Gaymar TP702 User manual

T/PUMP®
TP702 Localized Temperature
Therapy System
Operator's Manual [EN]
P/N 101516000 Rev A 7/11www.gaymar.com
0086

OPERATOR'S MANUAL
TP702 T/PUMP
T/PUMP, T/PAD, Mul•T•Pad, Clik-Tite, and Gaymar are registered trademarks of
Gaymar Industries, Inc. U. S. PATENT 4,068,870
Incidin Extra is a registered trademark of Ecolab Healthcare Division.
© 2009. Gaymar Industries, Inc. All rights reserved.
BEFORE YOU BEGIN . . .
Read and understand this T/PUMP OPERATOR'S
MANUAL and all SAFETY PRECAUTIONS
(see page 1) prior to using the T/Pump.
Only qualied medical service personnel should repair or perform
function tests on the T/Pump. Contact your dealer or Gaymar's
Technical Service Department for assistance:
Telephone: [phone]
RECEIVING INSPECTION
Check the shipping carton for damage immediately upon receipt. If
package damage is discovered, the device should be unpacked with the
carrier's agent present. Any claims for shortage or damage must be led
with the delivering carrier by the purchaser. Do not return pumps that
were damaged in shipment to Gaymar without contacting our Technical
Service Department for advice (see phone numbers below). If damaged
goods are returned to Gaymar without notifying the carrier, Gaymar will
assume the repairs will be made at the customer's expense.
TO RETURN PUMPS TO FACTORY FOR REPAIR OR
EXCHANGE
Merchandise returned to Gaymar must be accompanied by a Return
Goods Number (RG#), issued by Gaymar, authorizing goods to
be returned. Contact your local dealer or Gaymar's International
Department at:
International: [phone]
Fax: [phone]
Provide the model, serial number, and detailed nature of the problem.
You will be given a Return Goods Number (RG#).
The serial number can be found on the bottom of the T/Pump.
CONTENTS
SAFETY PRECAUTIONS.........................1
INTRODUCTION.....................................2
INDICATIONS FOR USE ........................4
CLINICAL CONTRAINDICATIONS...4
PUMP FEATURES.......................................5
KEYPAD FEATURES TP702 .....................6
CLIK-TITE® CONNECTORS..................7
START-UP PROCEDURE..........................8
SHUTDOWN PROCEDURE..................8
THERAPY CYCLES,
PROFESSIONAL ONLY..........................9
TROUBLESHOOTING.............................10
STORAGE / CLEANING....................... 13
PREVENTIVE MAINTENANCE/
SERVICE....................................................15
SPECIFICATIONS................................... 16
WARRANTIES......................................... 17
SYMBOLS USED WITHIN THIS
MANUAL AND ON THE PRODUCT
Warm Water Fill Line
Cold Water Fill Line
Attention, consult Operator's
Manual.
Water Levels
Water Flow
Dangerous Voltage
Type BF Applied Part
Do not penetrate with sharp
object.
Length of cycle time
Continuous
Year of manufacture
BEFORE YOU BEGIN . . .
The date of manufacture of the T/Pump is encoded to the serial
number. To determine the date of manufacter, the serial number
can be broken down as follows.
A 0 1 0 0 1
Month Year Decade These numbers are
not signicant to the
date of manufacture
A January
BFebruary
CMarch
DApril
EMay
FJune
GJuly
HAugust
ISeptember
JOctober
KNovember
LDecember

OPERATOR'S MANUAL
TP702 T/PUMP
1www.gaymar.com
DANGER
• Riskofexplosion.Do not use in the presence of ammable
anesthetics.
• Riskofelectricshock.Disconnect power before servicing the
T/Pump.
• Do not attach the power cord to any moving parts of the bed
frame or any location that may be a pinch point or cause power
cord damage. If routed improperly, the power cord may become
pinched and could cause electrical shock.
SAFETY PRECAUTIONS
SAFETY
PRECAUTIONS
WARNING
CAUTION
• Federal law restricts this device to sale by or on the order of a
physician.
• Do not cover the control unit with blankets, pillows or other
insulating materials. Air ow is required to maintain system
performance.
WARNING
WARNING
• This device pumps temperature controlled water through a
pad. Set the pad temperature only as directed by and under the
guidance of the prescriber.
• Check the skin integrity of the body surface to which therapy is
applied. Evaluate patient response to temperature application.
• Check patient's skin for adverse reactions every 30 minutes or as
directed by the prescriber.
• Failure to adhere to these warnings could result in patient injury.
• The following Groups/Conditions require additional surveillance:
Group/Condition at risk Potential Injury
Pediatric patients: The portion of an
infant’s skin surface in contact with
a pad, in relationship to their body
mass, can potentially affect their body
temperature.
Hyperthermia/
Hypothermia
Patients with impaired circulation Ischemia
Areas of application under pressure Ischemia
• Only qualied medical service personnel should repair the
T/Pump. Improperrepairmayresultindeathorseriousinjury,
equipmentdamage,ormalfunction.
• Use T/Pump TP702 controls with Mul•T•Pads. For catalog numbers
and descriptions, see page 3.
• Do not place additional heat sources between the patient and pad.
Skin damage may result.

