Gardeners 8610909 User manual

1-800-876-5520 • gardeners.com
[e-mail]
8% of our profits go back to our communities.
Learn more at gardeners.com/FoRCE-FoR-GoOD
Parts List Tools Needed
() "H OR () "H BOARDS Phillips screwdriver
() CORNERS Screw gun or drill with # Phillips bit
() PLATFORM SUPPORTS Rubber mallet or hammer
() FLAT STOCK Tape measure
() ASSEMBLED ' PANELS
() CORNER CAPS
() PHILLIPS SCREWS
FLOOR PLANKS
FABRIC LINER
Assembly
Important: When inserting the BOARDS and PANELS into the CORNERS,
make sure they are fully seated. Any gaps between the wood and the
CORNERS will prevent proper alignment with screw holes.
1. Identify and organize all parts on a clean, level surface. NOTE: The BOARDS
may have both a rough and smooth side. The FLOOR PLANKS may be different widths.
2. Place two "H OR FOUR "H BOARDS on a flat surface,
with the smoothest sides facing down. Align the ends of
the BOARDS and press them tightly together. NOTE: We
recommend using a clamp or having another person hold
them firmly together.
3. Slide a CORNER onto the ends of the BOARDS, positioning it so
the holes in the CORNER match Fig. 1. NOTE: The top BOARD
should sit ⅛" above the top of the CORNER. Make sure the
BOARDS are tight together and are fully seated in the CORNER,
then use your screw gun to insert SCREWS through the holes,
skipping the nd hole from the bottom. Repeat to attach
another CORNER onto the other side of the BOARDS.
4. Using the ASSEMBLED ' PANELS as a reference, line up the holes in the ends of
the PLATFORM SUPPORT with the open holes in the CORNERS (Figs. 1 & 2). Insert
a SCREW into both sets of holes.
5. Again using Fig. 1 and the ASSEMBLED ' PANELS as references, slide  FLAT
STOCK underneath the PLATFORM SUPPORT. Align with holes nd from the bottom
of the FLAT STOCK with the holes in the PLATFORM SUPPORT and make sure they
are straight. Secure the FLAT STOCK into place by inserting SCREWS through all
holes.
6. Repeat Steps – to assemble the other side panel.
S Rev /#
4' x 4' Elevated Planter Box
holes
PLATFORM
SUPPORT
FLAT STOCK
CORNER
Figure 1: SIDE PANEL
The top BOARD
should sit ⅛"
above the top
of the CORNER.
BOARDS
Figure 2
attached CROSS
SUPPORT
assembled 2'
END PANEL
BOARDS
CORNER
PLATFORM
SUPPORT
Assembly is easiest with two people.
Illustrations show assembly with 8"H
boards.

7. Use a rubber mallet to tap an ASSEMBLED ' PANEL into the open channel of a
CORNER, positioning it so the attached PLATFORM SUPPORT sits underneath the
PLATFORM SUPPORT on the side panel (Figs. 2 & 3). Make sure the top of the
ASSEMBLED ' PANEL sits ⅛" above the top of the CORNER and is fully seated inside,
then insert SCREWS into the holes in the CORNER and through the lined up holes
in the ends of the PLATFORM SUPPORTS. Repeat to attach the other ASSEMBLED '
PANEL.
8. Place the remaining side panel on a flat surface. Carefully lift the other attached
PANELS and guide the ends of the ASSEMBLED ' PANELS into the open channels of
the CORNERS on the side panel to form a box. Insert SCREWS through the holes in
both CORNERS. Once all panels are attached, stand the PLANTER BOX on its legs.
9. Set the FLOOR PLANKS on top of the SUPPORTS, arranging them so there are small
gaps between the planks. NOTE: The gaps allow water to drain. Place the FABRIC
LINER over the FLOOR PLANKS.
10. Insert a CORNER CAP into the top of each aluminum CORNER, using a rubber mallet if necessary. Your planter box assembly is
now complete!
This elevated planter box holds almost  quarts or  cubic feet of planting mix. Fill it with Potting Mix and, if you wish, some
organic matter, such as compost. We also recommend adding a slow-release fertilizer like our Organic All-Purpose Fertilizer (sold
separately). NOTE: Avoid using a heavy potting soil or placing rocks and broken pottery into the Planter Box. Now you’re ready to
plant!
For how-to articles on growing vegetables and flowers in containers and raised beds,
visit us at gardeners.com
Figure 3
SIDE PANEL
ASSEMBLED
4' PANEL
The attached PLATFORM SUPPORT
sits underneath the PLATFORM
SUPPORT on the 4' SIDE PANEL.
SCREW
PLATFORM
SUPPORT
PLEASE
RECYCLE