED

Page 2 of 9

Parts List Hardware List
#1 x 2 pcs
C/T Leg Stand
#2 x 1 pc
C/T Stand Support
#3 x 1 pc
Coffee Table Frame
#A x 18 pcs
Bolt 1/4”x5/8”
#B x 12 pcs
Bolt 1/4”x1-1/8”
Before you begin, please read Page 2
of “Assembly and Care Advice”.
And remember, do not tighten until
each step is completed or instructed.
#C x 14 pcs
Spacer
MD
#D x 1 pc
Allen Wrench
#4 x 1 pc
C/T Glass Top
Page 3 of 9
#5 x 4 pcs
E/T Leg Stand
#6 x 2 pcs
E/T Stand Support
#7 x 2 pcs
End Table Frame
#8 x 2 pcs
E/T Glass Top
Due to the size and/or weight of this
product, it is highly recommended
that the assembly should be done
near the area of its intended location.
Make sure you have enough space
to move around during the assembly.
ALWAYS have at least two people to
help with transporting and
assembling the product to avoid any
potential injury and/or damage.

Turn right (clockwise) to tighten
Page 4 of 9
#A x 4 pcs
I. Insert the coffee table
stand support (#2) onto
the 2 coffee table leg
stands (#1).
II. Insert 4 bolts (#A)
through the brackets of
the coffee table stand
support (#2) and secure
those bolts (#A) using the
Allen wrench (#D) to lock
them with the 2 coffee
table leg stands (#1).
#A x 2 pcs
Insert 2 bolts (#A) through the pre-drilled
holes of the coffee table stand support
(#2) and secure those bolts (#A) using the
Allen wrench (#D) to lock them with the 2
coffee table leg stands (#1).
#1
#1
#2
Turn right (clockwise) to tighten

Page 5 of 9
I. Align the assembled
coffee table leg stands
(#1) with the pre-drilled
holes on the coffee table
frame (#3).
II. Insert 4 bolts (#B) through
the coffee table leg stands
(#1) and secure those
bolts (#B) using the Allen
wrench (#D) to lock them
with the coffee table frame
(#3).
#1
#1
#3
#B x 4 pcs
#C x 6 pcs
Carefully place the coffee table in the upright position.
Place 6 spacers (#C) on top of the coffee table frame
(#3) as shown on diagram below.
Turn right (clockwise) to tighten

Page 6 of 9
With the help of another person, carefully place the coffee
table glass top (#4) over the spacers (#D) and the table
frame (#3).
#3
#D
Make sure the coffee table is rested on a flat surface and does not
feel loose or wobbly. If it does, double check that the bolts/screws
are secured and properly tightened.

Page 7 of 9
Turn right (clockwise) to tighten
I. Insert the end table
stand support (#6)
onto the 2 end table
leg stands (#5).
II. Insert 4 bolts (#A)
through the brackets
of the end table stand
support (#6) and
secure those bolts
(#A) using the Allen
wrench (#D) to lock
them with the 2 end
table leg stands (#5).
#A x 8 pcs
X 2
Insert 2 bolts (#A) through the pre-drilled
holes of the end table stand support (#6) and
secure those bolts (#A) using the Allen
wrench (#D) to lock them with the 2 end table
leg stands (#5).
#A x 4 pcs
#6
#5 #5
Turn right (clockwise) to tighten
X 2

Page 8 of 9
Turn right (clockwise) to tighten
X 2
X 2
I. Align the assembled end table
leg stands (#5) with the pre-
drilled holes on the end table
frame (#7).
II. Insert 4 bolts (#B) through the
end table leg stands (#5) and
secure those bolts (#B) using
the Allen wrench (#D) to lock
them with the end table frame
(#7).
#5 #5
Carefully place the end table in the upright position.
Place 4 spacers (#C) on top of the end table frame (#7)
as shown on diagram below.
#B x 8 pcs
#C x 8 pcs
#7
Turn right (clockwise) to tighten

Page 9 of 9
ASSEMBLY IS COMPLETED
Carefully place the end table glass top (#8) over the
spacers (#D) and the table frame (#7).
#8 X 2
Make sure the end tables are rested on a flat surface and do
not feel loose or wobbly. If they do, double check that the
bolts/screws are secured and properly tightened.
#7
#D