Gamber Johnson 7160-1252 Series User manual

Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
Rev. B
INST-877
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
This instruction sheet is for the Getac UX10 TABLET docking station only. For instructions
on features, set-up, and operation of the computer, please refer to the manual provided by
Getac with the computer.
This docking station is designed to be used with a variety of Gamber-Johnson mounting
systems. Installation instructions for other Gamber-Johnson products are provided with each
individual product.
1 / 7
INSTALLATION INSTRUCTIONS
Product Revision Form
Printing Spec: PS-001
7160-1252
GETAC UX10 TABLET DOCKING STATION
If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868
This instruction sheet is for the following products:
Item No. 7160-1252-00 No RF (External Power Supply sold separately)
Item No. 7160-1252-03 Tri RF (External Power Supply sold separately)
Getac recommends using the following Power Adapters to power the docking station. They
can be ordered from Gamber-Johnson seperately.
17057 - Auto (12-32 Vdc input) - Available with the docking station as KIT 7170-0696
16079 - Isolated (12-32 Vdc input)
16078 - Isolated (20-60 Vdc input)
16513 - Isolated (72-110 Vdc input)

IMPORTANT SAFETY INFORMATION FOR INSTALLERS
Safety is dependent on the proper installation and servicing of this docking station. It is
important to read and follow all instructions before installing this product.
To properly install a Gamber-Johnson docking station you must have a good understanding of
automotive electrical procedures and systems, along with proficiency in the installation and
service of aftermarket vehicle equipment.
There are no adjustments required at any time of the electrical components within the docking
station. Opening the docking station will void the product warranty.
During Installation:
DO NOT connect this docking station to the vehicle battery until:
All other electrical connections are made 1.
Mounting of all components is complete 2.
Verification that no shorts exist in the entire system 3.
DO NOT install equipment or route wires or cords in the deployment path of any air bag.
When drilling into the vehicle, DO make sure that both sides of the surface are clear of
anything that could be damaged.
CAUTION: If wiring is shorted to the frame, high current conductors can cause hazardous
sparks resulting in electrical fires or flying molten metal.
After installation:
Test the docking station to ensure that it is working properly.
File these instructions in a safe place and refer to them when performing maintenance or re-
installing.
WARNING : Failure to follow all safety precautions and instructions may result in property
damage, serious injury, or death.
PRE-INSTALLATION RECOMMENDATIONS
Conduct a "Bench Test"
Gamber-Johnson strongly advises a "bench test" be conducted to verify all electronic and
software issues are resolved prior to installation:
Make sure the computer is operational by itself. 1.
Insert computer into the docking station and verify that the computer is 2.
operating in the dock.
Interconnect entire assembly and verify start-up of all components, including 3.
other equipment (printers, modems, scanners, etc.)
Gamber-Johnson recommends positioning of all mounts and equipment in the vehicle
prior to the actual install to verify that mounting locations are safe and practical.
2 / 7

FEATURE IDENTIFICATION
Port Identification
(Ports, see page 4)
Part#/Serial# Label
VESA 75mm Hole Pattern
1/4-20 x 0.500" hardware provided
External Antenna - SMA
(WiFi, GPS, CELL)
(Optional)
3 / 7
Lower Walls
Guide Pins
External Antenna - Tri RF
(Optional)
Upper Walls
Provides docking guidance
and connector protection,
prevents mis-docking
Docking Connector
(2) USB 2.0
(Fast Charging)
1500 mA
Barrel Key Lock
Slam Latch
Release Button

PORT IDENTIFICATION
4 / 7
Serial
Power Input: 19 Vdc
1.) Cable Tie Slots
(Port Specific)
Power
Ethernet
USB (2)
USB (2)
CABLE MANAGMENT FEATURES AND PROPER INSTALLATION
2.) Cable Tie Slots (2)
(Extra)
1.) Use Zip ties (provided) to secure each port cable to the specific strain relief feature on the dock
2.) Use Zip ties (provided) to secure bundled cables for improved routing - OPTIONAL
Cables route past mounting equipment
USB3.0
900 mA
USB3.0
(Fast Charging)
1500 mA
Ethernet
(RJ45)

DOCKING AND UNDOCKING THE TABLET
OPERATION - DOCKING
1. Insert the front of the tablet
into the front guide pines of the
dock. The walls on the dock will
guide the tablet into place.
2. Rotate the back of the tablet
and push down, overcoming the
resistance until an audible click is
heard.
3. Optional - With the dock in the
"Latched" position, turn the lock
to the "LOCKED" position (CW).
This will lock the tablet in the
dock, and secure the tablet if the
screen is closed and latched.
5 /7
Insert Bottom First
Rotate Tablet into the dock
"Latched Position
Alternate Hand Position
Insert Bottom First
Rotate Tablet into the dock
"Latched Position

DOCKING AND UNDOCKING THE TABLET
OPERATION - UNDOCKING
1. Turn the lock to the
"UNLOCKED" position (CCW).
2. With your thumb press up on
the latch mechanism.
3. Remove the tablet by pulling it
away from the dock. This can be
done with the same hand.
6 / 7
Press up on the latch Pull tablet
away
"Locked" Position "Unlocked" Position

Gamber-Johnson LLC, 3001 Borham Ave.,
Stevens Point, WI, 54481, USA, 715-344-3482
Regulatory Certification Information
Regulatory Model #: 7160-1252
GJ Model #'s & Description:
7160-1252-00 Dock-Getac UX10 Laptop-No RF
7160-1252-03 Dock-Getac UX10 Laptop-Tri RF
Certifications:
EN 55032: 2012/AC: 2013 Class B •
EN 50498: 2010 •
E-mark •
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions. (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
7/7