GE Multilin F650 User manual

GE Multilin
215 Anderson Avenue
L6E 1B3 Markham, ON -CANADA
T [phone] F [phone]
E [email protected]
Internet: www.GEMultilin.com
Firmware version: 3.40
EnerVista F650 Setup version: 3.40
Copyright © 2006 GE Multilin
F650
Digital Bay Controller
Instruction manual
GEK-106310Q
GE Multilin
Avda. Pinoa, 10
48170 Zamudio SPAIN
T [phone] F [phone]
E [email protected]
gGE Consumer & Industrial
Multilin

GEK-106310Q F650 Digital Bay Controller I
TABLE OF CONTENTS
1. GETTING STARTED 1.1 IMPORTANT PROCEDURES
1.1.1 CAUTIONS AND WARNINGS...........................................................................1-1
1.1.2 INSPECTION CHECKLIST................................................................................1-4
1.1.3 SAFETY INSTRUCTIONS.................................................................................1-6
1.2 OVERVIEW
1.2.1 INTRODUCTION TO 650 FAMILY OF RELAYS ...............................................1-7
1.2.2 HARDWARE ARCHITECTURE.........................................................................1-7
1.2.3 SOFTWARE ARCHITECTURE..........................................................................1-9
1.2.4 COMMUNICATIONS ARCHITECTURE ............................................................1-9
1.3 ENERVISTA 650 SETUP SOFTWARE
1.3.1 SYSTEM REQUIREMENTS ............................................................................1-11
1.3.2 INSTALLATION................................................................................................1-11
1.3.3 CONNECTING ENERVISTA 650 SETUP WITH F650....................................1-16
1.4 650 HARDWARE
1.4.1 MOUNTING & WIRING....................................................................................1-17
1.4.2 650 COMMUNICATIONS.................................................................................1-17
1.4.3 FACEPLATE DISPLAY....................................................................................1-18
1.4.4 MAINTENANCE...............................................................................................1-19
2. PRODUCT DESCRIPTION 2.1 OVERVIEW
2.1.1 F650 OVERVIEW...............................................................................................2-1
2.2 SUMMARY
2.2.1 ANSI DEVICE NUMBERS AND FUNCTIONS...................................................2-2
2.3 ORDERING CODE
2.4 TECHNICAL SPECIFICATIONS
2.4.1 PROTECTION ELEMENTS...............................................................................2-6
2.4.2 CONTROL........................................................................................................2-17
2.4.3 MONITORING..................................................................................................2-21
2.4.4 USER-PROGRAMMABLE ELEMENTS...........................................................2-23
2.4.5 METERING......................................................................................................2-24
2.4.6 INPUTS............................................................................................................2-25
2.4.7 REAL TIME CLOCK.........................................................................................2-27
2.4.8 OUTPUTS........................................................................................................2-27
2.4.9 CONTROL POWER SUPPLY..........................................................................2-28
2.4.10 COMMUNICATIONS........................................................................................2-28
2.4.11 OPTIC FEATURES..........................................................................................2-30
2.4.12 ENVIRONMENTAL CHARACTERISTICS.......................................................2-31
2.4.13 PACKAGING AND WEIGHT............................................................................2-31
2.4.14 TYPE TESTS...................................................................................................2-31
2.4.15 APPROVALS ...................................................................................................2-31
2.5 EXTERNAL CONNECTIONS
3. HARDWARE 3.1 MODULE DESCRIPTION
3.2 POWER SUPPLY
3.3 MECHANICAL DESCRIPTION
3.3.1 MOUNTING........................................................................................................3-3
3.3.2 REAR DESCRIPTION........................................................................................3-6
3.4 WIRING
3.4.1 EXTERNAL CONNECTIONS.............................................................................3-9
3.4.2 DIGITAL INPUTS WITH TRIP CIRCUIT SUPERVISION ..................................3-9
3.4.3 CABLE/FIBER ETHERNET BOARD................................................................3-10

