Furniture Solutions Henri 19HEN User manual

H:100~78CM
D:81~120CM D:39CM
W:78CM
H:41CM
W:49CM
= Furniture Solutions
=
Imported by Furniture Solutions (Aust) Pty Ltd New South Wales,
Australia.
For any assistance with assembly or for missing parts please contact:
Place of purchase or Furniture Solutions on below
Customer Service (Australia) Phone-1300 794 188
[e-mail]
INSTRUCTION MANUAL
HENRI
RECLINER CHAIR & FOOTSTOOL
CODE: 19HEN
1 of 13

PRE-ASSEMBLY PREPARATION
Avoid use of powered/batt ery drills. Improper use of
drills can irreversible damage to fittings.
30
MINUTES
ALLOW TIME
X2
PEOPLE REQUIRED
2
Before you start:
Choose a clean, level, spacious assembly area. Avoid hard surfaces that may
damage the product
1.
Take care when lifting. Product should be assembled as near as possible to
the point of use
2.
Ensure that you have all required contents for complete assembly
3.
4.Ensure to check all components for any damage before assembly.Please
report any damage found to below, if possible forward images of component
to below
5.Always read the assembly instructions carefully before beginning assembly.
6.Keep all hardware parts and packaging out of reach of small children.
7.Do not over tighten the screws and bolts as this may damage the threads
For any assistance with assembly or for missing parts please contact:
Place of purchase or
Furniture Solutions Customer Service (Australia) Phone - 1300 794 188
Email- [email protected]
19HEN

1
5
3
3
3
PARTS LIST
A
B
C
D
E
F
1PC
4PCS
1PC
M6X20
4mm
Knob/Shaft
1PC
3PCS
M8X35
6PCS
M6X20
1.Seat Cushion
6.Footstool base
5.Chair Base
2.Backrest Cushion 3.Armrest Pads
4.Footstool Cushion
Footstool post
Chair post
6mm
1PC
1PC
2
G
H
4
6
19HEN

4
Please
prepare work area as instructed in page 2:
To Assemble
Footstool:
Identify required
hardware before you start assembly. Note do not over tighten any bolts,
tighten
only until feels firm.
Take footstool cushion [4],
place upside down as per diagram. Next take footstool stem [B] and
aline all 4
holes as indicated in diagram. Then take bolt [A] by hand and insert thru hole in stem
into
threaded hole of footstool cushion and turn 2-3 times to ensure thread on bolt has gripped
threaded hole in cushion. Do not tighten yet. Repeat for other 3 bolts [A] until all bolts are
seated correctly. Once all seated correctly take tool
[H]
and tighten all four (4) bolts until feels
firm. DO NOT OVER TIGHTEN. Then position footstool base [6] on a firm level surface and insert
stem into base as shown in diagram, you will need to ensure tube is inserted squarely, once you
are satisfied all square, with caution sit on footstool top to add the pressure required to lock in
stem and base together.
Move to Chair base Assembly next Page.
4
4
H
6
19HEN

5
To Assemble
Chair, chair base assembly
You will need
the help of another person thru this stage.
As indicated on diagram
place chair base [5] on a flat level surface. Take chair stem [C] insert
thicker
end into chair base, check that it is square. With help of another person pickup chair
seat
cushion and frame [1], locate hole in middle of frame under cushion, insert squarely onto
chair
and stem as indicated in diagram, check that it is fitted correctly should be no
movement in lower frame. Move to backrest assembly
1
5
19HEN

6
To Assemble
Chair, Backrest assembly
You will need
the help of another person thru this stage.
Next
is to fit backrest [2] to seat cushion. You will note that seat cushion can move forward
and backward,
please position seat cushion so you have a clear view of threaded bolt hole in
black frame
at back of cushion, you may need to move leather to view holes. With the help of
another person take
backrest and aline backrest with seat cushion as shown in diagram. Note
on Right Hand Side Facing
you will see a black painted pin extending from frame, please insert
coordinating hole on backrest, next aline threaded hole in seat cushion frame with hole in
backrest on left hand facing side of chair, insert by hand bolt [D] turn 2- times to ensure tread is
seated properly, please do not tighten as yet.
Note this bolt acts as a pivot once fully tighten do not over tighten once advice to tighten is
instructed.
Next as per diagram you will need to fit 2 more bolts (pivots) higher up on backrest, aline
backrest cushion so that holes at top of chair frame match the threaded holes in backrest. Take
bolt [D] insert thru hole in chair frame into threaded hole and by hand turn 2-3 times to seat
thread correctly, once complete repeat for other side. Once both fitted take tool [G] and
tighten all 3 bolts that are in backrest. Note all these bolts act as pivot and only require to be
tightening until thread is not visible. Move to next page for arm pad assembly.
2
1
D
2
1
D
19HEN

33
2
1
E
E
7
To Assemble
armrest pads:
To fit armrest
pads [3] you will be required to pull backrest back to be as flat as possible.
Please
position armrest pad as per diagram, aline holes in chair frame to threaded holes in
armchair
pads, insert bolt [E] into hole of frame and into threaded hole of arm pads, turn 2-3
times
to seat thread correctly. Do not tighten yet. Repeat for other 2 bolts once all three (3)
bolts are fitted, take tool [H] and tighten until feels firm. DO NOT OVER TIGHTEN.
Repeat process for other arm. Move to fit locking arm.
To fit
locking arm:
Please
locate underneath seat cushion on black frame a threaded hole as per the diagram.
Take
locking arm [F] insert threaded end into thread of chair frame and turn 2-3 times to seat
in thread
properly. Note this locking arm acts as a brake system for reclining action on chair,
please
see operating instruction in coming pages. Assembly Complete please see operating
instruction before
you use.
F
19HEN

ASSEMBLY IS COMPLETE
819HEN

FEATURE:
Swivel
base.
Complete
360 degree turning circle.
9
Operation of Recliner:
Locking
of backrest in desired position.
The locking
mechanism is design for variable recline positions, so you can find the preferred
angle for siting.
Turn knob (locking arm) clockwise to lock and anti clockwise to loosen.
FEATURE’S
AND OPERATING OF RECLINER
360°
F
19HEN

Feature of Recliner:
Adjustment of head rest:
Internal Adjustable head rest for variable positions.
Please review diagrams below before operating headrest function.
10
FEATURE’S
AND OPERATING OF RECLINER
19HEN