Furniture Solutions OSBY 3Pc User manual

1
INSTRUCTION MANUAL
PRODUCT: OSBY 3Pc SETTING
ITEM CODE: 18OSBBS3W
MADE IN CHINA

PRE-ASSEMBLY PREPARATION
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage
the product
2. Take care when lifting. Product should be assembled as near as possible to the point of
use
3. Ensure that you have all required contents for complete assembly
4. Always read the assembly instructions carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over tighten the screws and bolts as this may damage the threads
2
30
MINUTES
ALLOW TIME PEOPLE REQUIRED
X2
For any assistance with assembly or missing parts please contact:
Place of purchase or Furniture Solutions on below
Customer Service (Australia) Phone–1300794 188
Email–[e-mail]

3
PARTS LIST
Side Table
Code Description QTY
J
FAJ19307
-S.LT
Side Table Leg with thread
1
K
FAJ19307
-S.LH
Side Table Leg with hole
1
L
FAJ19307
-S.B
Side
Table Rim 1
M
FAJ19307
-S.GP
Glass
Panel 1
E
FAJ19307HW
Flat Washer
1
S
FAJ19307HW
Spring Washer
5
F
FAJ19307HW
Short
Bolt 4
G
FAJ19307HW
Long
Bolt 1
H
FAJ19307HW
Cover Cap
5
I
FAJ19307HW
Tool
1

4
PARTS LIST
Chair
Code Description QTY
N
FAJ19307
-C.LT
Chair Leg with thread
2
O
FAJ19307
-C.LH
Chair Leg with hole
2
P
FAJ19307
-C.B
Chair seat
& back rest 2
Q
FAJ19307
-C.BC
Chair
back Cushion 2
R
FAJ19307
-C.SC
Chair
seat Cushion 2
E
FAJ19307HW
Flat
washer 10
F
FAJ19307HW
Short
Bolt 8
G
FAJ19307HW
Long
Bolt 2
H
FAJ19307HW
Cover
Cap 10
I
FAJ19307HW
Tool
1

5
ASSEMBLY INSTRUCTIONS
Foreword: Please read before you begin assembly
(warning do not use power or battery drills)
Upon opening carton you will need to organise your parts into like pieces IE: Side Table & Chair
parts. This will assist in quicker assembly. The most difficult parts to separate will be the legs.
Please follow below when sorting out parts.
The widest legs are for the chair you will 4 of them.
The tallest of the legs will be the Side Table 2 of them.
So start with the legs and go page by page to sort out bolts washer and a like. Now there are two
different legs one with a thread hole and one without. Note always fit threaded hole leg first.
Note it is important that you do not fully tighten bolts until instructed.

6
ASSEMBLY INSTRUCTIONS
ASSEMBLY-SIDE TABLE
Please follow pre-assembly instruction on page.2.
Step 1:
As indicated by diagram below place side table rim [L] upside down, locate the threaded holes in
base. Then Take leg [J] aline holes in base of leg with threaded holes in base as indicated in
diagram angled across base, while a second person holds leg in place, take short bolt [F] together
with spring washer [S] insert into holes, and by hand seat the thread correctly by turning 2-3
times, test if thread has gripped, lightly pull back on bolt. Do not tighten yet. Repeat for the
second bolt hole in leg. Move to Step2:

7
ASSEMBLY INSTRUCTIONS
ASSEMBLY-SIDE TABLE
Please follow pre-assembly instruction on page.2.
Step 2:
Next position second leg [K] over the top and across as indicated in diagram. At intersection of
legs fit long bolt [G] with spring washer [S] and also flat washer [E] insert thru hole and into
threaded hole, seat thread correctly by hand, turn 2-3 times, ensure thread has gripped. Do not
tighten yet. Fit small bolts with spring washer to second leg as previously. Make a check that all
appear to be fitted correctly.
Now proceed to tighten, please start with the long bolt at intersection of legs. Take tool [I] and
tighten until feels firm. Do not overtighten as this may cause damage to threads.
Next tighten all small bolts, and again do not overtighten. Once all bolts are tighten fit cover cap
using your thumb to push over bolt top.
Assembly complete now turn over frame and add Glass Panel [M]

8
ASSEMBLY INSTRUCTIONS
ASSEMBLY-CHAIR
Please follow pre-assembly instruction on page.2.
Step 1:
As indicated by diagram below place chair frame [P] upside down, locate the threaded holes in
base. Then Take leg [N] aline holes in base of leg with threaded holes in base as indicated in
diagram angled across base, while a second person holds leg in place, take short bolt [F] together
with flat washer [E] insert into holes, and by hand seat the thread correctly by turning 2-3 times,
test if thread has gripped, lightly pull back on bolt. Do not tighten yet. Repeat for the second bolt
hole in leg. Move to Step2:

9
ASSEMBLY INSTRUCTIONS
ASSEMBLY-CHAIR
Please follow pre-assembly instruction on page.2.
Step 2:
Next position second leg [O] over the top and across as indicated in diagram. At intersection of
legs fit long bolt [G] with flat washer [E] insert thru hole and into threaded hole, seat thread
correctly by hand, turn 2-3 times, ensure thread has gripped. Do not tighten yet. Fit small bolts
with flat washer to second leg as previously. Make a check that all appear to be fitted correctly.
Now proceed to tighten, please start with the long bolt at intersection of legs. Take tool [I] and
tighten until feels firm. Do not overtighten as this may cause damage to threads.
Next tighten all small bolts, and again do not overtighten. Once all bolts are tighten fit cover cap
using your thumb to push over bolt top.
Assembly complete now turn over frame and add Cushions [Q] & [R]

10
CARE & MAINTENANCE
Varieties of materials are used in construction of “Outdoor” furniture range.
All will require some form of maintenance to extend the life of finishes and general appearance.
Please see below instruction unique to your chosen product.
Osby Construction;
Aluminium Frame:
Tempered Glass:
Textilene Rope:
Polyester Fabric:
Powder Coated Aluminium;
Powder coating is simular to a painted finish, the metal is coated with a paint powder then is past
thru a kiln to bond and harden paint onto metal.
Please follow below for regular cleaning
Bucket of warm water with a soft clean cloth or sponge, clean metal in one direction, do not rub
excessively. Ensure to pat dry as water drop will leave a mark on paint finish.
Glass used is tempered for your safety; best results are to use table cloths, placemats & coasters
to avoid scratching surface. Keep dust free, clean underside of glass with a soft clean cloth. Use of
normal glass cleaning product is permissible but please rinse surrounding areas with clean water
to avoid damage to paint on aluminium frame
Textilene Sling Information;
The Textilene sling is a synthetic material made from a mixture of fibres of polyester thread
covered with a sheath of PVC, able to withstand compressive stresses, strains, atmospheric
agents and UV rays. For Outside use properties of material have a proven track record, while still
subject to fading strength will remain even after colour starts to fade. Shelf life again depends on
location & environment, regular cleaning & storage for best results for longevity.
Please follow below for regular cleaning
Use a bucket filled with warm water & a soft soap, sponge over frame till clean, once clean rinse
off with a hose, pat dry with a soft clean cloth before use. Every 4-6 weeks. Ensure not to be left
wet for long periods of time so as to avoid mould build up.