II F650 Digital Bay Controller GEK-106310Q
TABLE OF CONTENTS
3.5 TRANSCIEVER OPTICAL POWER BUDGET VERSUS LINK LENGTH
4. HUMAN INTERFACES.
SETTINGS & ACTUAL
VALUES
4.1 ENERVISTA 650 SETUP SOFTWARE INTERFACE
4.1.1 INTRODUCTION ................................................................................................4-1
4.1.2 ENERVISTA 650 SETUP SOFTWARE OVERVIEW..........................................4-1
4.1.3 MAIN SCREEN...................................................................................................4-3
4.1.4 COMMUNICATION MENU.................................................................................4-4
4.1.5 FILE MANAGEMENT .........................................................................................4-6
4.1.6 ENERVISTA 650 SETUP MENU STRUCTURE...............................................4-10
4.1.7 FILE MENU OVERVIEW ..................................................................................4-11
4.1.8 SETPOINT MENU OVERVIEW........................................................................4-15
4.1.9 ACTUAL VALUES MENU OVERVIEW.............................................................4-24
4.1.10 OPERATIONS MENU OVERVIEW ..................................................................4-27
4.1.11 COMMUNICATION MENU OVERVIEW...........................................................4-28
4.1.12 SECURITY MENU OVERVIEW........................................................................4-31
4.1.13 VIEW MENU OVERVIEW.................................................................................4-31
4.1.14 HELP MENU OVERVIEW ................................................................................4-31
4.2 HUMAN MACHINE INTERFACE (HMI)
4.2.1 DISPLAY...........................................................................................................4-32
4.2.2 FRONT LED INDICATORS ..............................................................................4-33
4.2.3 PUSHBUTTONS...............................................................................................4-33
4.2.4 FRONT PORT AND COVER SEALING SYSTEM............................................4-34
4.2.5 TEXT MENUS...................................................................................................4-35
4.2.6 GRAPHIC DISPLAY .........................................................................................4-54
4.3 WEB SERVER
4.3.1 HOME...............................................................................................................4-63
4.3.2 SNAPSHOT EVENTS.......................................................................................4-64
4.3.3 CONTROL EVENTS.........................................................................................4-65
4.3.4 ALARMS...........................................................................................................4-66
4.3.5 OSCILLOGRAPHY...........................................................................................4-67
4.3.6 FAULT REPORT ..............................................................................................4-68
4.3.7 DATA LOGGER................................................................................................4-69
4.3.8 METERING.......................................................................................................4-70
5. SETTINGS 5.1 OVERVIEW
5.1.1 SETTING MAIN MENU.......................................................................................5-1
5.2 PRODUCT SETUP
5.2.1 COMMUNICATION SETTINGS..........................................................................5-3
5.2.2 MODBUS USER MAP........................................................................................5-6
5.2.3 FAULT REPORT ................................................................................................5-7
5.2.4 OSCILLOGRAPHY.............................................................................................5-9
5.2.5 DATA LOGGER................................................................................................5-12
5.2.6 DEMAND .........................................................................................................5-14
5.3 SYSTEM SETUP
5.3.1 GENERAL SETTINGS......................................................................................5-20
5.3.2 FLEX CURVES.................................................................................................5-20
5.3.3 BREAKER.........................................................................................................5-22
5.3.4 SWITCHGEAR .................................................................................................5-24
5.4 PROTECTION ELEMENTS
5.4.1 CHANGE OF SETTING TABLES IN F650 ELEMENTS...................................5-25
5.4.2 INVERSE TIME CURVES CHARACTERISTICS..............................................5-29
5.4.3 PHASE CURRENT...........................................................................................5-39
