Furniture Solutions KIRRA 14KIR482 User manual

ASSEMBLY INSTRUCTION
KIRRA
ITEM CODE :14KIR482
Imported by Furniture Solutions (Aust) Pty Ltd
10-16 Daisy St, Revesby NSW, 2212, Australia
www.furnituresolutions.com.au
Please retain as has important information for future use
= Furniture Solutions =
H:102.5~73cm
:
c
95
1
D88~m
P1ITEM CODE :14KIR482
W:81.5cm

P2
PRE-ASSEMBLY PREPARATION
Before you start
Choose a clean, level, spacious assembly area . Avoid hard surfaces that
may damage the product
Take care when lifting . Product should be assembled as near as possible to
the point of use
Ensure that you have all required contents for complete assembly
Always read the assembly instructions carefully before beginning
assembly .
Keep all hardware parts and packaging out of reach of small children .
Do not over tighten the screws and bolts
as this may damage the threads
20
2
2
For any assistance for missing parts please refer to parts list on next page for identification.
Contact point of purchase or Furniture Solutions (Aust) Pty Ltd with below details
Email:
Free-call Australia PH: 1300 794 188
Website: www.furnituresolutions.com.au
Note:
Please when contacting Furniture Solutions have purchase details and model name on hand
cust[email protected]om.au
ITEM CODE :14KIR482

P3
1.Chair Base With Build-In Footrest 2.Backrest Cushion 3.Armrest Pads
3
1
2
3
ITEM CODE :14KIR482
M8X35
A
B
C
D
E
F
2PCS
1PC
1SET
4mm/6mm
M8X70 M6X16
M6X20
4PCS
2PCS
2PCS Lever

P4ITEM CODE :14KIR482
2
1
A
A
4
5
1
2
3
3
To Assemble Chair, attach backrest (2)
Take Chair base with cushion (1) place in upright position as shown in diagram, with the help of second person. Bring
backrest (2) to chair base (1). Locate at base of backrest & back of seat black metal tubes that have holes, you may
have to peel back leather covering to locate. Second person required to hold back rest level so bolts (A) can be
inserted and seated into tread provided, and then by hand seat both bolts (A) to ensure not to cross thread. Once
both seated correctly tighten with tool (F) tighten till you feel resistance, do not over tighten. Now attach upper
section of back rest to back of black bracket as shown in diagram, again second person required to keep backrest
square while fitting bolts (B). By hand start bolt (B) thru hole in bracket into backrest (2) again you may have to peel
back leather covering to locate threaded hole. Once both seated correctly take tool (F) and tighten bolts. Note these
bolts (B) are used as a pivot point for backrest movement and does not need to be tighten flat against metal.
To attach Armrest: Place armrest (3) as indicated in diagram, line up holes in armrest (3) with holes on bracket. Using
bolt (C) insert bolt thru hole in bracket and into armrest (3) then by hand seat bolt properly 2-3 turn, do not tighten
till both bolts fitted by hand. Once both seated use tool (F) to tighten. Repeat for other side.

P5ITEM CODE :14KIR482
1
2
3
To attach Lever: Ensure footrest is in rest position under chair, take lever (E) with knob pointing to rear of chair line
up the 2 red arrows slot lever (E) into position indicated on diagram, move around till holes line up, then by hand
insert bolt (D) turn 2-3 times to ensure thread seated properly, once seated tighten bolt till firm. Then gently push
lever forward till footrest is fully extended, this will expose a second hole, please repeat fitting as above. Assembly
complete

ASSEMBLY IS COMPLETE
P6ITEM CODE :14KIR482

P7ITEM CODE :14KIR482

P8ITEM CODE :14KIR482

P9ITEM CODE :14KIR482

P10 ITEM CODE :14KIR482