Gasmate EH431 User manual

03867 02/19
Model No. EH431
Important: Retain these instructions for future use
2000W Quartz heating element
Designed for indoor and outdoor undercover use
Ideal for use under Verandas, Alfresco areas and Garage
The perfect solution to extend alfresco entertaining in the
cooler months
Left/right oscillation
Easy installation
Remote control operation
Ultra slimline design with brushed aluminium body

32
WARNING - In order to avoid over heating, DO NOT COVER the heater.
SPECIFIC SAFETY INSTRUCTIONS
WARNING
This heater is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning the use of the heater by a person responsible
for their safety. Children should be supervised to ensure
that they do not play with the heater.
Do not use the heater in areas where there is a risk of
explosion or re from ammable gases. Ensure that
the heating area is kept clear of combustible materials.
Do not use the heater in damp areas, without suitable
ventilation. This heater is not designed for use within 1m
or above a water source. Do not place within one metre
(1m) of any water source. Do not place directly below or
above any power points or switches.
WARNING: Fire risk exists if this heater is covered by
or positioned close to curtains or other combustible
materials.
• This heater is intended for domestic/household use
only.
• Always ensure that this heater is installed as per the
requirements noted in Australian Standard AS/NZS
3000:2007.
• Always keep heater at least one metre (1m) from
combustible materials.
• DO NOT locate this heater directly below or above
the power supply socket or switch.
• DO NOT use this heater in either a bathroom
or ensuite.
• DO NOT use a 3rd party timer, or programmable
system with this heater.
• DO NOT clean the heater while the heater is on or
plugged into the mains power supply.
• DO NOT touch any part of the heater while on, hot
surfaces may burn.
• DO NOT use the heater as a dryer.
• DO NOT attempt to modify the heater, power cord,
power plug or the supplied accessories in any way.
• DO NOT expose the heater to rain, water, or use in
damp wet conditions.
• NEVER cover this heater.
• NEVER carry the heater by its power supply cord.
• NEVER use with the power cord coiled, bundled up
or tied up. Always extend fully before use.
• NEVER use the heater if any part of it is damaged.
• Ensure that the heater is disconnected from the mains
supply when installing, cleaning or moving.
• Ensure this heater is not left on when unattended.
• Ensure the heater is not used in areas where
ammable gases are present, e.g. paint, petrol etc.
• Always turn the heater OFF at the unit switch and
the power point switch when not in use for extended
periods of time.
• Always allow the heater to cool, about one (1) hour
after the heater has been turned o, before cleaning
the heater.
• Always ensure that the power cord is fully extended
and NOT in contact with any part of the heater.
• Always ensure that the heater is kept clean and free
from dust.
• Only use this heater when securely mounted to the
wall.
• Remove the remote control batteries when not using
the heater for long time.
• Choose the same specication battery when replacing
the remote control batteries, otherwise it may cause
remote control not work, therefore aecting the normal
use of the heater.
• The remote control function is line of sight and may
not operate is something or someone is in the way of
the signal.
• Replacing the batteries regularly is suggested to
ensure the normal use and operation of heater.
If the mains connection plug or power cord becomes
damaged it must be replaced with a complete assembly
that is identical to the original, and this must be replaced
by the manufacturer or an authorised service centre or
similar qualied persons in order to avoid a hazard.
This logo/symbol means DO NOT COVER.