OPERATOR'S MANUAL
TP702 T/PUMP
2www.gaymar.com
INTRODUCTION
Heat therapy is effective in the dilation of blood vessels, thereby increasing
the blood ow to the heated area. Heat therapy has a variety of uses, the
most common being treatment of aches and pains in joints and muscles.
Cooling therapy assists in vasoconstriction, decreasing blood ow and
decreasing the metabolism in the affected area. Cooling therapy is applied
in the acute phase of injury minimizing blood loss, inammation of the
tissue, and can be effective in pain management.
The Gaymar T/Pump® Localized Temperature Therapy System provides
therapy by warming or cooling the enclosed water, and circulating it
through the Gaymar Mul•T•Pad. The pad is connected to the Gaymar
T/Pump with easy-to-use Clik-Tite® connectors.
The Mul•T•Pad provides the interface for delivering the temperature
therapy. The unique button design allows water to ow and provides
trouble-free operation when the pad is folded to form a customized t.
This reduces the number of pads your facility must keep in inventory.
The pads are applied to the part of the body requiring therapy, and the
circulating water maintains the pad at the setpoint temperature. The
setpoint temperature can be locked to prevent tampering.
INTRODUCTION
Figure 1A: Localized Temperature
Therapy System with Single Pad
with the TP702.
Figure 1B: Localized
Temperature Therapy
System with Multiple Pads.
The Mul•T•Pads can be interconnected using Clik-Tite® connectors to
provide therapy to more than one body site at a time.
Connecting the Pads

OPERATOR'S MANUAL
TP702 T/PUMP
3www.gaymar.com
Catalog Descriptions Catalog # Product Name
TP702 Professional Control Unit
TP12E Mul•T•Pad: 13"w x 18"l (33cm x 45cm)
Nonwoven fabric on one side, pliable polymer on the
other side. 20 per carton
TP22E Mul•T•Pad: 15"w x 22"l (38cm x 55cm)
Nonwoven fabric on one side, pliable polymer on the
other side. 20 per carton
TP22G Mul•T•Pad: 15"w x 22"l (38cm x 55cm)
Heavy Polymer, Reuseable. 10 per carton
TP26E Mul•T•Pad: 18"w x 26"l (45cm x 66cm)
Nonwoven fabric on one side, pliable polymer on the
other side. 10 per carton
INTRODUCTION
To order any of these products contact your dealer or Gaymar's
International Department at:
International: [phone]
Fax: [phone]
Or, visit our website at www.gaymar.com

OPERATOR'S MANUAL
TP702 T/PUMP
4www.gaymar.com
INDICATIONS AND CONTRAINDICATIONS
INDICATIONS FOR USE Localized temperature therapy is recommended in treating the following
applications:
Orthopedic Conditions such as:
acute injuries, chronic pain, lower back pain, muscle spasm and
strains
Skin Trauma such as:
abscesses, boils, bruises, burns and contusions
Cold Indications
muscle spasm
contusions
tendonitis
pain management
Other conditions such as:
chronic arthritis, neuritis, phlebitis, tendonitis and I.V. inltration,
infection and localized pain.
Other applications only as prescribed.
CLINICAL
CONTRAINDICATIONS
Heating contraindications are:
• Application to a body surface with compromised blood ow
(Ischemia, area under pressure, arterial insufciency).
• Application to a patient with an increased tendency to bleeding
(aggravates potential for hemorrhage).
• Application to a body surface with possibility of malignancy (tissue
metabolism is increased and therefore, the growth potential of the
malignant tissues).
• Treatment of hematoma within rst 24-48 hours (potential for
re-bleeding and hemorrhage).
• Recent sprain or fracture (acute inammatory response).
• In combination with topical solutions whose toxicity may be
affected by the application of heat.
• In combination with other heat sources.
Cooling contraindications are:
• Application to a body surface with compromised blood ow or
hypersensitivity to cold. (Ischemia, Reynauds Syndrome).
OK for Use With:
• Non-acute traumatized tissue.
• Impaired mental status.
• Insensate body surface.
• O2 therapy. However, if oxygen tent is in use, do not use pump inside
tent.

