GE RAVTRANS1CO User manual

49-5000845 Rev. 0 10-23
RAVTRANS1CO will fit an existing First Company VTAC plenum with a 21 3/8” wide by 43 3/4 inch tall plenum
Installation Instructions
for your new
RAVTRANS1CO
Transition Plenum
For replacing an existing First Company VTAC that
has a 21 3/8” wide by 43 3/4” tall plenum with a new
Ultimate V10, V11, or V12 VTAC.
Before you begin - Read these instructions completely and carefully.
IMPORTANT – OBSERVE ALL GOVERNING CODES AND ORDINANCES.
Note to Installer – Be sure to leave these instructions with the Consumer.
Note to Consumer – Keep these instructions with your Owner’s Manual for future reference.
STOP!
Critical Closet Dimensions apply. Please review these required clearances & read the entire manual before
proceeding, to ensure that this kit will work for your application!
Tools Needed:
• Phillips Screwdriver
• 5/16” Nut Driver • Reciprocating Saw (front install only) • Circular Saw or Table Saw
C. V12 Series Unit: Top View
຿»๢´
຿»๢´
ï»๢´
28.35”
ເ»๢´+
´+
NOTE: For
side installation
FRQ¿JXUDWLRQ
a service
opening of 27” is
recommended.
NOTE: For
side installation
FRQ¿JXUDWLRQ
a service
opening of 31” is
recommended.
A. Closet: Top View
4” MIN 4” MIN
27” MIN
EXISTING SLEEVE
B. V10 or V11Series Unit: Top View
31” MIN FROM
SLEEVE EDGES
(V12 Series...with
Make up Air)
27” MIN FROM
SLEEVE EDGES
(V10/V11 non
MUA install)
* Refer to Notes
for side install
openings
* Warning - some 1st company access panels may not meet minimum opening requirements listed here, and may require reframing.
A duct adapter may also need to be constructed to adapt the round ducting to the existing rectangular ducting.

249-5000845 Rev. 0 10-23
Parts Included:
• Transition Plenum
• 6 self-driller screws (8#12.5mm)
• 24 screws (10#16*12.5mm)
• PVC elbow and tube for drain
• Diverter baffle plates (3)
• Diverter baffle support legs (4)
• Mounting bracket plates (3)
• Screws (2 pre-installed on MUA plate)#10-16 16.6 X12.5mm)
• Screws (4 self tapping) 4.2*25mm
Installation Instructions
Installation Overview:
Adapter plenum shown installed without RAVDPLAT insta platform and installed with 3 mounting brackets in bent
FRQ¿JXUDWLRQ
Optional Make up air
port (sealed) Plenum Adaptor
Single Diverter Plate
GLYHUWHUEDႉHVXSSRUW
legs shown per side, some
installations only require 1. Existing First Company
VTAC Plenum
Mounting brackets (3x),
optional depending on install
FRQ¿JXUDWLRQ
Mounting brackets (3x),
optional depending on install
FRQ¿JXUDWLRQ
Mounting brackets (3x),
optional depending on install
FRQ¿JXUDWLRQ
Screws (10#-16*12.5MM
24 total)
Screws - 10#-
16*12.5MM
24 total
Screws (10#-
16*12.5MM 24
total)
Self-driller screws
(8#12.5 - 6 total)
Self-driller screws
(8#12.5 - 6 total)
Self-driller screws
(8#12.5 - 6 total)