32
Safety
Before attempting to operate this heater, the following
basic safety precautions should be taken to reduce
the risk of re, electric shock and personal injury. It
is important to read the instruction manual and to
understand its’ applications, limitations and potential
hazards associated with this heater.
This heater is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning the use of the heater by a
person responsible for their safety. Children should
be supervised to ensure that they do not play with the
heater.
This heater is not designed for use within 1m or above a
water source. It is important that you read, understand
and follow these instructions very carefully. They are
designed for the safety of yourself and others ensuring
a long and trouble free service life from your heater. This
electric heater complies with Australian and International
standards and safety requirements. Repairs should only
be carried out by qualied persons using original spare
parts. Failure to do so may result in considerable danger
to the operator.
SAFE OPERATION
Beware of Children and Pets
Children should not be allowed to touch or operate
heaters or touch extension cords, if used. All heaters
should be kept out of reach of children, preferably
stored or locked in a secure cabinet or room when not
in use.
Do not abuse or damage the power cord
Never yank or pull on the power cord to disconnect it
from the mains supply socket. Never carry your heater
by its’ power cord. Keep the power cord away from
heat, oil, solvents and sharp edges. Check the power
cord regularly for any damage and if the power cord
becomes damaged have it replaced by an authorised
service facility.
Extension Cords and Reels
This heater is NOT designed to run o an extension
cord. If you require an additional power point please
have one installed by a qualied electrician.
The use of extension cords may cause power voltage
loss which will result in damage to the motor this will
NOT be covered under warranty.
INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS
Installation
Always ensure you select the correct xing accessories
which suit the particular material you are attaching to, if
in doubt please discuss with your local retailer or local
hardware store. This heater is not designed for use
within 1m or above a water source. All installations must
meet the requirements of Australia Standard AS/NZS
3000:2007.
Ensure that the heater is not positioned directly above or
below a power point or switch.
This heater is not designed to be used with 3rd party
timer or programmable system.
WARNING: Fire risk exists if this heater is covered by
or positioned close to curtains or other combustible
materials.
NOTE: When using this heater outside ensure that it is
connected directly to an outdoor power point.
The electrical system of this heater must be connected
with an automatic 30mA circuit breaker and/or residual
current device (RCD). If uncertain have a qualied
electrician check your electrical system before
installation and/or use.
All electrical connections are made in a dry area.
Outdoor power points must be weatherproof and
installed by a qualied electrician.
Sitro Group Australia Pty Ltd is not responsible for
incorrectly chosen xing accessories or any damage
which may be caused by an incorrectly tted heater.

54
Heater EH431
Voltage 220-240V AC 50Hz
Input Wattage 2000W
Unit Weight 3.5Kg
IP Rating IP65
Oscillation Angle 60° ± 5°
Tilt Angle from Horizontal 30° ± 5°
Remote Control Batteries
(not supplied) 2 x AAA
Electrical Approval GMA-505003-EA
Heater specications can be found on the data label.
IMPORTANT
This product is tted with a sealed electrical connection
plug that is compatible with the heater, the mains supply
for Australia and meets the requirements of international
standards. This heater must be connected to a supply
voltage that is equal to that stated on the rating label.
If the mains connection plug or power cord becomes
damaged it must be replaced with a complete assembly
that is identical to the original, and this must be replaced
by the manufacturer or an authorised service centre
or similar qualied persons in order to avoid a hazard.
Always follow the Australian requirements for connection
to the mains supply. If in doubt always consult a
qualied electrician.
Technical Specification
ELECTRICAL DATA

54
NOTE: Remove any and all transit protection material.
If unsure about the type of xings you require to mount
your wall heater please discuss with your local hardware
store.
• Ensure the xing screws are at least suitable for 10kgs
each.
• If xing to a stud wall ensure all xing screws are into
timber.
• If no timber studs are available we would suggest
installing a timber batten to attach to.
• The bottom of the wall heater body should be 1.8m
above the oor.
• Do not position the wall heater directly above or
below a power point or switch.
• Do not position wall heater in front of a power point.
TO MOUNT THE WALL HEATER BRACKET
1. Take the wall bracket and select the position on the
wall
2. Mark the holes for the wall bracket and drill
3. Using 4 suitable screws (not supplied) attach the
wall bracket to the wall. Now assemble the wall
bracket to the heater.
ASSEMBLE THE WALL HEATER
1. Have the heater with the OSCILLATION BOX on top
and facing upwards.
2. Using the screws, washers and nuts assemble the
wall bracket to the heater/oscillation box.
It is suggested to have the bolts from the top and
the washers and nuts from the bottom.
3. Securely tighten the bolts and nuts.
4. Wall heater is now ready to mount to the wall using
your wall xings (not supplied).
5. Securely mount the wall heater to the wall.
WALL MOUNTING HEATER & ASSEMBLY