Furniture Solutions DERBY 1.8m User manual

INSTRUCTION MANUAL
DERBY 1.8m SHORT DINING TABLE
DERBY 2.1m LONG DINING TABLE
ITEM CODE: 18DER
118DER
Imported by Furniture Solutions (Aust) Pty Ltd New South Wales, Australia.
For any assistance with assembly or for missing parts please contact:
Place of purchase or Furniture Solutions on below
Customer Service (Australia) Phone-1300 794 188
Email- [e-mail]

PRE-ASSEMBLY PREPARATION
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage
the product
2. Take care when lifting. Product should be assembled as near as possible to the point of
use
3. Ensure that you have all required contents for complete assembly
4. Always read the assembly instructions carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over tighten the screws and bolts as this may damage the threads
218DER
20
MINUTES
ALLOW TIME PEOPLE REQUIRED
X2

PARTS LIST
318DER
Description Code
A
Table Top x 1
P.18005.TT
B
Brace x 1
P.18005.B
C
X Leg x 2
P.18005.XL
Derby 1.8m Short Table
Description Code
A
Table Top x 1
P.13060.TT
B
Brace x 1
P.13060.B
C
X Leg x 2
P.13060.XL
Derby 2.1m Long Table
D
Adjusting feet
X 4
E
Bolt & Washer
M6x20mm
X 16
F
Tool
X 1

418DER
ASSEMBLY INSTRUCTIONS
Please prepare work area as instructed in page 2:
To Attach X Leg:
Identify required hardware before you start assembly. Note do not over tighten any bolts,
tighten only until feels firm.
With the help of another person, lay table top [A] facing down as per diagram.
Next locate the threaded holes in metal tube attached to table top, you will find 4 sets of two
treaded holes.
Next with the help of a second person , take X Leg [C] place onto metal tube as shown in
diagram, aline hole in X leg with threaded holes in metal tube.
Warning please ensure you have threaded holes in middle of X Leg facing inwards.
While second person holds that in position, take bolt and washer together and insert thru holes,
to ensure thread has gripped correctly turn 2-3 times by hand. Do not tighten yet. Repeat for
the other 3 holes. Do not Tighten yet. Repeat for second X Leg. Do not tighten yet.
Move to next page…

518DER
ASSEMBLY INSTRUCTIONS
To Fit Brace,
You will need the help of another person thru this stage.
With the help of a second person to hold brace [B].
Take brace and hold horizontal as per diagram. Aline holes at end of brace with threaded holes
in X Leg.
Next take bolt and washer [E] together and insert thru hole into threaded hole on X leg,
ensure to seat thread correctly by hand turn 2-3 times until bolt has a grip in thread. Do not
Tighten as yet. Go to opposite end and fit bolt and washer as above. Now repeat for balance
of bolts.
Once all bolt fitted proceed to tighten all bolts by using tool [F] provided, start with table top
and work your way around and then up to brace, ensure you only tighten until bolt feels firm.
Over tightening may cause damage to threads. Do not Stand up yet. Move to Next page

618DER
ASSEMBLY INSTRUCTIONS
Assembly : Fit Height Adjuster feet
Please locate threaded hole at base of X Leg. Take adjusting feet [D] insert into threaded hole
and turn by hand until it stops. Repeat for all legs. Assembly Complete move to next section.
HOW TO SAFELY STAND TABLE ON LEGS
Please note this product is very heavy and needs to be lifted correctly as to not damage sub
frame and or legs.
With the help of a second or more person, lift product straight up in the air keeping it
horizontal, once you are comfortable and standing up straight then in unison rotate table top
until it is horizontal with legs pointing to the ground, Then lower gently to ground. Note if you
need to reposition product NEVER drag always lift to move.

718DER
This table is fitted with height adjusts on each leg, so you correct for small variations in level
on floor surface.
Simply raise the leg and adjust the feet to suit. Note much easier with a second person.
Clockwise to reduce the height of the leg.
Anticlockwise to lower the height of the leg
FEATURE OF TABLE IS THE ADJUSTABLE FEET

