GE Security Concord 4 User manual

For a detailed review of the entire system, please view the Concord 4 system manual.
Arm and Disarm
Arm:
To arm all sensors in AWAY mode when you are leaving the premises, press [3] and enter your
[security code].
To arm all sensors in STAY mode when you are not leaving the premises, press [2] and enter your
[security code].
Disarm:
To disarm, enter your [security code] + [1].
Quick Guide: GE Security Concord 4

Battery
The Concord 4 operates on a UB 1270 battery.
Loss of AC power and use of backup battery power is indicated by NO AC.
A low battery condition is indicated by BAT.
For instructions on replacing your battery, please visit our Battery Replacement Page.
Bypassing Protected Areas
Bypassing a zone allows you to arm your system with certain protected areas intentionally unarmed. There
are two ways to bypass a zone: directly and indirectly.
To bypass a zone directly, first arm your system as normal.
Then, press [# Bypass] + enter your [security code].
The display will read “BYPASS SENSOR” _ _ “ or “ENTER SNSR _ _”.
Enter the desired sensor number.
The display will confirm with ‘BYPASSED ZONES _ _” or “SENSOR _ _ BYPASS”.
Continue to bypass more zones. If no more zones are desired, walk away, the system is armed.
To unbypass a zone, repeat the direct bypass process or close the bypassed doors/windows and arm
your system.
To bypass a zone indirectly, leave the desired doors/windows open and arm your system normally.
The display will read “PRO-TEST”. This is because sensors have been left open.
When the display reads “PRO-TEST”, press [# Bypass]. The display will read “BYPASSES ZONES _ _” or
“SENSOR _ _ BYPASSED”.
The system will sound arming level beeps to indicate that the system is armed and the open sensors
(doors./window) have been successfully bypassed.
The system is now armed with zones bypassed.
To unbypass a zone, close the bypassed zones and arm your system normally.
Change Time and Date
To change the system date:
Press [9] + [Master code] + [0] + [2] + [1].
Enter the current date as 6-digits, i.e., 082314 for August 23, 2014, then press [#].
Press [*] + [0] + [0] + [#] to exit.

To change the system time:
Press [9] + [Master code] + [0] + [2] + [0].
Enter the current time in 24-hour format, i.e., 1630 for 4:30pm, then press [#].
Press [*] + [0] + [0] + [#] to exit.
Chimes and Beeps
When your system is in chime mode, a chime alert will sound three tones whenever a protected door/window
is opened.
To turn chime mode on and off, press [7] + [1].
Reset
To clear the display after an alarm event, enter the sequence [1] + [security code] twice or enter [1] +
[security code] + [*].
Security Codes
You can program up to 230 users, each with their own level of security.
To add a new user, press [9] + [Master code] + [0] + [3] + [0] + [desired user number, i.e., 27 for user
27].
Enter the desired user 4-digit code + [#].
Press [*] + [0] + [0] + [#] to exit the menu.
To delete a user, press [9] + [Master code] + [0] + [3] + [0].
Enter the user number you wish to delete + [0] + [Master code] + [#].
Press [*] + [0] + [0] + [#] to exit the menu.
New users can be assigned attributes, which define what actions users can and cannot perform. For a
complete list of user attributes, please see the Concord 4 system manual.
Trouble Conditions
Trouble conditions are issues that require your attention and are indicated by rapid beeps sounding every
minute until the Trouble Condition is corrected.
To silence the Trouble Condition beeping, press [* Status].

For a list of possible Trouble Conditions, please see the Concord 4 system manual.
Volume
You can adjust the system status voice volume level at which system status messages are announced.
To adjust the system status voice volume, press [9] + [Master code] + [0] + [4] + [3].
Select a volume level, where 1 is the lowest and 7 is the highest, then press [#].
Press [*] + [0] + [0] + [#] to exit the menu.