FUTABA GY701 User manual

1M23N23902
INSTRUCTION MANUAL

TABLE OF CONTENTS
TABLE OF CONTENTS
• Precautions ----------------------------------3
•
Warranty and Repair Service (in U.S.A.) --8
• Introduction ---------------------------------9
• Features --------------------------------------9
• Contents ----------------------------------- 11
• Specications ----------------------------- 14
• Recommended Servos ------------------- 15
• Replacement and Optional Items ------- 15
•
Connecting the GY701 to your Receiver 16
• LED Indicator Description -------------- 19
• Mechanics Preparation------------------- 20
• Opening Screen --------------------------- 22
• Home Screen ------------------------------ 23
• Warning Display -------------------------- 30
• Edit Screen -------------------------------- 32
• Gyro Basic Setting ----------------------- 34
• Gyro Sensor Installation ----------------- 36
•
Tail Rotor Servo Installation and Setup -- 37
• Before Flight Checklist ------------------ 40
• Adjustments During the Test Flight ---- 41
• Using Normal Mode --------------------- 43
• Setting the Gain --------------------------- 44
• Governor Basic Setting ------------------ 46
• Mounting the Magnet and Sensor ------ 54
• Fuselage Setting Precautions ----------- 58
• Governor Operation ---------------------- 60
• Governor Speed Setting ----------------- 62
• S.BUS Basic Setting --------------------- 64
• Gyro Expert Setting ---------------------- 68
• Governor Expert Setting ----------------- 76
Meaning of Special Markings
Pay special attention to safety where indicated
by the following marks:
󾻯DANGER - Procedures which may lead to
dangerous conditions and cause death/serious
injury if not carried out properly.
󾻯WARNING - Procedures which may lead to a
dangerous condition or cause death or serious
injury to the user if not carried out properly, or
procedures where the probability of superficial
injury or physical damage is high.
󾻯CAUTION - Procedures where the possibility
of serious injury to the user is small, but there is
a danger of injury, or physical damage, if not car-
ried out properly.
󾻭: Prohibited 󾻫: Mandatory
Gyro : Instructions for gyro function
Governor
: Instructions for governor function
Technical updates and additional programming
examples can be found at:
www.futaba-rc.com/faq
2
3
PRECAUTIONS

PRECAUTIONS
PRECAUTIONS
󾻯WARNING
Failure to follow these safety precautions may
result in severe injury to yourself and others.
• Read through the entire manual before operat-
ing this product.
BEFORE EACH FLIGHT:
󾻫Always check the transmitter and receiver bat-
tery voltage to ensure they have enough remain-
ing capacity to complete the flight.
󾻫Always exit programming mode before at-
tempting to fly the model.
󾻫Only use the GY701 with a 2.4GHz system
such as the Futaba FASST system, or a PCM
system. Use with a FM system is strongly dis-
couraged since interference can cause serious
operational problems.
Gyro operating precautions: Gyro
󾻭The GY701 requires 5-10 seconds to initial-
ize when the power is turned on. Do not move
the helicopter and do not move the tail rotor
stick during this initialization or the gyro may
not initialize properly. Once the initialization
process is complete, the tail rotor servo will
move to the left extent and then to the right
extent. This will occur twice. The indicator
light will change to solid red for AVCS Mode
or solid blue for Normal Mode.
󾻫Verify that the gyro is operating correctly.
󾻫Verify that the gyro compensates in the correct
direction before flight. If the compensation direc-
tion is incorrect the model will pirouette uncontrol-
lably, at a very high rate.
󾻫Verify that the gyro is operating in the desired
mode.
󾻫Verify that the gyro mounting pads are in good
condition.
󾻫Verify that the gyro wires are not contacting
the frame of the helicopter.
󾻫The servo type parameter within the GY701
must match the type of servo you are using. In-
correct setting may damage the GY701 or the
servo, possibly resulting in a loss of control during
flight.
󾻫Always ensure that there is some slack in the
gyro cables to help maximize performance. Al-
ways use the supplied gyro mounting pads to at-
tach the gyro to the helicopter mechanics. Do not
use a strap that encompasses the GY701 sensor.
This may affect the overall performance of the
gyro.
󾻫Always allow the gyro to adjust to the sur-
rounding environmental temperature before flight.
A large temperature change during use will cause
drift and other operational issues.
󾻭The GY701 sensor uses a high strength alumi-
num die cast case. Do not allow anything to touch
the gyro case as it may cause a short circuit.
󾻫If you are switching between Normal Mode
and AVCS Mode in flight, please keep in mind
that you must have the gyro re-learn the center
position after making a trim change within the
transmitter. To memorize the new center position
simply flip the gain switch on the transmitter three
times between Normal Mode and AVCS Mode
(NormalAVCSNormalAVCS) within one
second. The tail rotor servo will center indicating
that the new center position has been memorized.
4
5