OPERATOR'S MANUAL
TP702 T/PUMP
5www.gaymar.com
PUMP FEATURES Easy to Use
Keypad
See KEYPAD FEATURES on page 6.
Attached hose 10 ft (305 cm) dual hose. Connectors allow pads to be
connected to the pump (Figures 1A and 1B, page 2).
Flow indicator Indicates no ow. Turns off heater if pump is tipped.
Warm/Cool
Delivery
Four temperature setpoints on the TP702.
Therapy Cycles Choose from 20-minute, 30-minute, or Continuous
cycles.
On/Standby
Button
Indicates power is supplied to the unit.
Over Temp Safety
Thermostat
Limit thermostat shuts off heater if the high temperature
limit is exceeded.
Self Check Automatic system check at startup.
Hose/cord
Management
Convenient and easy storage areas for hose and cord.
Comfortable
Handle Design
Designed for a more comfortable grip when moving the
pump.
Dual Micro
Processor
Two electronic circuits, one over temperature sensing
circuit.
Tethered Easy-
Open Cap
Prevents misplacing the cap. Only 1/4 of a turn is needed
to remove or secure the cap.
Handle Vents The vents in the handle allow air ow to keep the
motor and heater inside the unit cool.
FEATURES
Figure 2: T/Pump Features
Easy to Use Keypad
Hose Connections
Flow Indicator
Temperature Setpoints for
warm or cool delivery
On/Standby Button
Tethered Easy-Open Cap
Hose storage
Cord storage
Comfortable Handle
Therapy Time Cycles)
Vents in Handle

OPERATOR'S MANUAL
TP702 T/PUMP
6www.gaymar.com
Indicator/
Warning
Light
See the Troubleshooting section on page 11.
Water Flow
Check hoses or clamps for kinks or occlusions.
Water Level
Check water level.
Setpoints Press the button at the bottom of the setpoint indicator
to toggle through the four setpoints. Temperatures are
identied in °C.
Setpoint
Lock
Prevents tampering.
Press and hold for 2 seconds to lock or unlock the
setpoint.
Therapy
Cycles Continuous cycle,
30-minute cycle
20-minute cycle.
Green indicates the unit is on.
Yellow indicates power is supplied to the unit but the
unit is not on.
KEYPAD FEATURES
TP702
Figure 3: TP702 Keypad
FEATURES

OPERATOR'S MANUAL
TP702 T/PUMP
7www.gaymar.com
OPERATING INSTRUCTIONS
Figure 4: Clik-Tite® Connectors
The TP702 T/Pump is supplied with Clik-Tite® connectors.
To connect and disconnect Clik-Tite® connectors from hose to pad:
1. Insert male ttings into female ttings with a twisting motion
(Figures 4A and 4B).
2. When ttings are fully inserted, snap locking ring into place
(Figures 4C and 4D).
3. To disconnect, reverse the procedure.
4. To open or close the hose pinch clamps:
• Open the clamp by pushing the serrated end (Figure 5B).
• Close the clamp by pressing the clamp together (Figure 5C).
Note: Refer to Figure 1B on page 2
when connecting multiple pads.
CLIK-TITE®CONNECTORS
5A 5B
5C 5D
4A 4B
4C 4D
5B 5C