5.4.4 NEUTRAL CURRENT ......................................................................................5-50
5.4.5 GROUND CURRENT .......................................................................................5-57
5.4.6 SENSITIVE GROUND CURRENT....................................................................5-60
5.4.7 NEGATIVE SEQUENCE CURRENT................................................................5-65
5.4.8 VOLTAGE ELEMENTS ....................................................................................5-66
5.4.9 POWER...........................................................................................................5-71

GEK-106310Q F650 Digital Bay Controller III
TABLE OF CONTENTS
5.5 CONTROL ELEMENTS
5.5.1 SETTING GROUP ...........................................................................................5-83
5.5.2 UNDERFREQUENCY ELEMENT (81U)..........................................................5-84
5.5.3 OVERFREQUENCY ELEMENT (81O)............................................................5-84
5.5.4 SYNCHRONISM CHECK ELEMENT - SYNCHROCHECK (25) .....................5-85
5.5.5 AUTORECLOSE (79).......................................................................................5-94
5.5.6 BREAKER FAILURE ELEMENT (50BF)........................................................5-101
5.5.7 VT FUSE FAILURE ELEMENT (VTFF) .........................................................5-104
5.5.8 BROKEN CONDUCTOR................................................................................5-105
5.5.9 LOCKED ROTOR ..........................................................................................5-106
5.5.10 PULSE COUNTERS......................................................................................5-107
5.5.11 ANALOG COMPARATORS...........................................................................5-109
5.5.12 FREQUENCY RATE OF CHANGE................................................................5-111
5.5.13 LOAD ENCROACHMENT..............................................................................5-112
5.6 INPUTS/OUTPUTS
5.6.1 INPUT/OUTPUT PLACEMENT......................................................................5-114
5.6.2 CONTROL SETTINGS FOR INPUTS/OUTPUTS..........................................5-115
5.6.3 INPUTS..........................................................................................................5-117
5.6.4 OUTPUTS......................................................................................................5-119
5.6.5 CIRCUIT SUPERVISION AND CONTACT SEAL-IN CIRCUITS...................5-121
5.6.6 ANALOG BOARDS SPECIFIC SETTINGS ...................................................5-131
5.6.7 VIRTUAL INPUTS..........................................................................................5-132
5.6.8 VIRTUAL OUTPUTS......................................................................................5-132
5.7 REMOTE COMMS
5.8 TESTINGS
5.8.1 FORCE IO–INPUT TESTING ........................................................................5-134
5.8.2 FORCE IO –OUTPUT TESTING ...................................................................5-134
5.9 RELAY CONFIGURATION
5.9.1 OUTPUTS......................................................................................................5-135
5.9.2 LEDS..............................................................................................................5-136
5.9.3 OPERATIONS................................................................................................5-137
5.9.4 PROTECTION ELEMENTS...........................................................................5-141
5.9.5 OSCILLOGRAPHY ........................................................................................5-142
5.9.6 CONTROL EVENTS......................................................................................5-143
5.9.7 SWITCHGEAR ..............................................................................................5-145
5.9.8 HMI (HUMAN-MACHINE INTERFACE).........................................................5-147
5.10 LOGIC CONFIGURATION (PLC EDITOR)
5.10.1 INTRODUCTION............................................................................................5-151
5.10.2 THEORY OF OPERATION............................................................................5-152
5.10.3 MAIN MENU...................................................................................................5-155
5.10.4 CONFIGURATION GENERATION................................................................5-157
5.10.5 GENERATION OF LIBRARIES .....................................................................5-158
5.10.6 EXAMPLE OF APPLICATION .......................................................................5-160
5.11 IEC 61850 CONFIGURATION
5.12 PROCOME CONFIGURATION
6. ACTUAL VALUES 6.1 FRONT PANEL
