GE GVS04BDWASS Safety guide

ge.com
.1-!
U
Safety Instructions ........... 2,3
Installation Instructions ....... 4
Operating Instructions
Control Settings ..................... 5
Interior Space ....................... 6
Care and Cleaning ............ 7-9
Replacing the Light Bulb ............. 8
Reversing the Door .................. 9
Troubleshooting Tips ...... lo, 11
Consumer Support
Consumer Support ........ back cover
Product Registration (Canada) . .15, 16
Product Registration (U.S.) ...... 13, 14
Warrantg (Canada) ................ 18
Warrantg (U.S.) .................... 17
Refroidisseur
a boissons et
% •
Cl VII3
La section frangaise commence 5 la page 19
Centro
de bebidas
g enfriador
de vinos
La secci6n en espafiol empieza en la p6gina 33
Write the model and serial
numbers here:
Model #
Serial #
Find these numbers inside the
beverage center/wine chiller
on the left side. 197D4613PO04 49-60563 04-08 JR

IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
WARNING!
Use this appliance only for its intended purpose as described in this Owner's Manual.
SAFETYPRECAUTIONS
When using electrical appliances, basic safety precautions should be followed, including
the following:
This beverage center/wine chiller must be
properly installed and located in accordance
with these instructions before it is used.
iiiB,
Donot allow children to climb, stand or hang
on the shelves in the beverage center/wine
chiller. They could damage the beverage
center/wine chiller and seriously injure
themselves.
iiiB,
Donot store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
Before replacing a burned-out light bulb,
the beverage center/wine chiller should be
unplugged in order to avoid contact with a live
wire filament. (A burned out light bulb may
break when being replaced.)
Keep fingers out of the "pinch point" areas;
clearances between the doors and between
the doors and cabinet are necessarily small.
Becareful closing doors when children are
in the area.
Unplug the beverage center/wine chiller before
cleaning and making repairs.
NOTE:Westronglg recommend that ang
servicing be performed bg a qualified individual.
Donot store or install this appliance outdoors.
DANGER! RISK OF CHILD ENTRAPMENT
PROPERDISPOSALOF THEBEVERAGECENTERA/VINECHILLER
Child entrapment and suffocation are not
problems of the past. Junked or abandoned
refrigeration products are still dangerous.., even
if they will sit for "just a few days." If you are
getting rid of your old appliance, please follow
the instructions below to help prevent accidents.
Before You Throw Away Your Old
Refrigeration Product:
iiiilDiiiiiTake off the doors.
Refrigerants
All refrigeration products contain refrigerants,
which under federal law must be removed prior
to product disposal. If you are getting rid of an old
refrigeration product, check with the company
handling the disposal about what to do.
Leavethe shelves in place so that children
may not easily climb inside.
USEOF EXTENSION CORDS
Because of potential safety hazards under certain conditions, we strongly recommend against
the use of an extension cord.
However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed, 3-wire
grounding type appliance extension cord having a grounding type plug and outlet and that the electrical
rating of the cord be 15 amperes (minimum) and 120 volts.
2

_e.COtTI
HOW TOCONNECTELECTRICITY
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.
For personal safety, this appliance must be properly grounded.
The power cord of this appliance is equipped
with a 3-prong (grounding) plug which mates
with a standard 3-prong (grounding) wall outlet
to minimize the possibility of electric shock hazard
from this appliance.
Have the wall outlet and circuit checked by
a qualified electrician to make sure the outlet
is properly grounded.
If you have only a standard 2-prong wall outlet,
it is your personal responsibility and obligation
to have it replaced with a properly grounded
3-prong wall outlet.
The beverage center/wine chiller should always
be plugged into its own individual electrical outlet
which has a voltage rating that matches the
rating plate.
This provides the best performance and also
prevents overloading house wiring circuits which
could cause a fire hazard from overheated wires.
Never unplug your beverage center/wine chiller
by pulling on the power cord. Always grip plug
firmly and pull straight out from the outlet.
Immediately repair or replace all power cords
that have become frayed or otherwise damaged.
Do not use a cord that shows cracks or abrasion
damage along its length or at either end.
When moving the beverage center/wine chiller
away from the wall, be careful not to roll over
or damage the power cord.
READAND FOLLOWTHISSAFETYINFORMATIONCAREFULLY.
SAVETHESEINSTRLICTIONS