OPERATOR'S MANUAL
TP702 T/PUMP
8www.gaymar.com
OPERATING INSTRUCTIONS
SHUTDOWN PROCEDURE
START-UP PROCEDURE
1. Before lling the pump, attach a pad to the connector hose.
Make sure that there are no kinks in the hose or pad. Open the
hose clamps.
2. Open the ll cap on top of the pump.
3. To ll for cooling:
a. Fill with cold water to the Cooling water line.
b. Fill with ice to the full capacity of the reservoir.
4. To ll for heating, ll with room temperature
water to the Heating water line.
5. Plug the T/Pump into a properly grounded Hospital Grade
receptacle.
6. Press the On/Standby button.
The light next to the selected temperature begins to ash.
7. Use the keypad to set the temperature as directed by the
prescriber. After setting the temperature, press and hold the lock
Temperature Setpoint button for 2 seconds to lock the setpoint.
Note: If you toggle past the desired setpoint, keep toggling
to start at the beginning of the setpoint column.
The selected water temperature will be reached in
approximately 15 minutes and the light next to the selected
temperature becomes steady.
8. Check the water level. If it drops below the operating level, add
water.
9. Apply the Mul•T•Pad to the patient as prescribed. Follow the
Mul•T•Pad instructions.
10. Position the pump at or above the level of the pad.
Note: If the pump is placed below the pad(s), water will
drain into the pump when it is shut off. If the pump has been
overlled or if multiple pads are connected, excess water
can leak.
11. When using for cooling, the ice will eventually melt and the
setpoint will start ashing. Press on/standby button so the
standby light is lit. Unplug pump from power receptacle. Open
ll cap and invert pump over sink to drain water. Refer back to
step #3 and follow through procedure.
1. Press the On/Standby button so that the Standby light is lit.
2. Unplug the T/Pump.
3. Close all hose clamps.
4. Disconnect pad(s) from pump.
To prevent water spillage, always disconnect pad from pump with
connectors raised above the level of the pad and pump.
5. Coil the hose, and attach the Clik-Tite® connectors together on
the hose (See Figure 4, Page 7), where applicable.
6. Secure the hose to the T/Pump using the tube set strap.
7. Wrap the power cord around the unit.
•
• Pumpmustbelledwithwaterpriortooperation.

OPERATOR'S MANUAL
TP702 T/PUMP
9www.gaymar.com
THERAPY CYCLES
OPERATING INSTRUCTIONS
1. Turn the unit on, set the temperature setpoint. The unit will
start to heat up. Select warming period for 20 (or 30) minute
cycle, LED should be solid, and the selected temperature LED is
ashing.
2. Once the T/Pump reaches the desired temperature, the Warming
LED (Red) ashes with a short audible beep. This is to let the
operator/user know the unit is at temperature and the timed
therapy is starting.
3. Once the 20 (or 30) minute period is up, the heater and pump
shuts off. This stops any ow to the pad. The Setpoint and
Therapy time LED's will be blinking during the off Time period.
4. Once the Off Time period is up, the pump and heater will restart.
Time Therapy LED goes solid, and the Setpoint LED is ashing.
Once the Setpoint is reached the Red LED ashes with a short
audible beep to let the operator/user know the next therapy cycle
has started.

OPERATOR'S MANUAL
TP702 T/PUMP
10 www.gaymar.com
TROUBLESHOOTING
TROUBLESHOOTING
Problem Possible Cause Remedy
T/Pump will not turn on. The electrical cord is not plugged
into a properly grounded Hospital
Grade receptacle.
Insert the plug fully into the properly
grounded Hospital Grade receptacle.
T/Pump will not pump. Water level is low or reservoir is
empty.
Rell with room temperature water
to proper level.
Flow indicator light is on. Water ow to pad or hose is
restricted.
Clamp is closed.
Water level is low or reservoir is
empty.
T/Pump is lled with water that is
too hot.
Straighten the hose.
Open the clamp.
Rell with room temperature water
to proper level.
Rell with room temperature water
to proper level.
Warning indicator & Audible
alarm (Flash / Beep).
A High Heat (42°C) or Cooling
Setpoint was selected
(10°C).
Loss of power while unit was in a
Therapy mode. (Possible Power
Fail.)
Unit is running after a 20- or 30-
minute “Off “therapy cycle period,
has reached the desired Setpoint, and
is now timing the 20- or 30- minute
On cycle period.
The unit just went into, or came out
of Lock mode.
Indication only: A Setpoint outside
body temperature range is selected.
Insert the plug fully into the
receptacle, place the unit into
Standby mode, then unplug the
T/Pump. If power is removed while
unit is in On-Mode, the Power Fail
alarm will beep for approximately 10
minutes.
Indication only to indicate an “On”
Therapy cycle period is timing.
Indication only.