6.1.1 LEDS..................................................................................................................6-1
6.2 STATUS
6.2.1 OPERATION BITS.............................................................................................6-2
6.2.2 BREAKER..........................................................................................................6-2
6.2.3 PROTECTION....................................................................................................6-3
6.2.4 CONTROL ELEMENTS...................................................................................6-11
6.2.5 PROTECTION SUMMARY..............................................................................6-19
6.2.6 SNAPSHOT EVENTS SUMMARY...................................................................6-21
6.2.7 MODBUS USER MAP......................................................................................6-23
6.2.8 SWITCHGEAR STATUS..................................................................................6-23
6.2.9 CALIBRATION.................................................................................................6-24
6.2.10 FLEX CURVES ................................................................................................6-25
6.2.11 SYSTEM INFO.................................................................................................6-25

IV F650 Digital Bay Controller GEK-106310Q
TABLE OF CONTENTS
6.2.12 RECORD STATUS...........................................................................................6-25
6.3 METERING
6.3.1 PRIMARY VALUES ..........................................................................................6-29
6.3.2 SECONDARY VALUES....................................................................................6-33
6.3.3 PHASOR DIAGRAM.........................................................................................6-35
6.3.4 FREQUENCY...................................................................................................6-35
6.4 INPUTS / OUTPUTS
6.4.1 CONTACT INPUTS ..........................................................................................6-36
6.4.2 CONTACT OUTPUT STATUS..........................................................................6-37
6.4.3 CONTACT OUTPUT OPERATES....................................................................6-37
6.4.4 CONTACT OUTPUT RESETS .........................................................................6-38
6.4.5 I/O BOARD STATUS........................................................................................6-39
6.4.6 VIRTUAL INPUTS ............................................................................................6-39
6.4.7 VIRTUAL OUTPUTS ........................................................................................6-39
6.4.8 REMOTE OUTPUTS ........................................................................................6-40
6.4.9 REMOTE INPUTS ............................................................................................6-41
6.4.10 ANALOG INPUTS.............................................................................................6-42
6.5 RECORDS
6.5.1 EVENT RECORDER ........................................................................................6-43
6.5.2 WAVEFORM CAPTURE ..................................................................................6-46
6.5.3 FAULT REPORT ..............................................................................................6-47
6.5.4 DATA LOGGER................................................................................................6-48
7. IEC 61850 PROTOCOL 7.1 IEC61850 GENERIC SUBSTATION STATE EVENT (GSSE)
7.1.1 REMOTE DEVICES............................................................................................7-1
7.1.2 REMOTE INPUTS ..............................................................................................7-3
7.1.3 REMOTE OUTPUTS ..........................................................................................7-4
7.2 IEC 61850 PROFILE FOR F650
7.2.1 INTRODUCTION ................................................................................................7-6
7.2.2 ACSI CONFORMANCE STATEMENT...............................................................7-6
7.2.3 LOGICAL NODES ............................................................................................7-11
7.2.4 COMMON DATA CLASS..................................................................................7-29
7.2.5 DATASETS.......................................................................................................7-44
7.2.6 MAPPINGS BETWEEN TOC CURVES IN IEC 61850 AND F650 RELAY
IMPLEMENTATION............................................................................................7-46
7.2.7 ANALOG DATA UNITS AND SCALES.............................................................7-47
8. SECURITY 8.1 ADDING USERS
8.1.1 USER RIGHTS ...................................................................................................8-1
