Furniture Solutions 17CAE15SG User manual

Imported by Furniture Solutions (Aust) Pty Ltd New South Wales, Australia.
For any assistance with assembly or for missing parts please contact:
Place of purchase or Furniture Solutions on below
Customer Service (Australia) Phone-1300 794 188
Email- [e-mail]
INSTRUCTION MANUAL
CAESAR SIDE TABLE
ITEM CODE: 17CAE15SG
117CAE15SG
Imported by Furniture Solutions (Aust) Pty Ltd
10-16 Daisy St,
Revesby, NSW. 2212
www.furnituresolutions.com.au

PRE-ASSEMBLY PREPARATION
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may
damage the product
2. Take care when lifting. Product should be assembled as near as possible to
the point of use
3. Ensure that you have all required contents for complete assembly
4. Always read the assembly instructions carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over tighten the screws and bolts as this may damage the threads
217CAE15SG
20
MINUTES
ALLOW TIME PEOPLE REQUIRED
X2

PARTS LIST
PART CODE
1
TABLE TOP PVA9961E-T
2
TABLE LEG PVA9961E-L
3
X TABLE LEG PVA9961E-XL
317CAE15SG

FIT TABLE LEGS
Prepare product as per page 2:
Position table top upside down on a soft level surface IE: Floor with clean carpet or thick blanket
on harder surface. Note 2 people will be required thru most of the assembly.
When table top [1] is in position take note of the thread holes in base, you will note a grouping of
3 threaded holes in a triangle pattern and a single threaded hole to right of the triangle of holes.
The single threaded hole is to be used to attach the X table leg [3], you will note that the two
single threaded holes are diagonally positioned.
Step 1: Take X table Leg [3] and aline with the thread holes described above, while second person
holds table leg, take bolt [A] with spring washer [B] insert thru hole in table leg and into thread in
hole, ensure you seat thread correctly, by hand turn 2-3 times or until you feel bolt has grip
thread, do not tighten yet, now fit bolt as above on other side of X table leg. Once both bolts are
seated correctly, take Allen Key [C] and tighten both bolts until firm.
Warning over tightening may cause damage to fitting.
Step 2: To fit other table legs [2] ensure you have leg facing away from centre of table top as
indicated in drawing below. Aline all three holes in table leg with three threaded holes in table
top.
While second person hold in position, table bolt [A] with spring washer and fit in same method as
above. Again do not tighten bolts until you have all three bolts properly seated. Once all seated
take Allen Key [C] and tighten until firm. Do not over tighten.
Repeat for second table leg [2]. Assembly complete. Move to next page
417CAE15SG

STEP
2: STAND TABLE ON LEGS
Please note this is a very heavy item and will require 2 reasonably strong people to pick up and
place into position.
One person at each end looking down the length of the table. Please get a good grip and lift table
using your knees straight up into air, now carefully in mid air rotate table over until feet can touch
the floor. Do not lay table on its side to rotate onto feet as you may damage fittings.
To place table in position please move around table until you are mid way the length of table. Pick
up form middle and place table in area to be used.
Warning never drag table always lift as above and with the help of another person.
Dragging can cause damage to product and or your floor surface.
517CAE15SG

617CAE15SG
CARE AND MAINTENANCE
About ceramic material:
Ceramics are generally made by taking mixtures of clay, earthen elements, powders, and
water and shaping them into desired forms. Once the ceramic has been shaped, it is fired in
a high temperature oven known as a kiln. In general, they are hard, corrosion-resistant and
have a higher scratch resistance than glass.
Care Instructions for unglazed ceramic:
To reduce cleaning the use of table clothes and placemats is highly recommend.
Please choose a pH neutral cleaner follow directions on packaging of product for use.
Ensure you remove excess cleaning product and avoid spills onto other items.
Lacquer painted MDF:
No polishing is required for lacquer simply wipe down with a soft clean cloth, recommended
to use a suitable microfiber cloth. For spills and grime build up please use a pH neutral
cleaner. Ensure you remove excess cleaning product and avoid spills onto other items.
Metal lacquer painted brushed steel:
Legs are made up of a sturdy steel tube which has been scuffed up to add character.
No polishing is required for lacquer surface on metal, simply keep dust free by using a soft
clean cloth, recommended to use a suitable microfiber cloth. For spills and grime build up
please use a pH neutral cleaner. Ensure you remove excess cleaning product and avoid spills
onto other items.

717CAE15SG
SAFETY WARNINGS AND ADVICE
Notices and Advice
Please be advised that materials used in your furniture are not impervious to neglect, acts of
god, abuse, alcohol spills, improper use of chemicals such as bleach or any solvent based
products
.
Please be advised that heat sources such as direct sunlight, log fires, heaters and air
conditioners can have adverse affects on your furniture.
Please be advised that fitting, bolts, nuts and or screws should be checked periodically to
ensure they have not loosened over time. Remember do not overtighten.
Please be advised that products are limited in design for residential use only and are not
suitable for commercial use.
DO NOT
•Place in direct sunlight.
•Place in close proximity to open flame or heaters.
•Place in direct line of air conditioning ducting.
Safety warnings
•DO NOT:
•drop, drag or strike table surface
•sit or stand upon the table surfaces
•place heavy objects on glass
•place very hot or cold items on the table surface unless adequately thick table mats are
used to prevent such items coming in contact with the surface
•scratch the surface or using as a chopping surface
•allow children to play under tables
•Never drag table always move by lifting
•Clean only as per instructions on previous page. Do not use washing powders or any
other substances containing abrasives that may potentially scratch the surface
CHAIRS AND STOOLS
•Do not:
•Use chair/stool as a ladder
•Climb on the chair/stool
•Stand on the foot-rest of the chair, as this could lead to the stool becoming unbalanced
and overturning

817CAE15SG
WARRANTY DETAIL
1 Year Warranty
A one (1) year warranty applies to product against any defect associated with faulty
workmanship for a period of (1) year from date of purchase.
Furniture Solutions accepts no responsibility for defects caused by incorrect assembly,
mishandling, acts of god, general wear & tear, stains from spills/vegetation,
chipping/scratching, exposure to extreme heat/cold, mould/mildew, hardware corrosion,
misuse of the products & defects caused by failure in duty of care for the product in
accordance with the care instructions. Warranty only extends to original purchaser and is
not transferable, except when given as a gift.
Notice:
While every effort is made to use quality materials our products are limited in design for
domestic use only & are not suitable for commercial use.
Care should be taken not to place product near heat sources.
Duty of care:
While every attempt is made to supply product using quality components there is always a
need from consumer to help ensure long life of use for product. Instruction manuals are
designed with the nature of materials used in construction of the product.
*Proper use of item only what it is designed to do
*Regular maintenance and cleaning
In areas of high content of salt air, pollution & moisture require more frequent cleaning.
Claim management:
To make a warranty claim, customers can either contact the retailer where the purchase was
made or Furniture Solutions on contact details below. Proof of purchase will be required
before proceeding with any claim. In the case of product defects providing photos may be
able to speed up processing of the claim. If missing parts please refer to assembly
instructions for identification of said part and contact either of the above.
“Our goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and for compensation
for any other reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure does not
amount to a major failure”.