OPERATOR'S MANUAL
TP702 T/PUMP
11www.gaymar.com
Problem Possible Cause Remedy
Warning indicator on with unit
in Standby mode.
Unit shut down in an over
temperature condition.
Empty the reservoir and rell with
room temperature water.
Make sure all clamps are open.
Press the On/Standby button.
Verify ow through the pad.
The Warning light will turn off
within 5 minutes.
Flow indicator and Standby
indicator are on with
T/Pump not pumping.
Unit detected a Flow warning for
more than 5 minutes, thus goes to
standby.
Reference “Flow indicator light is on”
above.
Correct the problem, and press the
On/Standby to put the unit back
into Run mode.
Temperature Setpoint light
blinking.
Unit is warming up to the selected
setpoint.
Unit is in Cooling mode, for longer
than 40 minutes.
Indication only.
Follow the shutdown procedure.
Drain the water in reservoir to ice
ll level, and rell with ice. Follow
the start-up procedure.
TROUBLESHOOTING

OPERATOR'S MANUAL
TP702 T/PUMP
12 www.gaymar.com
Problem Possible Cause Remedy
Both the Temperature and
Therapy Cycle Setpoint lights
are blinking.
Unit is in “Off” Therapy cycle time. Indication only.
T/Pump will not heat. Reservoir is empty.
Flow is blocked.
Rell with room temperature water
to proper level.
Reference “Flow indicator light is on”
above.
T/Pump will not cool. Reservoir is empty.
Flow is blocked.
Ice is depleted.
Rell with room temperature water
to proper level.
Reference “Flow indicator light is on”
above.
Drain excess water to Cooling
water line and ll remainder of
reservoir with ice.
Temperature or Therapy Time
buttons do not work.
The buttons have been locked. Press and hold the lock button for
two seconds.
Water leaks from hose
connectors.
Damaged O-ring.
Locking ring on Clik–Tite® connector
is not snapped into place (See
Figure 4 on page 7.)
Replace Clik–Tite® connector.
Snap Clik–Tite® connector shut.
TROUBLESHOOTING

OPERATOR'S MANUAL
TP702 T/PUMP
13www.gaymar.com
STORAGE / CLEANING
1. Close the hose clamps.
2. Disconnect the pad.
3. Connect ends of the connector hoses together, where applicable.
4. Open the hose clamps.
5. Leave water in the reservoir.
6. Coil and fasten the hose using the tube set strap and wrap the power
cord around the unit.
1. Drain the pump. (See instructions below.)
2. Coil the hose, rather than folding it, to prevent hose kinks.
3. Fasten the hose using the tube set strap and wrap the power cord
around the unit.
1. Disconnect the T/Pump from AC power.
2. Clamp the hose clamps.
3. Disconnect the pad or hoses from one another, keeping hoses at or
above the level of the T/Pump.
4. Open the hose clamps.
5. Remove the ll cap and invert the T/Pump over a sink.
6. When all uid has drained from the hoses and reservoir, replace the ll
cap.
7. Connect the hoses together, where applicable.
Storage (Short term)
Less than 1 day
Storage (Long term)
Draining
STORAGE / CLEANING

OPERATOR'S MANUAL
TP702 T/PUMP
14 www.gaymar.com
STORAGE / CLEANING
Institutional
(Hospital) Cleaning
Instructions
Pads / Accessories
Note: Change the water monthly or more often depending on use.
Clean the outer surfaces of the T/Pump with one of the following:
• A damp cloth and soapy water.
• A spray cleaner such as Fantastic®, 3M Phenolic Disinfectant®or
10% bleach solution.
Note: If water is contaminated or not changed for a month, please follow
the internal cleaning procedure below.
1. Prepare a germicidal solution according to the manufacturer's
instructions. Use Incidin Extra, available from Ecolabs, Inc.
2. Drain the pump.
3. Connect hose set together.
4. Fill the reservoir to the Heating water line on the back of the
reservoir.
5. Select the (35°C) temperature setpoint on the keypad.
6. Start the T/Pump, and circulate the solution for one hour.
7. Drain the solution and rell the pump with clean water.
NOTE: In a home environment, perform only step 2 and
the rell instructions in step 7.
Only use Mul•T•Pads®. The unique button design allows optimal water ow
and provides trouble-free operation when the pad is folded. This reduces
the number of different sizes of pads your facility must keep in inventory.
The Mul•T•Pads with Clik-Tite® connectors can be interconnected to
provide therapy to more than one body site at a time (Figure 1B,
page 2). Refer to Catalog Descriptions on page 3 for a list of various pads
and ordering information.