349-5000845 Rev. 0 10-23
Installation Instructions
STEP 2 :
• 5HPRYHWKHH[LVWLQJ)LUVW&RPSDQ\%DႉHE\UHPRYLQJWKHVFUHZVVHFXULQJLWFXWWLQJWKHVHDODQWDQGGLVFDUGLW
• (QVXUHWKHH[LVWLQJSOHQXPLVLQVWDOOHGFRUUHFWO\LQWKHZDOOZLWKDWOHDVWDï»๞EXEEOHWLOWWRZDUGVWKHRXWVLGH
ï»๞%XEEOH
Sealant
Screws
STEP 3 :
If your First Company Plenum has the lower triangular gussets, cut out the triangular gussets:
Cut edge of sleeve
gusset
&XW+HUH
&XW+HUH
Before
Note: The sheet metal
may be cut with any
suitable cutting tool,
take care of treating
sharp edges to avoid
injury after cutting the
gussets. After
STEP 1:
Prepare Installation area by removing the existing First Company VTAC unit.
WARNING 5LVNRI(OHFWULFDO6KRFNFDQFDXVHLQMXU\RUGHDWK%HIRUHVHUYLFLQJVZLWFKSRZHURႇDWWKH
service panel and lock the area to prevent power from being switched on accidentally.

449-5000845 Rev. 0 10-23
Installation Instructions
STEP 5:
,QVWDOOUHDUEDႉHH[WHQVLRQOHJVDVVKRZQDQGVHFXUHZLWKVKHHWPHWDOVFUHZVLILQVWDOOLQJDVLQJOHSLHFHEDႉH
STEP 4:
'HWHUPLQHWKHVL]HRIWKHQHZEDႉHQHHGHGWREHLQVWDOOHG7KHSDUWVLQFOXGHGFDQSURYLGHIRUWKHIROORZLQJGHSWKV
Note: 7RGHWHUPLQHWKHFRUUHFWEDႉHGHSWKQHHGHGUHIHUWRLPDJHLQVWHS
ñ»๞´%DႉHIRU
9” Deep Plenum ñ»๞´%DႉHIRU 13” Deep Plenum ñ»๞´7HOHVFRSLQJEDႉHXVHLQ FRQMXQFWLRQZLWKRWKHUEDႉHV
for 21” or deeper plenums
AB C
Measure the depth of the rear
ÀDQJHWRWKHSOHQXPJDVNHWWR
GHWHUPLQHGHVLUHGEDႉHGHSWK
%DႉHGHSWKWRPDWFK
plenum measurement
(Panels A and B only, when
installed individually)
Screw

549-5000845 Rev. 0 10-23
Installation Instructions
STEP 7:
,QVWDOOWKHSUHYLRXVO\VHOHFWHGEDႉHSODWHDQGVHFXUHLWZLWKHLWKHURUVFUHZVGHSHQGLQJRQWKHGHSWKRIWKHEDႉH
plate selected):
STEP 6:
,ILQVWDOOLQJDSLHFHEDႉHFRQ¿JXUDWLRQIRUGHHSHUSOHQXPVRQO\WKDWUHTXLUHVEDႉHSODWHVWREHXVHGLQWDQGHP
LQVWDOOWKHIURQWEDႉHH[WHQVLRQOHJV:KHQLQVWDOOLQJ$&RU%&EDႉHSODWHV
Extra support leg for deeper
SLHFHEDႉHLQVWDOODWLRQVRQO\
(QVXUHUHDURIEDႉH
SODWHLVÀXVKZLWKWKH
outdoor grille. Ensure
the inner edge attaches
correctly to the plenum
adapter (see next
step). failure to do so
may result in hot air
recirculation on the
condenser and poor
performance of the
VTAC.
Screw - one
on each side
A or B
Screws, 2 on each side
A or B
C