PRECAUTIONS
PRECAUTIONS
󾻫When operating the gyro in AVCS Mode, all tail
rotor compensation and revolution mixing must be
disabled and any tail rotor offsets for flight modes
must be disabled.
󾻫When the GY701 is operated in AVCS mode
the tail rotor servo will not center when the stick
is released. This is normal operation for AVCS
mode. The servo may also move to the extent
while the model is being carried out to the flight
line. Before take off, you must center the tail rotor
servo by moving the tail rotor stick full left, then
full right, back to full left and then allow the stick
to center within one second. You can also visually
center the tail rotor pitch slider by using the tail
rotor stick.
󾻭Do not drop the GY701 sensor onto a hard
surface or subject the GY701 sensor to a strong
shock as this may damage the sensor. Always
use the supplied mounting pads or the Futaba
replacement mounting pads available from your
local hobby dealer.
Governor operating precautions:
Governor
󾻫Always set battery fail safe function at the
GY701. Since the GY701, when used, controls
the throttle, the battery fail safe function that is in
a receiver will not be used.
󾻫Throttle fail safe function (transmitter setting):
Use the fail safe function for the channel that
turns the governor on and off to set the fail safe
position to the point at which the governor is
turned off. With this setting, when the system en-
ters the fail safe state, the governor will be turned
off and the receiver throttle signal (fail safe posi-
tion preset) will be output directly.
6
7
󾻫When using the condition hold function, trans-
mitter’s function), always set the throttle servo
maximum operating point to less than the point
at which the governor is turned on. Depending on
the conditions, this setting will turn on the gover-
nor and prevent the engine from exceeding the
set speed even when condition hold is set.
󾻫At the beginning of flight, keep the governor in
the off state by setting the throttle stick to maxi-
mum slow side.
󾻫When the model is on the ground, lower the
pitch to the position at which the model does not
try to lift off. Do not take your eyes off the model.
When the governor operates and the rotor speed
increases the lift also increases causing the
model to try lift off , depending on the pitch posi-
tion.
󾻫Check the sensor output not only when install-
ing the sensor but periodically. Since the magnet
rotates at high speed, it is subjected to a large
centrifugal force. Check the magnet output and
mounting state after about every 10 flights.
󾻫If the model begins to shake during operation,
immediately turn off the governor. The carburetor
design, etc. may cause the engine to operate un-
stable. If this occurs, lower the maximum speed
setting to the range over which there is no prob-
lem.

