Furniture Solutions 17TOUHE User manual

Imported by Furniture Solutions (Aust) Pty Ltd New South Wales, Australia.
For any assistance with assembly or for missing parts please contact:
Place of purchase or Furniture Solutions on below
Customer Service (Australia) Phone-1300 794 188
Email- [e-mail]
INSTRUCTION MANUAL
TOULON RECLINER CHAIR
ITEM CODE: 17TOUHE
117TOUHE
=Furniture Solutions =

PRE-ASSEMBLY PREPARATION
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage
the product
2. Take care when lifting. Product should be assembled as near as possible to the point of
use
3. Ensure that you have all required contents for complete assembly
4. Always read the assembly instructions carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over tighten the screws and bolts as this may damage the threads
217TOUHE
30
MINUTES
ALLOW TIME PEOPLE REQUIRED
X2

PARTS LIST
317TOUHE

417TOUHE
ASSEMBLY INSTRUCTIONS
Please prepare work area as instructed in page 2:
To attach armrest:
Please arrange chair base with cushion [1] as displayed in diagram below. Locate threaded holes
inside the extended arm support. Take angled plate [A] and aline holes in angled plate with
threaded holes as indicated above. Note wording on angled plate please face wording towards
seat. Take bolt [B] and by hand insert thru hole into thread and turn 2-3 times to seat thread
correctly, repeat for other bolt. Once both seated correctly take tool provided [D] and tighten
both bolts. Repeat for other arm support section. Then take armrest pad [3], take note of the
diagram for correct direction place armrest pad. Next aline holes in angled plate with threaded
holes under armrest pad. Then by hand insert bolt [C] turn 2-3 times to seat thread correctly, do
not tighten yet. Repeat for other bolt. Once both bolt are seated correctly, take tool [D] and
tighten. Repeat for other armrest pad. Move to next page

517TOUHE
ASSEMBLY INSTRUCTIONS
To attach backrest [2]
Please review diagram below and locate the black tube fittings shown, note the tube section
in the chair base with cushion has a screw pre-fitted, please locate this before you start
assembly.
With the help of a second person in unison aline & slide the tube in backrest [2] into tube in
chair base with seat. Note both need to inserted at the same time, you may need to push up
material to get a clear view. Once insert ensure both sides are level and backrest has been
pushed down into tube. Once your happy tubes are seated correct take tool [D] and tighten
bolt grub screws until firm. Not do not overtighten. Assembly complete move to next page.

617TOUHE
ASSEMBLY COMPLETE

717TOUHE
FEATURE’S AND OPERATING OF RECLINER
Operating recliner footrest:
To raise footrest.
Place both hands on armrest pads as indicated in diagram. While leaning back into chair push
on backrest from your hands up to shoulders, while not having any tension in your legs.
To Lower footrest.
Please have backrest in fully upright position, then simply lean forward and use lower muscles
in your legs to push down footrest.
Caution only operate footrest when backrest is in fully upright position.

817TOUHE
FEATURE’S AND OPERATING OF RECLINER
Operating recliner backrest:
To lower backrest.
Please locate on right hand side of seat a looped strap this is used to release pin inside
mechanism of recliner action. Pull on loop and lean back on backrest. Release loop when you
have desired angle on backrest, pin will automatically find a locking position.
To raise backrest.
Simply pull on loop again, lean forward hold onto to loop till chair is back in full upright
position then release. Chair will lock in upright position.

917TOUHE
FEATURE’S AND OPERATING OF RECLINER
FEATURE:
Swivel base.
Complete 360 degree turning circle.

10 17TOUHE
FEATURE’S AND OPERATING OF RECLINER
FEATURE:
Adjustable head rest.
Internal adjustable headrest for variable use.
Please view diagrams below for operation of the adjustable headrest.