649-5000845 Rev. 0 10-23
Installation Instructions
STEP 9:
Secure the plenum adapter:
• If the Plenum extends into the closet, beyond the drywall, manually bend the 3 installation brackets 90 degrees
and secure the brackets as shown with 4 screws between the adapter and the plenum.
•,IWKHSOHQXPLVÀXVKZLWKWKHFORVHWZDOO\RXPD\HLWKHULQVWDOOWKHLQVWDOODWLRQEUDFNHWVÀDWDJDLQVWWKHZDOODQG
secure with 4 screws going into the studs as shown, OR you may drive 4 screws into the sides of the adapter as
shown through the plenum and into the studs.
• Installation Options:
STEP 8:
,QVWDOOSOHQXPDGDSWHU6WDUWDWWKHERWWRPDQGLQVHUWWKHDGDSWHUXQWLOLWLVÀXVKZLWKWKHH[LVWLQJ)LUVW&RPSDQ\
plenum:
NoteWKHDGDSWHUVKRXOG¿WLQVLGH
the existing plenum gasket.
Secure the front of
WKHEDႉHSODWHZLWK
provided sheet metal
screws
Note - if installing a make-
up air equipped VTAC,
the upper square block
RႇSODWHPXVWEHUHPRYHG
by removing the 2 screws
securing it.
Secure 3 brackets
with sheet metal srews
provided.
8VH¿HOGVXSSOLHGVFUHZV
to attach to framing
Brackets straight if inner
VLGHRISOHQXPLVÀXVK
with the wall Brackets bent if inner
side of plenum is proud
of the wall
No brackets may be used
if side clearances within
the closet are an issue.
Bend brackets 90
degrees at bend line and
attach to the plenum with
provided self-tapping
screws.
'ULYH¿HOGSURYLGHG
screws into the wall
framing or existing
plenum via provided
holes

749-5000845 Rev. 0 10-23
Installation Instructions
STEP 11:
39&GUDLQDJHSLSHLQVWDOODWLRQDQGRSWLRQDOVHFRQGDU\GUDLQRSWLRQV¿HOGVXSSOLHG
Install the primary drain tube supplied with the kit pointing straight towards the outdoor grille.
A secondary drain is available in the platfom, and may be left open or plumbed to the outside.
STEP 10:
Measure and cut 2x4 legs for RAVDPLAT installation. The legs must be cut to install a level installation of the platform.
• :LWKWKH5$9'3/$7LQSODFHDQGOHYHO
measure from the bottom of the platform
and add 3 inches for the length of the legs
• The legs must be cut to install a level
installation of the platform.
• :LWKWKH5$9'3/$7LQSODFHDQGOHYHOPHDVXUH
IURPWKHERWWRPRIWKHSODWIRUPWRWKHÀRRUDQG
add 3 inches for the needed length of the legs
'LVWDQFHWRÀRRUSOXV´
NoteWKLVZRXOGEHDJRRGWLPHWRHQVXUHWKHRULJLQDO¿UVWFRPSDQ\SOHQXPGUDLQLVIXQFWLRQDO
Install (2x) 2x4 legs here
Primary Drain
Optional secondary
drain. If left open, will
drain into the old plenum
drain pan.
Primary drain tube must
face the outside wall.
(Facing the knock out)

849-5000845 Rev. 0 10-23
Printed in the United States
STEP 12:
Install RAVDPLAT, ensure levelness.
STEP 13:
Install your new Ultimate V10, V11, or V12 VTAC per the instructions included with the unit.
Installation Instructions
At this point, it is recommended to test
the drainage by pouring a cup of water
onto the drain platform to ensure it
functions properly without any leaks.