WARRANTY & REPAIR SERVICE (IN U.S.A.) INTRODUCTION
If any difficulties are encountered while setting
up or operating your GY701, please consult the
instruction manual rst. For further assistance you
may also refer to your hobby dealer, or contact the
Futaba Service Center at the web site, fax or tele-
phone number listed below:
www.futaba-rc.com or www.hobbyservices.com
Fax [phone],Tel [phone]
If you are unable to resolve the issue, pack the
system in its original container with a note en-
closed and a thorough, accurate description of the
difculty. Include the following in your note:
• Symptoms (including when the problem occurred)
• System (Transmitter, Receiver, Servos and model
numbers)
• Model (Model name)
• Model numbers and quantity
• Your Name, Address and Telephone number
Send the respective items to the authorized Futaba
Service Center Address below:
Futaba Service Center
3002 N Apollo Drive Suite 1
Champaign, IL 61822
8
9
FEATURES
• Combined Gyro and Governor in one box. Indi-
vidual either Gyro or Governor working mode
are supported.
• The fastest operation scheme is utilized both the
Gyro and Governor section.
• Low prole, small size and lighter weight.
• Small size of the combined one box gyro and
governor controller, 44 x 29 x 12mm, 13 g
• Using the 128 x 36 dots graphical white color
OLED (Organic Light Emitting Display), high
brightness and contrast.
• Easy setting divided by Basic and Expert editing
menu. The basic setting is for initial setting and
Expert setting is for precise setting.
•
Firmware can be updated from PC through CIU-2.
• Supporting the S.Bus connection. Only one
wire connection to the receiver can operate the
GY701.
The Futaba© GY701 is combined heading hold
AVCS gyro and head speed governor in one box.
Its cutting-edge MEMS (Micro Electro Mechani-
cal System) sensor design, ultra high-speed pro-
cessing speed and advanced PID control algorithm
put it a quantum leap ahead of all other heading
hold gyros in size, weight and performance. The
GY701 has been optimized to work for model he-
licopter competition.

FEATURES CONTENTS
Your GY701 includes the following components:
Type of set
• Gyro & Governor set w/BLS251
• Gyro & Governor set
• Governor set
• Gyro set
SET CONTENTS
GY701 Control Amp
*Mini Screwdriver
*Dust Covers (x3)
XXXX
Gyro Sensor
*Mounting Pads (x3) X --- X X
Governor Sensor
*Sensor Mounting Hardware
*Magnet (x2)
--- X X X
BLS251 Servo
*Servo horn and mounting parts --- --- --- X
Extensions (Black/Red) 1122
X: supplied ---: not supplied
10
11
• Gyro section
• Advanced and adaptive PID operation is utilized
• Small and low prole gyro sensor. 2 colors LED are
installed on the top surface. Using the Aluminum
Alloy metal case. 21 x 21 x 8mm, 14.5 g
• Wide operation dynamic ranges up to +/- 1,200
deg/sec.
• 3 kinds of servo type are supported
• 3D and F3C operation mode is selectable
• The Feed forward operation is utilizing. Pitch sig-
nal can be added to the gyro operation.
• New operation algorism achieves the more consis-
tent pirouette and smooth Yaw control .
• Governor section
•Advanced and adaptive PID operation is utilized
•Fastest operation.
•Wider revolution control ranges, 1000 rpm-3000
rpm
•Both digital and analog servo can be selected
•Revolution compensation by Yaw rate is installed
•Governor or Rev. Limit mode selectable
•New operation algorism achieves more faster and
smooth revolution control .
•Back plate sensor can be selected by the option (for
OS-91, OS-55, OS-50)
• Other function
• Maximum revolution memorize
• Engine runtime integration
• OLED power saving
• LED on/off selectable

CONTENTS
CONTENTS
Extensions: Extension (Black)
Extension (Red)
SENSOR THRO MXTR
r.p.m 1 r.p.m 2 r.p.m 3
m.trim GOV on GOV off
on / off
Tx
GV-1
& Sx SENS.
r.p.m THRO
m.trim
BLS251 Servo
Sensor Mounting StayGY701 Control Amp
Mounting Pads
2mm Thick (three)
Adjustment Screwdriver
Gyro Sensor
Magnet
Dust Cover
Governor Sensor
12
13