818DER
CARE AND MAINTENANCE
Varieties of materials are used in construction of “Outdoor” furniture range.
All will require some form of maintenance to extend the life of finishes and general appearance.
Please see below instruction unique to your chosen product.
Derby Bench Seat;
Table Top construction: Cement, black sand, fiberglass and paper fiber. With stone look surface,
spray Clear painted finish.
Base : Aluminium tube 1.4mm gauge; powder coated finish
Bench Top Finish;
The feature of a stone finish does have its’ draw backs, the uneven surface will catch dust and
grime and if not cleaned properly can build up and depending what chemicals are in the grime
can affect the paint finish.
Other factors like pollution, sea salt, vegetation, excessive heat and excessive moisture, will also
affect the paint finish.
Please follow below for regular cleaning.
Dusting regular use a soft clean dust pan brush to remove dust & grit.
Next warm water and with a soft cloth to remove the grim.
Remember to pat dry with a soft clean cloth.
Finding surface scratched please touch up with appropriate coloured paint.
Please clean up spills immediately. Ensure to dry properly before use.
Powder Coated Aluminium;
Powder coating is simular to a painted finish, the metal is coated with a paint powder then is
past thru a kiln to bond and harden paint onto metal.
Please follow below for regular cleaning
Bucket of warm water with a soft clean cloth or sponge, clean metal in one direction, do not rub
excessively. Ensure to pat dry as water drop will leave a mark on paint finish.
Definition of Regular Cleaning;
Numerus factors can influence the time frame for cleaning, depending area you live in, the
weather, positioning of the product (fully protected, partial protection, fully exposed to the
elements). You will need to monitor yourself to establish the cleaning requirement for situation.
Areas with high salt content and or pollution will require the most frequent cleaning.
To reduce some maintenance you should buy and use an outdoor cover to protect your
furniture from the elements when not in use.

918DER
SAFETY WARNINGS AND ADVICE
Notices and Advice
Please be advised that products are limited in design for residential use only and are not
suitable for commercial use.
Please be advised that materials used in your furniture are not impervious to neglect, acts of
god, abuse, alcohol spills, improper use of chemicals such as bleach or any solvent based
products.
Please be advised that heat sources such as barbeques, open fires,
temporary/mobile/overhead heaters, poorly insulated candle holders, hot pots, pans, hot
serving dishes can have adverse affects on your furniture.
Please be advised to use properly insulted placemats and coasters when serving hot or cold
dishes and drinks.
Please be advised that fitting, bolts, nuts and or screws should be checked periodically to
ensure they have not loosened over time. Remember do not overtighten.
Please be advised coverings and paint finishers are not animal proof. Claws can scratch
covering & saliva is acidic and can damage finish.
DO NOT
•Place in close proximity to open flame or heaters.
•Leave spills or food, clean off immediately
•Pull loose thread, cut them instead.
•Sit or lean on arms
•Stand on chair or bench's
•Stand on table tops
•Place heavy objects on table tops
•Place objects such as pot plants as a display piece on tables recommend weight
restriction for table top is 60kg across the table
Safety warnings
•DO NOT:
•drop, drag always move furniture with the help of another person lift and place only
•Over load bench seats recommended weight evenly distributed is 360kg IE: 3 people
120kg each; 4 people 90kg each.
•Tables, chairs & bench's are designed for seating, not work bench's.
•Allow child to play under table

10 18DER
WARRANTY DETAIL
1 Year Warranty
A one (1) year warranty applies to product against any defect associated with faulty
workmanship for a period of (1) year from date of purchase.
Furniture Solutions accepts no responsibility for defects caused by incorrect assembly,
mishandling, acts of god, general wear & tear, stains from spills/vegetation, chipping /
scratching, and exposure to extreme heat/cold, mould/mildew, hardware corrosion,
misuse of the products & defects caused by failure in duty of care for the product in
accordance with the care instructions.
Warranty only extends to original purchaser and is not transferable, except when given as a gift.
Goods are limited in design for domestic use only, and are not suitable for commercial use.
Please be aware place product in close proximity of heat sources, such as barbeque and heaters
will affect the finishes on goods and may void your warranty,
Duty of care:
While every attempt is made to supply product using quality components there is always
a need from consumer to help ensure a long life of use for product.
Proper use of item, only what it is designed to do. Designed for dining, not suitable for use as a
workbench, substitute ladder or dance floor.
Regular maintenance and cleaning
Please consult your Instruction manual included in packaging for advice of cleaning.
To extend the life of your outdoor furniture we recommend the following
Furniture covers should be used on furniture which is used in areas not protected from
elements.
Caution should be used when using oils, lotions & other chemicals such as chlorine.
Claim management:
To make a warranty claim, customers can either contact the retailer where the purchase
was made or Furniture Solutions on contact details on page 2. Proof of purchase will be
required before proceeding with any claim. In the case of product defects providing
photos may be able to speed up processing of the claim. If missing parts please refer to
assembly instructions for identification of said part and contact either of the above.
“Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure and for
compensation for any other reasonably foreseeable loss or damage. You are also entitled
to have the goods repaired or replaced if the goods fail to be of acceptable quality and
the failure does not amount to a major failure”.