8.2 CHANGING PASSWORDS
8.3 ENABLING SECURITY
8.4 LOGING INTO ENERVISTA 650 SETUP
9. BOOTCODE AND
FIRMWARE UPGRADE 9.1 INTRODUCTION
9.1.1 COMMUNICATION PARAMETERS...................................................................9-2
9.2 BOOT CODE UPGRADE
9.3 FIRMWARE VERSION UPGRADE
9.3.1 FIRMWARE UPGRADE .....................................................................................9-9
9.4 STEP LIST SUMMARY FOR VERSIONS 1.70 AND LATER
9.4.1 BOOT CODE UPGRADE (*).............................................................................9-13
9.4.2 FIRMWARE UPGRADE (*)...............................................................................9-13

GEK-106310Q F650 Digital Bay Controller V
TABLE OF CONTENTS
10. COMMISSIONING 10.1 VISUAL INSPECTION
10.2 GENERAL CONSIDERATIONS ON THE POWER SUPPLY NETWORK
10.3 ISOLATION TESTS
10.4 INDICATORS
10.5 POWER SUPPLY TESTING
10.6 COMMUNICATIONS
10.7 VERIFICATION OF MEASUREMENT
10.7.1 VOLTAGES......................................................................................................10-7
10.7.2 PHASE CURRENTS........................................................................................10-7
10.7.3 ACTIVE, REACTIVE POWER, AND COSJ METERING .................................10-8
10.7.4 FREQUENCY...................................................................................................10-8
10.8 INPUTS AND OUTPUTS
10.8.1 DIGITAL INPUTS.............................................................................................10-9
10.8.2 CONTACT OUTPUTS....................................................................................10-10
10.8.3 CIRCUIT CONTINUITY SUPERVISION INPUTS .........................................10-10
10.8.4 LATCHING CIRCUITS...................................................................................10-10
10.9 CONNECTIONS FOR TESTING PROTECTION ELEMENTS
10.10 INSTANTANEOUS OVERCURRENT (50PH, 50PL, 50N, 50G Y 50SG)
10.11 TIME OVERCURRENT (51PH, 51PL, 51N, 51G AND 46)
10.12 DIRECTIONAL ELEMENTS (67P, 67N, 67G, 67SG)
10.12.1 67P ELEMENT...............................................................................................10-14
10.12.2 67N ELEMENT...............................................................................................10-14
10.12.3 67G ELEMENT ..............................................................................................10-16
10.12.4 67SG ELEMENT............................................................................................10-17
10.13 UNDERVOLTAGE ELEMENTS (27P, 27X)
10.13.1 27P ELEMENT...............................................................................................10-18
10.13.2 27X ELEMENT...............................................................................................10-18
10.14 OVERVOLTAGE ELEMENTS (59P, 59X, 59NH, 59NL, 47)
10.14.1 59P ELEMENT...............................................................................................10-19
10.14.2 59X ELEMENT...............................................................................................10-19
10.14.3 59NH AND 59NL ELEMENTS .......................................................................10-20
10.14.4 47 ELEMENT - NEG SEQ OV .......................................................................10-21
10.15 FREQUENCY ELEMENTS (81O/81U)
10.16 RECLOSER (79)
10.16.1 RECLOSING CYCLE.....................................................................................10-23
10.16.2 RECLOSER STATUS....................................................................................10-24
10.16.3 EXTERNAL RECLOSE INITIATION..............................................................10-24
10.17 THERMAL IMAGE ELEMENT (49)
11. APPLICATION EXAMPLES 11.1 EXAMPLE 1: COMMUNICATION & PROTECTION SETTINGS
PROCEDURE
11.1.1 DESCRIPTION OF THE EXERCISE...............................................................11-1
11.1.2 PROCEDURE TO COMMUNICATE WITH THE RELAY.................................11-1
11.1.3 PROCEDURE TO SET THE PROTECTION FUNCTION................................11-3
11.1.4 TEST................................................................................................................11-4
11.2 EXAMPLE 2: TOC PROTECTION + RECLOSING SETTINGS
PROCEDURE
11.2.1 DESCRIPTION OF THE EXERCISE...............................................................11-5
11.2.2 PROCEDURE TO COMMUNICATE THE RELAY...........................................11-5
11.2.3 PROCEDURE TO SET THE PROTECTION FUNCTION................................11-5
11.2.4 PROCEDURE TO SET THE RECLOSER ....................................................... 11-6
11.2.5 PROCEDURE TO SET THE SYNCHROCHECK ............................................11-6

VI F650 Digital Bay Controller GEK-106310Q
TABLE OF CONTENTS
11.3 EXAMPLE 3: PROCEDURE TO SET AN OPERATION
11.3.1 DESCRIPTION OF THE EXERCISE................................................................11-8