SPECIFICATIONS RECOMMENDED SERVOS
.91 Size Helicopters
Futaba S9254 Digital Servo Heli: FUTM0224
(280Hz/1520μS)
Futaba S9256 Digital Hi Speed: FUTM0226
(560Hz/760μS)
Futaba BLS251 Brushless Heli Servo: FUTM0521
(560Hz/760μS)
REPLACEMENT & OPTIONAL ITEMS
Futaba PC Interface CIU-2 for GY701: FUTM0951
FSH64 GY520 Extension 200 mm (2): FUTM4664
FSH65 GY520 Extension 350 mm (2): FUTM4665
FSH66 GY520 Extension 55 mm (2): FUTM4666
FSH67 GY520 Extension 80 mm (2): FUTM4667
FSH68 GY520 Extension 130 mm (2): FUTM4668
FSH69 GY520 Mounting Pad: FUTM4669
2x22x22 mm (10)
FSH70 GY520 Mounting Pad: FUTM4670
3x22x22 mm (10)
FSH71 GY520 Shield Plate: FUTM4671
1x22x22 mm (3)
Width (Controller): 1.14in [29mm]
(Gyro sensor): 0.83in [21mm]
(Speed sensor): 0.30in [7.5mm]
Length (Controller): 1.73in [44mm]
(Gyro sensor): 0.83in [21mm]
(Speed sensor): 0.63in [16mm]
Height (Controller): 0.55in [14mm]
(Gyro sensor): 0.31in [8mm]
(Speed sensor): 0.39in [10mm]
Weight (Controller): 0.459oz [13g]
(Gyro sensor): 0.353oz [10g]
(Speed sensor): 0.141oz [4g]
Maximum* Operating Voltage : 3.8V to 8.4V DC
Current Drain: 80mA
Selectable Servo Frame: 70Hz, 280Hz and
570Hz(Gyro only) Rate
Center Pulse Width: 1520µS (70Hz & 280Hz
Frame Rate)
Flight Mode: User selectable F3C
or 3D (Gyro)
Control Resolution: 0.1Hz (6rpm)
(Engine speed)
Speed stability accuracy: 1%
Speed Control Range: 1,000-3,000rpm
(Rotor speed)
Operating Temperature: 14°F to 113°F
(-10°C to +45°C)
Control System: Digital advanced control
Sensor: Vibrating structure gyro/
Magnetic sensor
(Gyro/Governor)
Angular Velocity Range: ±1,200 Degrees Per
Second (Gyro)
* The maximum operating voltage listed only applies to
the GY701. Always verify that your receiver, servos,
tail rotor servo, switch and any other electronic com-
ponents used in your installation are capable of operat-
ing at the voltage you plan to use.
14
15

CONNECTING THE GY701 TO YOUR RECEIVER
CONNECTING THE GY701 TO YOUR RECEIVER
LCD Display
• Displays the set data and
operation status.
Edit Keys
• Used when setting data.
• Operated by pushing with the
accessory mini screwdriver.
• Connect the GY701 and the
receiver with the supplied ex-
tensions. [(3) to (6)]
When using an S.BUS re-
ceiver, (4) to (6) are not con-
nected.
• GY701 power requirement:
4.8V (from receiver)
16
17
(1) Gyro: Gyro
• Connect the gyro sensor.
*Insert the sensor connector until it
is firmly locked.
(2) Rsen:
Governor
• Connect the speed sensor.
Receiver
(3) Rin/SB:
• S.BUS receiver: Connect to the S.BUS out-
put of the receiver.
• Other than S.BUS receiver: Connect to the
rudder channel output. Gyro
(4) Tin:
Governor
• Connect to the throttle channel output.
(5) Gain: Gyro
• Connect to the gyro gain channel output.
(6) rpm:
Governor
• Connect to the governor speed channel
output.
(7) Tout:
Governor
• Connect the throttle servo.
(8) Rout: Gyro
• Connect the rudder servo.
(1)
(2)
(7)
(8)
(3)-(6)

CONNECTING THE GY701 TO YOUR RECEIVER LED INDICATOR DESCRIPTION
Slow Flash: 1/2 Second or longer
Fast Flash: 1/4 Second or shorter
LED Indicator
CONDITION LED INDICATOR DESCRIPTION
Initialization Red Double Flash No Receiver Pulse or Sensor
Error
Slow Blue Flash Warm-Up
Fast Blue Flash Sensor Initialization
Slow Red Flash Governor Warning
Program-
ming
Blue Single Flash Parameter Programming
Mode
Slow Blue Flash Rudder Limit Setting Mode
Operating Solid Blue Normal Mode, Ready for
Flight
Solid Red AVCS Mode, Ready for
Flight
Slow Violet Flash Offset from the Neutral Posi-
tion (AVCS)
Fast Blue or Red
Flash
Gyro is Rotating
Connect the supplied extensions to the GY701
connecter. Route the wires through the helicopter
mechanics and connect them to the appropriate
receiver channels. To determine the appropriate
receiver channels please check your transmitter’s
instruction manual. Using wire mounts, wiring
xtures molded into the helicopter, or hook and
loop material, route the extensions to the receiver.
Ensure that the extensions leading to the receiver
cannot become entangled in rotating components
and make sure the extensions are not rubbing
against metal or carbon ber which may damage
the wires.
Once the power system is installed into your heli-
copter please move onto the later section to learn
how to program the gyro.
18
19

