WARNING
If using a power switch, always connect it between
battery and PS-10.
s)FCONNECTINGTHESWITCHBETWEEN03ANDRECEIVERSSINCEVERYSMALLCURRENTmOWSINTO03EVENIFITISTURNEDOFFITWILLCAUSEOVERDISCHARGINGOFABATTERYDo not connect PS-10 and other regulators or
batteries simultaneously.
s-ULTIPLECONNECTIONMAYCAUSESMOKElREANDDAMAGENever connect the battery in reverse.
s2EVERSECONNECTIONMAYCAUSESMOKElREANDDAMAGEAlways fix the PS-10 securely to the fuselage of the
airplane or helicopter.
s)FTHECONNECTORWORKSLOOSEDUETOVIBRATIONANDSHOCKOPERATIONWILLBEIMPOSSIBLEANDTHEREISTHEDANGEROFACRASHDo not wrap the PS-10 in sponge, etc.
s3UCHWRAPPINGWILLCAUSEALOSSOFCOOLINGEFFECTANDTHESPECIlEDPERFORMANCESWILLNOTBEOBTAINEDDo not continue to operate when the servo is locked
or the rated output of the PS-10 is exceeded.
s)FA
PROTECTIONCIRCUITOPERATESANDSTOPSTHESUPPLYOFPOWERTOTHERECEIVERANDSERVOS
OPERATIONWILLBEIMPOSSIBLEANDTHEREISTHEDANGEROFACRASH
7HENTHEPROTECTIONCIRCUITHASOPERATEDREMOVETHECAUSEOFTHEOVERLOADANDWAITABOUTHOURBEFORERESUMINGUSE
CAUTION
Do not bend the flange with unreasonable force.
s4HEmANGEMAYBEBROKENRegulator for Receiver
INSTRUCTIONMANUALThank you for purchasing a PS-10 regulator for receiver.
When you want to use an ordinary 4.8V rating receiver and servos with a high-
voltage (HV) rating battery (LiFe or LiPo), you can step down the receiver and
servo power to 5.2V by connecting the PS-10 between the battery and the receiver.
[PS-10 BR5.2 Rat ings]
2EGULATORFOR2ECEIVERs-AINAPPLICATION0OWERSUPPLYFOR6RATINGRECEIVERANDSERVOSs)NPUTVOLTAGERANGE6^6s/UTPUTVOLTAGE6s2ATEDOUTPUTCURRENT!-AX!SECs/PERATINGTEMPERATURERANGE^#s3TORAGETEMPERATURERANGE^#s$IMENSIONSXXMMs7EIGHTGU sa g e Pr e c a u t i on s
Con ne c t io n
s&OR'(ZSYSTEMONLY$ONOTUSE03FORANYSYSTEMSOTHERTHAN'(ZSYSTEMs!LWAYSUSE03BETWEENABATTERYANDARECEIVER)TCANNOTBEUSEDBETWEENARECEIVERANDASERVOs5SETHE03WITHINlVESERVOSASTHESTANDARD(OWEVERTHEMAXIMUMNUMBEROFSERVOSWHICHCANBEdriven by it differs depending on the servo and conditions to be used. Always use the PS-10 within the limits
of the PS-10 ratings.
Switch
Connect to
receiver
,I&E,I0Obattery
6^6"ATTERYRATING/UTPUT6)NPUT-.&UTABA#ORPWILLNOTBERESPONSIBLEFORDAMAGESETCCAUSEDBYCOMBINATIONWITHOTHERTHAN&UTABA#ORPPRODUCTSFUTABA CORPORATION oak kandakajicho 8F 3-4 Kandakajicho, Chiyoda-ku, Tokyo 101-0045, Japan
TEL: +81-3-4316-4820, FAX: +81-3-4316-4823
©FUTABA CORPORATION 2012, 2 (2)
Before using your new PS-10, please read this manual thoroughly and use it
properly and safely. After reading this manual, store it in a safe place.
7HENINSTALLINGTHE03TOTHEFUSELAGEUSETHEMOUNTINGmANGEANDTHESPACERIFNECESSARY5SETHESPACERAFTERCUTTINGOUTITFROM03USINGNIPPERSETCMounting flange
Spacer
Spacer
PS-10
Cooling effect:
The aluminum case is used for a face plate so that it can radiate the
internal heat efficiently. Mount PS-10 so that the aluminum case is exposed.
If PS-10 is mounted to the fuselage in the state where the aluminum case
side is turned down and wrapped in sponge etc., it will cause a loss of
cooling effect and the specified performances will not be obtained.
*It uses cutting
*It uses cutting