11.3.2 PROCEDURE ..................................................................................................11-8
11.3.3 TEST...............................................................................................................11-10
12. FREQUENTLY ASKED
QUESTIONS 12.1 COMMUNICATIONS
12.2 PROTECTION
12.3 CONTROL AND HMI
12.4 RELAY CONFIGURATION
13. TROUBLESHOOTING
GUIDE 13.1 SYMPTOMS AND RECOMMENDED ACTIONS
A. LOGIC OPERANDS A.1 LOGIC OPERANDS
B. MODBUS PROTOCOL B.1 ACCESS TO F650 DATA
B.2 MODBUS F650
B.2.1 FUNCTIONS USED...........................................................................................B-2
B.2.2 PHYSICAL LAYER............................................................................................B-3
B.2.3 DATA LINK LAYER ...........................................................................................B-4
B.2.4 GENERIC READING.........................................................................................B-5
B.2.5 GENERIC WRITING..........................................................................................B-6
B.2.6 FUNCTION CODES .........................................................................................B-7
B.2.7 EXCEPTIONS AND ERROR RESPONDS........................................................B-8
B.3 DATA TYPE
B.4 MODBUS APPENDIX
B.4.1 DATA MANAGEMENT ....................................................................................B-10
B.4.2 WRITING SETTINGS ......................................................................................B-11
B.4.3 SNAPSHOT EVENTS......................................................................................B-12
B.4.4 OPERATIONS .................................................................................................B-15
B.5 OUTPUT WRITING
B.5.1 CONTROL EVENTS........................................................................................B-17
B.5.2 EVENT STRUCTURE......................................................................................B-18
B.6 EVENTS STATUS REQUEST (ALARMS)
B.6.1 CONTROL EVENTS RETRIEVAL FROM THE COMMAND LINE .................B-21
B.6.2 SERIAL COMUNICATION...............................................................................B-22
B.6.3 ETHERNET COMMUNICATION .....................................................................B-23
B.6.4 ACKNOWLEDGEMENT OF EVENTS (ALARMS)...........................................B-24
B.6.5 VIRTUAL INPUTS WRITING...........................................................................B-25
B.6.6 USER MAP......................................................................................................B-26
B.6.7 RETRIEVING OSCILOGRAPHY.....................................................................B-27
B.6.8 TIME SYNCHRONIZATION ............................................................................B-28
B.6.9 ENQUEUEING MESSAGES ..........................................................................B-29
B.6.10 TRACES AND TROUBLESHOOTING.............................................................B-30
B.6.11 MODBUS CHECK FUNCTION........................................................................B-31
B.7 MEMORY MAP

GEK-106310Q F650 Digital Bay Controller VII
TABLE OF CONTENTS
C. DNP 3.0 PROTOCOL FOR
F650 C.1 DNP 3.0 PROTOCOL SETTINGS
C.2 DNP 3.0 DEVICE PROFILE DOCUMENT
C.3 IMPLEMENTATION TABLE
C.4 BINARY INPUT POINTS
C.5 DNP CONFIGURATION EXAMPLES
C.5.1 CONFIGURING DNP USER MAP...................................................................C-11
C.5.2 EXAMPLE OF CUSTOM BINARY INPUT POINTS MAP................................C-13
C.5.3 MULTIPLE DNP 3.0 MASTERS COMMUNICATION WITH F650...................C-14
C.6 BINARY OUTPUT AND CONTROL RELAY OUTPUT
C.7 BINARY COUNTERS
C.8 ANALOG INPUTS
D. IEC 60870-5-104 PROTOCOL D.1 INTRODUCTION
D.2 TECHNICAL DESCRIPTION
D.3 BASIC APPLICATION FUNCTIONS
D.4 IEC 104 SETTINGS
D.5 IEC 60870-5-104 POINT LIST
E. PROCOME PROTOCOL E.1 PROCOME PROTOCOL
F. FACTORY DEFAULT LOGIC F.1 FACTORY DEFAULT LOGIC
G. FACTORY DEFAULT
CONFIGURATION G.1 FACTORY DEFAULT SETTINGS
G.2 FACTORY DEFAULT CONFIGURATION
H. MISCELLANEOUS H.1 GE MULTILIN WARRANTY

VIII F650 Digital Bay Controller GEK-106310Q
TABLE OF CONTENTS

GEK-106310Q F650 Digital Bay Controller 1-1
1 GETTING STARTED 1.1 IMPORTANT PROCEDURES
1
1 GETTING STARTED 1.1IMPORTANT PROCEDURES 1.1.1 CAUTIONS AND WARNINGS
To help ensure years of trouble free operation, please read through the following chapter for information to help guide you
through the initial installation procedures of your new relay.
BEFORE ATTEMPTING TO INSTALL OR USE THE RELAY, IT IS IMPERATIVE THAT ALL WARNINGS AND CAUTIONS
IN THIS MANUAL ARE REVIEWED TO HELP PREVENT PERSONAL INJURY, EQUIPMENT DAMAGE, AND/OR
DOWNTIME.
CAUTION: THE OPERATOR OF THIS INSTRUMENT IS ADVISED THAT IF THE EQUIPMENT IS USED IN A MANNER
NOT SPECIFIED IN THIS MANUAL, THE PROTECTION PROVIDED BY THE EQUIPMENT MAY BE IMPAIRED.
Figure 1–1: FRONT VIEW OF F650 UNITS