MECHANICS PREPARATIONS
MECHANICS PREPARATIONS
• Vibration will affect the GY701’s overall perfor-
mance. All rotating components on the helicop-
ter should be balanced to minimize vibrations in
ight. Ensure that your motor is running smooth
and all vibrations have been addressed before
installing and test flying the GY701.
󾻯WARNING
󾻫Newer high end servos and other radio
equipment are capable of placing large de-
mands on the power systems in use today.
When using a regulator you must ensure that
the regulator is capable of delivering the cur-
rent demands of the equipment you have se-
lected. In addition to this make sure the wiring
and switch you have selected are capable of
handling high current draws.
󾻫Even though the GY701 is a high performance
gyro and governor it will be necessary to ensure
that the helicopter mechanics are also in optimum
operating condition. Please use the guidelines
below and address all issues before installing and
test flying the GY701.
• The GY701 must be used with a rigid tail rotor
drive system. Any modern torque tube or belt
drive system should be adequate. Do not at-
tempt to fly the GY701 using a wire driven tail
rotor system.
• Always ensure the drive gears, torque tube,
pulleys, belt, bearings and shafts are in proper
working condition. If any of these items are
damaged or worn they must be replaced.
•
The linkage rod, tail rotor bell crank, pitch slider
and tail rotor grips must operate without friction
to obtain the best performance from the GY701.
If any binding is present it must be fixed before
the helicopter can be flown. Binding in the tail ro-
tor control linkage will decrease the performance
of the GY701 gyro and this may also shorten the
servo lifespan. Please take the time now to ensure
the tail rotor system on your helicopter is working
correctly, without friction or binding. Gyro
20
21

OPENING SCREEN HOME SCREEN
22
23
The GY701 starts the initializing process at turned
on the power. After finished the initializing, the
GY701 starts the operation and moves to the
home screen.
Boot up display
The OLED shows below the screen. The upper
line indicates the identication code of the GY701
and below of the line indicates the rmware ver-
sion.
Initializing display
The pirouetted helicopter images are displayed
during initializing. After completed the initialize,
the rudder servo moves CW-> CCW as the initial-
ize nished sign and move to home screen. The
helicopter must not be moved during the initial-
izing process.
After finished the initialize sequence, OLED
changes the display to Home screen. There are 3
kinds of the Home screen related by the operation
mode. The home screen shows the information as
follows.
Initial Home screen
•Gyro+Governor mode
2. Stop boosting
1. Neutral compensation
3. Gyro working mode
4. Gyro gain
5. on/off switch
6.Yaw rate comp.
8. Orientation indicator
7. Battery voltage
•Gyro only mode •Governor only mode
9. Setting
revolution
1. Neutral compensation Gyro
It indicates the function of the neutral compensation
at the pirouette stop is active. No display shows at the
function inhibited.
2. Stop boosting Gyro
It indicated the function of the gain boosting at the
pirouette stop is active. “G” character is displayed at
the function inhibited.

