Gate Bure Standard EL 56-312T User manual

BureTM
PMS 322 C
Bure Standard EL 56-312T
Bure S EL 56-302T
Bure Low EL 56-321
Bure Low S EL 56-321-S
Walker
Instructions for use
digital

Adjusting
the handles
To adjust handles to
the desired position;
loosen screw, adjust
handle, tighten screw.
Dear User,
Congratulations on obtaining a Bure Walker! These
instructions provide important information on how
to use the walker and how to maintain it.
All of us here at GATE Rehab Development hope
you enjoy using your new product. If you have any
comments, questions or points of view, please
contact us on [phone].
Raising and lowering
the frame
Adjust the height with
the aid of the remote
control UP and
DOWN arrows.
Left and right adjustment of armrests
The armrests can be
adjusted sideways for
optimal support;
loosen screw, adjust
armrest, tighten screw.
Bruksanvisning Bure
Justering av handtag
Handtagen justeras till önskad position genom att:
Ratt lossas, justera in handtag
Ratt låses
Upp
Ned
Min
Max
Höjning/sänkning
av stativ (El)
Önskad höjd justeras med hjälp
av fjärrkontrollen
Pil <UPP> resp. Pil <NED>
Breddning av stativ
(endast Bure Double)
Önskad bredd (max/min) justeras
med hjälp av fjärrkontrollen:
Håll in Pil <vänster> = Minimal
breddning av benstativ.
Håll in Pil <höger>
= Maximal breddning av
benstativ.
Justering av armstödsplattor (Hö/Vä)
För optimalt stöd kan Armstödsplattor breddjusteras:
Ratt lossas, armstödsplattas läge justeras. Ratt låses
Låsning av hjul
Hjulen låses genom att fotbroms aktiveras.
Upplåsning av hjul
För att lossa bromsen – återställ.
1. Uttag för batterikontakt
2. Uttag för stickpropp
(OBS! För att IP-klassning ska gälla så ska
stickpropp ALLTID vara ansluten till styrbox)
3. Uttag för fjärrkontroll
4. Uttag för ställdon - höj/sänk
5. Uttag för ställdon - breddning (Endast Bure Double)
OBS! Var noga med att kontakter ansluts till rätt uttag eftersom detta annars
kan skada ställdon.
Laddning av batteri ska ske då gåbordet inte används.
(Batteriet kan aldrig överladdas.) Laddning görs genom
att stickpropp ansluts till eluttag.
Innan första användningen så bör batteriet
laddas 24 timmar.
Kopplingsschema Styrbox
(Bure El/Bure Double/Bure Extra)
Laddning av batteri
(Bure El/Bure Double/Bure Extra)
2
3
4
1
5
Bruksanvisning Bure
Justering av handtag
Handtagen justeras till önskad position genom att:
Ratt lossas, justera in handtag
Ratt låses
Upp
Ned
Min
Max
Höjning/sänkning
av stativ (El)
Önskad höjd justeras med hjälp
av fjärrkontrollen
Pil <UPP> resp. Pil <NED>
Breddning av stativ
(endast Bure Double)
Önskad bredd (max/min) justeras
med hjälp av fjärrkontrollen:
Håll in Pil <vänster> = Minimal
breddning av benstativ.
Håll in Pil <höger>
= Maximal breddning av
benstativ.
Justering av armstödsplattor (Hö/Vä)
För optimalt stöd kan Armstödsplattor breddjusteras:
Ratt lossas, armstödsplattas läge justeras. Ratt låses
Låsning av hjul
Hjulen låses genom att fotbroms aktiveras.
Upplåsning av hjul
För att lossa bromsen – återställ.
1. Uttag för batterikontakt
2. Uttag för stickpropp
(OBS! För att IP-klassning ska gälla så ska
stickpropp ALLTID vara ansluten till styrbox)
3. Uttag för fjärrkontroll
4. Uttag för ställdon - höj/sänk
5. Uttag för ställdon - breddning (Endast Bure Double)
OBS! Var noga med att kontakter ansluts till rätt uttag eftersom detta annars
kan skada ställdon.
Laddning av batteri ska ske då gåbordet inte används.
(Batteriet kan aldrig överladdas.) Laddning görs genom
att stickpropp ansluts till eluttag.
Innan första användningen så bör batteriet
laddas 24 timmar.
Kopplingsschema Styrbox
(Bure El/Bure Double/Bure Extra)
Laddning av batteri
(Bure El/Bure Double/Bure Extra)
2
3
4
1
5

Locking castors
Depress the foot brake
to set it and lock the castor.
Unlocking castors
Press down on the protruding
part of the brake to release it.
Control box wiring
Remove the control box cover to
make the connections as described
below. Use a screwdriver or similar;
refer to
the special labels on the control box.
1. Socket for the raise/lower
actuator.
NOTE! Make sure that plugs are
connected to the correct sock-
ets otherwise the actuators can
be damaged.
2. Remote control socket.
3. Battery terminal socket.
4. Plug socket. NOTE! The plug
must ALWAYS be connected to
the control box for IP protection
to be valid.
2
3
4
1