OPERATOR'S MANUAL
TP702 T/PUMP
15www.gaymar.com
PREVENTIVE
MAINTENANCE / SERVICE
Only qualied medical service personnel should repair the
T/Pump in accordance with the Service Manual.Improperrepair
mayresultindeathorseriousinjury,equipmentdamage,ormalfunction.
ToobtainacopyoftheServiceManual,contactyourlocaldealeror
Gaymar'sInternationalDepartmentorvisitourwebsitewww.gaymar.
com.
Riskofelectricshock. Disconnect power before servicing.
MAINTENANCE
WARNING
DANGER
WARNING
WARNING

OPERATOR'S MANUAL
TP702 T/PUMP
16 www.gaymar.com
SPECIFICATIONS
SPECIFICATIONS
TP702
Classication Class I equipment with Type BF applied part suitable for continuous
operation. Not classied for protection against ingress of liquid.
Not classied for use in the presence of ammable anesthetics.
Size (approx.) 11.5” x 8” x 8”
29.2cm x 20.3cm x 20.3cm
Weight 6.5 lbs (2.9 kg) when empty
9 lbs (4.0 kg) with unit lled with water to heating level
Reservoir capacity 93 oz (2.75 l) maximum
Flow rate 9 gph (34 lph) minimum with pad attached
Ambient operating
temperature
15.6°C to 32.2°C
Environmental conditions for
transport and storage
-28°C to 48°C
At uncontrolled RH
Temperature setpoints TP702 Professional
42°C
38°C
35°C
10°C
Average temperature
accuracy
±1°C at 42°C
Maximum Contact Surface
Temperature
42°C
High Limit Safety Temperature 43.3°C to 49°C
Power cord Modular: adaptable to Country of use
Current leakage 100 microamperes maximum
Ground resistance 0.5 ohm max
Electrical requirements
Voltage (VAC)
Frequency (Hz)
Current (amps)
230+10%
50 Hz
2.0 amperes
Certications MEDICAL ELECTRICAL EQUIPMENT WITH RESPECT TO
ELECTRICAL SHOCK, FIRE, AND MECHANICAL HAZARDS
ONLY IN ACCORDANCE WITH UL 60601-1 AND ASTM F 2196-
2002
IEC 60601-1-2

OPERATOR'S MANUAL
TP702 T/PUMP
17www.gaymar.com
Gaymar equipment and products are warranted against defects in
material and workmanship under normal use, and operation from the
date of purchase, for the time periods listed below for the respective
equipment and products. Except for such warranty, Gaymr disclaims all
other expressed and/or implied warranties including, but not limited to,
the implied warranties of merchantability and of tness for a particular
purpose.
All labor performed and parts provided free of charge for a period of one
(1) full year from the date of purchase, provided the equipment is returned
with prior authorization prepaid to Gaymar Industries.
Free replacement of product where defects in materials and/or
workmanship are evident at time of delivery, provided the product is
returned with prior authorization prepaid to Gaymar Industries.
Free replacement of product where defects in materials and/or
workmanship occur within 90 days from date of delivery, provided the
product is returned with prior authorization prepaid to Gaymar Industries.
Defective parts will be exchanged free of charge where defects in materials
and/or workmanship occur within 90 days from date of delivery, provided
the parts are returned with prior authorization prepaid to Gaymar
Industries.
WARRANTIES
WARRANTIES
PUMP
PAD, SINGLE
PATIENT USE
PAD, REUSABLE
PARTS

OPERATOR'S MANUAL
TP702 T/PUMP
18 www.gaymar.com
EMC INFORMATION
ENGLISH
The TP702 complies with EN60601-1-2: 2001 Second Edition
(CISPR Classied as Class B, Group 1 ISM equipment)
Medical Electrical Equipment needs special precautions regarding
EMC and needs to be installed and put into service according to
the EMC information provided in the following pages.
Portable and mobile RF communications equipment can effect
Medical Electrical Equipment.
CAUTION !
The TP702 should not be used adjacent to or stacked with other
equipment. If adjacent or stacked use is necessary, the TP702
should be observed to verify normal operation in the conguration
in which it will be used.