HOME SCREEN
HOME SCREEN
24
25
3. Gyro working mode Gyro
It indicates the gyro working mode either AVCS or
Normal mode. The inverse “A“ character is displayed
at the rudder neutral is offset.
At the AVCS
mode
At the normal
mode
Neutral offset at
AVCS mode
At the AVCS mode, move the rudder stick more than
2 times left and right full within the period 1 second
and return the stick to neutral position, the rudder
servo retrieves the neutral position. The OLED shows
the "--------" display at this condition.
Reset AVCS
Hold the rudder stick to neutral and move the gyro
gain channel, Normal→AVCS→Normal→AVCS
within the 1 second period. After done the process,
the rudder stick neutral is memorized to the GY701 to
match the rudder stick neutral. This operation is use-
ful for rudder neutral re_trimming from normal mode
to AVCS mode. After nished the operation, OLED
shows "********". The GY701 always renews the
rudder neutral position at the turned on the power
with AVCS mode. The rudder stick must be stayed
neutral position during the starting up.
Reset rudder neutral
4. Gyro gain Gyro
It indicates the gyro working gain.
5. on/off switch
Governor
It shows the switch condition of the governor. The
governor is active at ”On” displayed.
6.Yaw rate comp.
Governor
It indicates the revolution compensation at the pirou-
ette is active. No display shows at the function inhib-
ited.
7. Battery voltage
It indicates the battery voltage. The Low battery is
displayed at below 3.8 volts.
8. Orientation indicator
It supports as the operation guide. Push the key
switch below this indicator, changes the editing mode.
9. Setting revolution display
Governor
It displays the setting revolution of the governor. It
shows only at the governor only operation mode.

HOME SCREEN
HOME SCREEN
26
27
Revolution display
Governor
The battery voltage display is changed to engine
revolution display at starting the engine running,
and return to battery voltage display at the engine
stop automatically. The revolution mode can be
selected either main rotor revolution or engine
revolution. The rpm character starts slow blinking
at the governor starts the operation and fast blink-
ing at the revolution reached to +/- 2% of the set-
ting revolution. The rpm character changes to in-
verse character at the revolution within +/- 1% of
the setting revolution as the revolution is locked.
At the governor only mode, the revolution is dis-
played on the top of the display line after running
the engine.
Sub_Home screen
At the home screen display, the display of below
the line is scrolled to Battery voltage→Max.
revolution→Engine runtime→OLED display
mode→LED display mode→Operation mode by
pushing the mode + or - key.
1. Max. revolution
Governor
It memorizes the maximum engine revolution at the
operation. The display is changed to Max. revolution
by pushing the mode + key. The revolution data is
stored to the memory. The data is reset by pushing the
data + or – key for more than one second.
2. Engine runtime
Governor
It displays the engine runtime integration. The display
is changed to runtime mode by pushing mode + key
2 times from home screen. The display unit is second
until 100 hours as xxHxxMxx, over 100 hours, min-
utes as xxxxHxxM. The display is reset by pushing
data + or – key for more than 1 second.
3. OLED display mode [default: Saver]
It selects the OLED display mode. The Saver mode
reduces the brightness and saves the power consump-
tion after no editing for 60 seconds. The brightness is
returned by pushing any key. The Light mode always
lights the maximum brightness.

HOME SCREEN
HOME SCREEN
28
29
4. LED display mode [default: ON]
It selects the display mode of the LED on the gyro
sensor. The LED is light at ON setting, turned off
by Off setting for power saving. The mode can be
changed by pushing the data + or – key.
5. Operation mode [default: Gyro+Gov]
It sets the operation mode of the GY701. Set to “Gov-
ernor” when the gyro sensor is not installed and set
“Gyro” when the governor sensor is not installed. Set
“Gyro+Gov” when the both gyro and governor sensor
are installed. Mode is changed by pushing the data +
or – key. The home screen is changed after changed
the operation mode. The “SensorER” is displayed
when the gyro sensor is not installed and the opera-
tion mode is set “Gyro” or “Gyro+Gov” mode. Push
any key to escape this display and set the operation
mode is to be “Governor”.
When the operation mode is changed, it must be
needed the reboot the GY701. During the operation,
it is not allowed to change the operation mode.

WARNING DISPLAY
WARNING DISPLAY
30
31
Governor warning display
Governor
The warning symbol is displayed when the gov-
ernor is on condition at turned on the power. The
governor is never activated at this condition. The
governor can be working condition after off con-
dition is recognized. The governor must be off
condition at starting the engine.
Input error Gyro
It indicates the no rudder or throttle signal input.
The GY701 does not work at this condition.
Sensor error Gyro
The gyro sensor does not work collect. The gyro
does not work at this condition.
Low battery
It displays at the battery voltage becomes less
than 3.8 v. The low battery is recognized for more
than 1 second, the governor is low battery condi-
tion and the governor operation is stop. If the
B/FS function is activated, the throttle servo is
moved to setting position by B/FS function. The
B/FS condition is reset for 30 seconds by moving
the throttle stick to low full. Throttle servo can
be controlled by stick. After 30 seconds passed,
getting into B/FS condition again. This sequence
lasts forever. The helicopter should be landing im-
mediately if the B/FS condition.

