GE ASTAT XB User manual

1 2 0 (4 .7 2 ) 3 7 .5 ( 1 .4 8 )
7 . 0 (0 .2 8 )
1
2
4
3

08477.A

+ GND -
+ GND -
- GND +- GND ++ - ~/+ ~/-
1
2
4
3
1 2 3 4 5 6
O N
1 2 3 4 5 6
O N
+ 1 6
+ 8
+ 4
+ 2
+ 1
0
0
0
0
0
11 5 9 1. B
1
2
3
4
5
6
7

0 32 06 . B
AMPS
C OD E
TEM P
S T AR T R N TR I P R S48 5
S TA R T
S T O P
+
R ESET
-
D AT A
PR OG
1
2
4
3

Soft Starter Remote Keypad
1/2
1 Description
The keypad can be mounted up to 3 metres away from the soft starter, allowing
remote control and monitoring.
2 Packing List
1 x keypad and faceplate
1 x Cable, B9, 3 metres
1 x Gasket, foam
1 x Instruction sheet
4 x M3 x 16 Screw
4 x M3 Flat washer
4 x M3 Spring washer
4 x M3 Nut
2 x Jack screw
3 Mounting the keypad
WAR I G
Models 105 A ( 55 kW): The keypad can be removed or replaced while
the starter is running. It is not necessary to remove mains or control
voltage.
Models > 105 A (> 55 kW): The busbar and/or heatsink are live whenever
mains voltage is connected. Remove mains and control voltage from the
soft starter before removing the cover.
1. Remove the faceplate.
2. Measure and drill four mounting holes and two holes for the B9 connector
(refer to Mounting Diagram on the back page).
3. Apply the foam gasket to the back of the keypad.
4. Align the keypad over the holes and screw in place. Tighten the screws so that
the foam gasket is compressed to half its original thickness.
OTE: If the screws are too loose, the gasket will not provide IP65 protection.
Overtightening the screws can damage the keypad, gasket or panel.
5. Plug the cable into the keypad and the soft starter.
6. Press the faceplate onto the front of the keypad.
1 Faceplate
2 Screw
3 Jack screw
4 Flat washer
5 Spring washer
6 Nut
7 Keypad
8 Gasket
9 Panel
10 Cable
13576.A
13575.A

Soft Starter Remote Keypad
2/2
4 Synchronising the Keypad and the Starter
The B9 cable can be connected/disconnected from the keypad while the starter is
running.
The first time a keypad is plugged into a starter, the
starter will copy its parameter settings to the keypad.
If the keypad has previously been used with a soft starter, the operator can select
whether to copy the parameters to the starter, or to copy the soft starter's parameter
settings into the keypad.
Select the required option using the and
buttons. Press E TER
to proceed with the selection.
OTE
If the parameter software version in the keypad is different from the
software version of the starter, only will be available.
OTE
While the keypad is synchronising, only the E TER and STOP
buttons are enabled.
5 Mounting Diagram
rill four mounting holes for screws (one in each corner) and two holes for the B9
connector.
OTE
Image is not to scale.
62 mm
6
8
m
m
13 mm
136 mm
1
4
2
m
m
13 mm
25 mm (x2)
4 mm (x4)
06159.C