Game ready Med4 Elite User manual

POWERING UP
CONNECTING
WRAPS
IMPORTANT: Read complete indications,
contraindications, cautions, and warnings in
User Manual before using this product

This Quick Reference is for use after the
Med4 Elite has been properly set-up in the
clinical environment and is completely filled
with distilled water.
QUICK REFERENCE
After you switch the power on, press the
amber On/Off button. The Med4 Elite
operating system takes up to
60 seconds to load.
ON/OFF
Connect the desired Wrap to the
connector Hose. The Hoses are marked
with Patient Icons.
CONNECT WRAP
NOTE: Always return the Hose to the correct
Hose holster and wrap the Hose around the
Hose hanger when not in use.
1
Click connector
into place
Disconnect Button
© 2019 CoolSystems, Inc. All rights reserved. Med4 Elite Quick Reference PN 704589 Rev F

SELECTING
ATHERAPY
COLD
HEAT
COMPRESSION-ONLY
RAPID CONTRAST
IMPORTANT: Read complete indications,
contraindications, cautions, and warnings in
User Manual before using this product
FOUR THERAPY OPTIONS

QUICK REFERENCE
After properly connecting the Wrap, select the Patient
number that corresponds with the number on the
Connector Hose.
SELECT PATIENT
The Select Therapy screen appears with four active
therapy icons. Choose the desired therapy type to
begin setting it up.
SELECT THERAPY
Cold
Therapy Heat Therapy Compression- Only
Therapy
Rapid
Contrast
Therapy
1
2
© 2019 CoolSystems, Inc. All rights reserved. Med4 Elite Quick Reference PN 704589 Rev F
FOUR THERAPY OPTIONS

STARTING
ATHERAPY
IMPORTANT: Read complete indications,
contraindications, cautions, and warnings in
User Manual before using this product

QUICK REFERENCE
After selecting a therapy type,
choose therapy settings:
TIME
SETTINGS
COMPRESSION
LEVELS
Use the decrease and increase buttons to
adjust the various settings including
temperature, time, and compression levels.
COLD RESERVOIR
TEMPERATURE
SETTINGS
TEMPERATURE
SCALE
SWITCH
PATIENT
Press the green Start Button
when you’re ready to begin
the therapy session.
Once a therapy has started, you may Pause
and/or Stop at any time.
HEAT RESERVOIR
TEMPERATURE
SETTINGS
3
4
THERAPY SETTINGS
START THERAPY
© 2019 CoolSystems, Inc. All rights reserved. Med4 Elite Quick Reference PN 704589 Rev F
SNOOZE SETTINGS
(COLD THERAPY ONLY)
The system's master Snooze feature
is disabled by default. Enable it in
System Settings.

PAUSING
THERAPY
CHANGING,
OR STOPPING
IMPORTANT: Read complete indications,
contraindications, cautions, and warnings in
User Manual before using this product

PAUSING
THERAPY SETTINGS
QUICK REFERENCE
You may pause a therapy at any time. To resume the paused therapy
without any adjustments, press the Start button.
CHANGING
THERAPY SETTINGS
You may change therapy
session settings only while
treatment is paused.
STOPPING
A THERAPY
You may stop a
therapy at any
time. To stop,
press the Stop button. The
therapy session stops and
the Select Therapy screen
appears. The therapy settings cannot be adjusted. A new therapy
session can then be started with new settings.
2. Press the Start
button to resume
© 2019 CoolSystems, Inc. All rights reserved. Med4 Elite Quick Reference PN 704589 Rev F
1. Press the
Pause button
2. Press the Adjust
Therapy Settings
icon and adjust
settings as desired
1. Press the
Pause button
3. Press the Start button to resume
with new settings

TWO PATIENT
THERAPY
IMPORTANT: Read complete indications,
contraindications, cautions, and warnings in
User Manual before using this product

1. Connect the unused Hose
to the second patient
2. Select Patient 1 or Patient
2 on the Select Patient
screen to match the Hose
selected
3. Set up the second patient
therapy and Press the Start
button to begin therapy
1. Pause treatment on the first patient, and adjust the temperature
(This new temperature will be the same for both patients.)
2. Resume therapy for the first patient by pressing the Start button
3. Now set up the second patient and Press the Start button to
begin therapy
QUICK REFERENCE
For two patient therapy sessions, the heat and cold
reservoirs are shared between patients. Therefore, the
temperatures will be the same for both patients.
When setting up a
therapy for the second
patient that uses the
same reservoir as the
first patient, the therapy
temperature selection
(+ or -) buttons will be inactive. The reservoir temperature
will remain at the temperature set for the first patient. If a
different temperature is desired, all therapies must first be
paused in order to adjust the reservoir temperature.
TWO PATIENTS /
SAME THERAPY TYPE
TO ADJUST THE RESERVOIR TEMPERATURE:
TWO PATIENTS /
DIFFERENT THERAPY TYPE
© 2019 CoolSystems, Inc. All rights reserved. Med4 Elite Quick Reference PN 704589 Rev F