EDIT SCREEN
EDIT SCREEN
32
33
The edit mode is changed to Gyro basic, Gover-
nor basic, S.Bus basic mode by pushing the data+
or- key. These modes set the basic operation set-
ting for initial ight. Pushing the mode + or – key
for more than 1 second at the gyro or governor
screen, the editing mode is changed to the expert
mode, the precise setting can be done by this
mode. Pushing the mode+ or – key for 1 second
again, the editing menu is returned to basic menu.
The setting of the governor functions are skipped
at the gyro only mode or the gyro function are
skipped at the governor only mode as well.
Pushing the mode+ or – key at basic or expert
mode, the edit menu is scrolled and the parameter
can be set on the each menu.
During the home screen, the display is changed to
Max. revolution→Engine runtime→OLED dis-
play mode→LED display mode→Operation mode
by pushing the data+ or - key.
The below the diagram shows the edit sequence.
The instruction describes the Gyro+Governor
mode after.
Push DATA
+/– key
Push MODE
+/– key
Push MODE +/– key
for 1 second
Max. revolution
Home
screen
Engine runtime
OLED display mode
LED display mode
Operation mode
Gyro Basic Gyro Expert
Governor Expert
S.Bus Basic
Governor Basic

GYRO BASIC SETTING
GYRO BASIC SETTING
34
35
It sets the gyro’s fundamental functions. The
menu (4) Servo limit point setting should be set
rst with other menu.
(4) Limit setting [default: 100%, setting
range: 50 〜150%]
Adjusting the maximum servo through. Set the
amount to be not interacted the rudder linkage.
Move the rudder stick right (left) maximum. At
this condition, the servo increased the move-
ment by pushing the data+ key, decreased by
pushing the data- key.
(1) Start display
The editing menu are scrolled
every pushing the mode + or
– key.
(2) Servo type [default: DG:1520]
Selection of the servo type is to be used. The
servo type is changed to Digital 1520Digital
760Analog by pushing data+ or – key.
DG 760: BLS251, S9256, S9251
DG 1520: BLS254, BLS257, S9254, S9257
(3) Gyro direction [default: Normal]
Setting the gyro operation direction. Set the direc-
tion as the gyro operates the servo to right direc-
tion when the helicopter moves to left. The direc-
tion is changed by pushing the data+ or – key.
Push MODE
+/– key
󾻯WARNING
󾻫This parameter must match the type of ser-
vo you are using. Incorrect setting may damage
the GY701 or the servo, possibly resulting in a
loss of control during flight.
󾻯WARNING
󾻫Verify that the gyro compensates in the cor-
rect direction before flight. If the compensation
direction is incorrect the model will pirouette
uncontrollably, at a very high rate.
(5) Flight mode [default: F3C]
Selection of the ight style. F3C mode is more
precise rudder control, the 3D mode is more
active rudder control, pirouette speed is faster
than F3C mode. The mode is changed every
pushing the data+ or – key.
Pirouette rate at AFR100% to full stick:
F3C = 450 deg/sec
3D = 720 deg/sec
󾻯WARNING
󾻫When using the GY701 for the first time, or
when making changes in the throw of a servo,
always perform the limit setting operation.