Battery charging
• Connect plug to 230V wall socket. Charging begins auto-
matically and the battery LED flashes green.
• Make sure the battery is fully charged before using for the
first time. It takes around
25 h to fully charge the battery.
• We recommend that the battery plug be removed from the
control box if the product will be out of use for an exten-
ded period (more than one week) or if the battery is swit-
ched off by means of the ON/OFF switch. This eliminates
the risk of disabling the battery as the control box always
uses a small quantity of electricity even when the walker is
not in use.
LEDs on control box and battery
• Control box – green light when power is available from bat-
tery/mains socket.
• Battery:
• The LED flashes green during
charging.
• ON/OFF: To use the product,
press ON.
• The green lamp will begin to flash.
• Use the OFF button (hold down for 5 s) to switch off the
battery if the product will not be used for an extended
period.
• The LED will shows a constant green light when the battery
is fully charged.
• When the battery is in normal state/in operation, the LED
• flashes green at REGULAR intervals, namely 0.5 s ON, 4 s
OFF.
• When the battery requires charging (remaining charge
<25%) the LED will flash
• orange/red at REGULAR intervals, namely 0.5 s ON, 4 s
OFF.
NOTE! The battery has an in-built device that automatically
switches it off when remaining charge is <20%. The LED is
then extinguished. The battery must now be fully charged
before the electronics can be used again.

Maintenance
Recommended at least once per year.
Check that Action
General
The walker feels firm/free from play.
The walker does not rattle during
manoeuvres.
The walker is level and all of its castors
are in contact with the floor.
The walker is not dirty.
Armrests
Armrests are intact and clean.
Armrest widening is functional.
Handle
Grips are not damaged/dirty.
Handle adjustment is functional.
Battery
Check that the charging cable is
connected to the control box.
Check that the remote control is
connected to the control box.
Check that connections are made
according to the wiring diagram.
Check that the battery, actuators and
control box are not loose.
Height adjustment
Raising and lowering are functional.
The walker feels stable at maximum
settings.
There is no play between the vertical
frame and bottom frame.
Height adjustment clamps lock.
The electric actuator fitting must be free
from play.
Height adjustment via remote control is
functional. The electric actuator must run
smoothly at a constant speed.
Frame parts
There is no mechanical damage.
There are no scratches.
End plugs/lower frame fitted.
Castors/brakes
Castors roll easily/tread not damaged.
The castors are firmly fastened to the
lower frame.
Castor brakes functional on all castors.
Handbrake functional.
Clean with lukewarm soap solution or
alcohol-based cleaning agent
(no petroleum products).
Clean; replace if damaged.
Fit lock screws/plates as required.
Clean with lukewarm soap solution
(no petroleum products).
Replace handle grips.
Fit lock screws/plates as required.
Fit new charging cable; this must always
be connected to the control box (IP65
protection).
Connect or fit new remote control as
required.
Refer to the wiring diagram in the
Technical manual.
Tighten; replace with new fasteners as
required.
Fit new guide sleeves (in frame) or end
plugs (in chrome tubes) as required.
Tighten all lock bolts.
Replace clamps.
Tighten the attachment fitting concerned;
replace bolts/lock nuts
as necessary.
Check that the battery/remote control/
actuator are connected in accordance
with the wiring diagram. Charge the
battery. Contact customer services.
If damage is present, contact GATE’s
customer services.
Touch up as necessary.
Fit new end plugs.
Clean or replace castors.
NOTE! Castors are always fixed to the
lower frame with thread locker or lock
nuts. Do not dismantle the castors;
replace the whole castor assembly
instead.
Tighten the castor bolt and fit locking nut
or use thread locker (depends on model).
Replace castor assembly.
Adjust the brake or fit new castors.

Standard EL
Part No.
56-312T
Width
78 cm
Max user weight
150 kg
Length
80 cm
Height
91–131 cm
Armrest/internal dimension
25–50 cm
Bure Low EL
Part No.
56-321
Width
78 cm
Max user weight
150 kg
Length
80 cm
Height
75-100 c m
Armrest/internal dimension
25–50 cm
S EL
Part No.
56-302T
Width
66 cm
Max user weight
150 kg
Length
79 cm
Height
91–131 cm
Armrest/internal dimension
30–45 cm
Bure Low S EL
Part No.
56-321-S
Width
66 cm
Max user weight
150 kg
Length
79 cm
Height
75-100 c m
Armrest/internal dimension
30–45 cm
General maintenance advice
• Clean the walker and its armrests clean as necessary;
Wipe using a soap solution/surface disinfectant.
• The product may be cleaned in a tunnel washer or similar as
electrical systems have IP65 protection. However, the product
is not corrosion proof which means washing by machine may
reduce its lifetime.
• Replace damaged parts immediately; must be done by
experienced personnel.
• The product is only intended for indoor use.
CE marked according to MDD 93/42/EEC.
Tested and approved according to EN-11199-3/2005
2016-03-31, 4
PMS 322 C
DIN PARTNER I VÅRDEN
Would you like to know more?
Contact us at:
Tel: [phone]
Gate Rehab Development AB
Industrigatan 2 | SE-330 21 Reftele
[email protected] | www.gaterd.com
Technical specifications
Dimensions apply to walkers with 125 mm castors.