49-5000845 Rev. 0 10-23
Instructions d’installation pour le
nouveau
RAVTRANS1CO
Plénum de transition
Pour remplacer un climatiseur terminal monobloc
(CTM) d’origine existant qui a un plénum de 21 3/8
po de large par 43 3/4 po de haut par un nouveau
CTM Ultimate V10, V11 ou V12.
Avant de commencer - Veuillez lire ces instructions attentivement et en totalité.
IMPORTANT – OBSERVEZ TOUS LES CODES ET RÈGLEMENTS EN VIGUEUR.
Note à l’installateur – Assurez-vous de laisser ces instructions au consommateur.
Note au consommateur - Conservez ces instructions avec votre manuel d’utilisation pour consultation ultérieure.
GE est une marque de commerce de General Electric Company. Fabriqué sous licence de marque.
Le RAVTRANS1CO s’adaptera à un plénum CTM d’origine existant avec un plénum de 21 3/8 po de large par 43 3/4 po de
hauteur
ARRÊTEZ!
Les dimensions de l’armoire doivent être très précises. Veuillez étudier les dimensions requises et lire le manuel en entier avant
de continuer, afin de vous assurer que cette trousse conviendra à votre application!
Outils nécessaires :
• Tournevis à pointe cruciforme
• Tournevis à douille 5/16 po • Scie alternative (installation frontale seulement) • Scie circulaire ou scie à table
C. Unité de série V12 : Vue de dessus
຿»๢´
຿»๢´
ï»๢´
´
ເ»๢´+
´+
REMARQUE : Pour
XQHFRQ¿JXUDWLRQ
d’installation
latérale, une
ouverture de
service de 27 po est
recommandée.
REMARQUE : Pour
XQHFRQ¿JXUDWLRQ
d’installation
latérale, une
ouverture de
service de 27 po est
recommandée.
A. Armoire : Vue de dessus
´0,1 ´0,1
´0,1
*$,1((;,67$17(
B. Unité de série V10 ou V11 :
Vue de dessus
´0,1'(38,6
/(6%25'6'(/$
*$,1(6pULH9
avec air d’appoint)
´0,1'(38,6
/(6%25'6'(/$
*$,1(,QVWDOODWLRQ
V10/V11 sans air
d’appoint)
* Se référer aux
REMARQUES
pour les ouvertures
d’installation
latérales
* Avertissement - Certains panneaux d’accès d’origine peuvent ne pas répondre aux exigences minimales d’ouverture énumérées ici, et peuvent
QpFHVVLWHUXQUHFDGUDJH,OIDXGUDSHXWrWUHFRQVWUXLUHXQDGDSWDWHXUGHFRQGXLWSRXUDGDSWHUOHFRQGXLWURQGDXFRQGXLWUHFWDQJXODLUHH[LVWDQW

249-5000845 Rev. 0 10-23
Instructions d’installation
Pièces incluses :
• Plénum de transition
• 6 vis autoperceuses (no 8 12,5 mm)
• 24 vis (no 10-16* 12,5 mm)
• Coude en PVC et tuyau pour drain
• Plaques de déflecteur (3)
• Pieds de support de déflecteur (4)
• Plaques de support de montage (3)
• Vis (2 préinstallées sur la plaque d’air d’appoint) no 10-16 16,6 x 12,5 mm)
• Vis (4 autotaraudeuses) 4,2*25 mm
Aperçu de l’installation :
,OOXVWUDWLRQGXSOpQXPDGDSWDWHXULQVWDOOpVDQVSODWHIRUPHG¶LQVWDOODWLRQ5$9'3/$7HWDYHFVXSSRUWVGHPRQWDJHHQFRQ¿JXUDWLRQ
courbée.
2UL¿FHG¶DLUG¶DSSRLQWHQ
option (scellé) Adaptateur de plénum
3ODTXHGHGpÀHFWHXUVLPSOH
'HX[SLHGVGHVXSSRUWGH
GpÀHFWHXULOOXVWUpVGHFKDTXH
côté, certaines installations en
nécessitent un seul. Plénum de CTM d’origine
existant
Supports de montage (x3), en
RSWLRQVHORQODFRQ¿JXUDWLRQ
d’installation
Supports de montage (x3), en
RSWLRQVHORQODFRQ¿JXUDWLRQ
d’installation
Supports de montage (x3), en
RSWLRQVHORQODFRQ¿JXUDWLRQ
d’installation
9LV1RPP
24 au total)
9LV1R
16*12,5 mm,
24 au total)
9LV1R
16*12,5 mm,
24 au total)
Vis autoperceuses
(no 8*12,5 mm, 6
total)
Vis autoperceuses (no
8*12,5 mm, 6 total)
Vis autoperceuses (no
8*12,5 mm, 6 total)