GYRO SENSOR INSTALLATION TAIL ROTOR SERVO INSTALLATION AND SETUP
TROUBLESHOOTING
If you experience erratic gyro operation (drifting,
not holding well or inconsistent pirouette rate),
please follow the troubleshooting tips listed below.
1. Always verify that your model’s tail rotor control
and drive system are working correctly.
2. Electromagnetic interference could affect the
gyro or tail rotor servo. Mount the gyro in a dif-
ferent location, away from the electronic speed
control, servos and drive motor.
3. The trouble may be caused by vibration. Verify
that your helicopter’s components are bal-
anced. If problems persist, try mounting the
gyro in a different location.
The gyro sensor should be mounted on a rigid
platform, at least 6in [152mm] away from a Ni-
tro Engine. It is not necessary to mount the gyro
near the main shaft of the helicopter but it is very
important that the mounting area chosen is rigid.
Please refer to your helicopter manufacturer’s in-
structions for recommended mounting locations.
Installing the gyro sensor
The GY701 is supplied with three 2mm Mounting
Pads. When mounting the gyro in a larger electric
or .50 through .91 size nitro helicopter we recom-
mend using a supplied 2mm Mounting Pad.
2mm Mounting Pads
Gyro Mount
Gyro Sensor
Following your transmitter instructions, pro-
gram your transmitter as follows:
Enable the gyro function within the transmit-
ter.
Set the gyro mode to AVCS (GY) within the
transmitter.
Set the remote gyro gain to 70% AVCS in the
transmitter for the Normal and Hold flight
conditions and use 40% AVCS for all idle up
conditions. See “Setting The Gain” section
later in this manual for more details.
Set the Tail Rotor ATV/EPA to 100% for both
left and right.
Set D/R to 75% for both left and right. This
will reduce the maximum pirouette rate.
Make adjustments to these values once the
initial test ight has been completed.
It is recommended that you run 30% soften-
ing expo on the tail rotor channel.
󾻯WARNING
󾻭Do not connect the tail rotor servo to the gyro
until the servo type has been selected. Operating
the servo using the incorrect setting may damage
the GY701 or the servo.
Once these steps are completed, turn the receiver
power on and allow the gyro to initialize. Follow
the instructions within the “Gyro Basic Setting”
section of the manual and select the Servo Type
that matches the servo you have chosen to use.
Power down the receiver for now.
36
37

TAIL ROTOR SERVO INSTALLATION AND SETUP
TAIL ROTOR SERVO INSTALLATION AND SETUP
Install the tail rotor servo into the mechanics
and connect the servo to the gyro. Remove
the servo arm screw from the servo. Turn the
receiver power on and allow the gyro to ini-
tialize. Enter the “Gyro Basic Setting” mode
and go to parameter (4) “Servo Limit Point
Setting”. While in the servo limits parameter
the servo will remain centered.
90°
Place an appropriate servo arm onto the servo
and ensure that it is perpendicular to the tail
rotor pushrod as shown. Remove the unused
sides of the servo arm.
Install the control ball supplied with your he-
licopter onto the servo arm. For larger electric
models or nitro powered models we recom-
mend placing the ball 13.5mm from center.
Once the control ball has been installed place
the arm back onto the servo ensuring that it is
perpendicular to the tail rotor pushrod. Install
the servo arm screw.
13.5mm
Follow the instructions within the “Servo
Limit Point Setting” section and set the servo
limits for the tail rotor servo. Hold the tail
rotor linkage over the linkage ball to avoid
damaging the servo. Once the limits are set
you can place the linkage onto the linkage
ball. When using AVCS mode the optimum
setup is to have 0° of pitch with the tail rotor
servo centered and use all of the available
pitch range in the tail without binding.
Turn the receiver power off to exit program-
ming mode and then turn the receiver power
back on. Once the gyro has completed initial-
ization move the tail rotor stick to the right
on the transmitter and verify that right (clock-
wise rotation) tail rotor pitch is inputted to
the tail rotor blades. If left tail rotor pitch is
inputted to the tail rotor blades, then it will
be necessary to reverse the tail rotor channel
in the transmitter.
Pick the helicopter up by the main shaft
and rotate the mechanics counter-clockwise
(from the top). The gyro should compensate
by adding clockwise rotation pitch to the tail
rotor blades. If the gyro compensates by add-
ing counter-clockwise rotation pitch to the
tail rotor blades then it will be necessary to
reverse the “Gyro Direction” setting within
the gyro (refer to the “Gyro Basic Setting”
section earlier in this manual).
If you are going to y AVCS Heading Hold mode
exclusively, then the gyro setup is now complete.
38
39