Installing the beverage center/wine chiller.
Removing the Packaging
Before using the beverage center/wine chiller, be sure all packing materials and tape
have been removed, including the protective film covering the control and any film
protecting the cabinet.
If gou are discarding an old refrigeration product, removethe doors to reduce
the danger of children beingtrapped inside.
Installation Guidelines
The beverage center/wine chiller can be
freestanding or can be installed under
the counter, with proper clearances.
iiiiliiiii;,
Allow the following clearances for ease
of installation, proper air circulation
and electrical connections:
Eachside !/2" (!2,7 mm)
Top 2" (51 mm)
Back 2" (5! mm)
iiiiliiiii;,
Before connecting the appliance
to the power source, let it stand upright
for approximatelg 2 hours. This will
reduce the possibilitg of a malfunction
in the cooling sgstem from handling
during transportation.
iiiiliiiiii
iiiiliiiii;,
iiiiiiiiii_
Do not install the beverage center/
wine chiller where the temperature
will go below 55°F (!2,7°C) or above
90°F (32,2°C).If the room temperature
is below the temperature setting, the
beverage center/wine chiller will not
operate (for instance, if the room is
at 55°F(!2,7°C) and the setting is 60°F
(!5,6°C), the unit will not run).
Install it on a level floor.
Donot install the beverage center/wine
chiller where it will be subject to direct
sunlight, heat or moisture.
Donot store or install this appliance
outdoors.
Im
To raise the appliance
Leveling Legs
Adjustable legs at the front corners
of the beverage center/wine chiller
should be set so the beverage center/
wine chiller is firmlg positioned on the
floor, with a 1/8" tilt to the back to help
the door closure.
To adjust the leveling legs, turn the legs
counterclockwise to raise the beverage
center/wine chiller, clockwise to lower it.
Handle
Door Handle
The door handle and screws are shipped
in a hardware bag attached to one
of the shelves inside the cabinet.
Locate the door handle and two screws.
Secure the door handle to the side
of the door as shown.
Door
4

About the controland settings.
Auto Bev
IndicatorLight
ge.com
ControlSettings
The temperature range of the beverage center/
wine chiller is intended for 40°F (4,4°C) to 60°F
(!5,6°C). The displagshows the average
temperature of the appliance. It is normal
for the actual temperature to varg slightlg
during operation.
Auto Temperature Setting
When the appliance is plugged in or the "+" pad
is pressed, the appliance runs on the "Auto Bey"
setting of/4/4°F(6,7°C)and the "Auto Bey"
indicator light in the upper left corner stags lit.
NOTE:Display will flash when the "+" pad is
pressed.
Normal Temperature Setting
The temperature of the beverage center can
be set anywhere between 39°F (3,9°C)to 61°F
(16,1°C)bg the "+" and "-" pads.
O Press and hold the SETpad. You will hear
a series of 2 beeps.
O After the second beep, press the "+" and "-"
pads to increase or decrease the desired
temperature in increments of one degree.
During this time the displeg will flash.
PressSETto confirm gour choice. The displeg
will stop fleshing. If no confirmation is made
in ten seconds, the unit will automatically
accept gour change.
NOTE:When gou change the temperature
setting, there mag be e 5-minute delay until
the compressor starts to run.
Fahrenheit and Celsius
The temperature displeg can be changed
between Fahrenheit end Celsius bg pressing and
holding the "+" pad for approximatelg 5 seconds.
Indicator Light
The D indicator islit when the compressor is
running to cool gour unit. It will not be lit when
the compressor is idle.
_lnterior Light
Toswitch the interior light on/off, simplg press
the [] pad.
When the Beverage Center/Wine Chiller is
After plugging in the beverage center/wine
chiller and setting the desired temperature,
allow the beverage center/wine chiller to reach
the set temperature before loading gout wine.
The temperature mag take up to 12 hours to
completelg stabilize.
After loading the wine or beverages, gou mag
notice the actual temperature rise. This is normal.
The actual temperature will continue to change
as the wine and beverages are cooled to the set
temperature. The temperature mag take up to
12 hours to completelg stabilize.
A guide with wine serving temperature suggestions
is located on the inside right portion of the unit.
It gives recommended temperatures for different
wines, as well as instructions on adjusting the
temperature of the beverage center/wine chiller.
NOTE:The exterior of the cabinet mag get warm.
This is normal.
Plugged In
_o i "o oQ" "
Interior Light
You can turn the light ON or OFFbg pushing the
light switch located on the right side of the control
panel housing. If the interior light is left on,
it will raise the inside temperature.

About the interior space.
Wooden Shelves
Wooden shelves in the beverage center/
wine chiller are removable for easg
cleaning and for storing larger items.
To remove ashelf, open the door
completelg to avoid potential damage
to the shelf. Lift slightlg and pull the shelf
forward. The shelf mag fit tightlg in the track.
To repluce u shelf, open the door completelg
to avoid potential damage to the shelf.
Slidethe shelf into the tracks along
the sides of the cabinet until it stops.
Wine end Beveroge Looding
Aswith ang refrigeration product, there
is a slight temperature variance at different
locations within the cabinet.
Suggestedbottlearrangement
forwine-full load(holds31wine
bottles)
Suggestedarrangementfor other
beverages-fullload(holds109
beverages)
6

Care and cleaning, ge.com
Cleaning the Outside
IMPORTANT: Unplug the beverage
center/wine chiller before cleaning.
Keep the outside clean. The cabinet
can be washed with mild soap and water.
Clean with a damp cloth. Never use
abrasive scouring powders.
Use a glass cleaner or mild soap and water
and a soft cloth to clean the glass door.
Do not use any abrasive powders.
Do not wipe the beverage center/wine
chiller with a soiled dishcloth or towel.
These ma_jleave a residue that can
erode the paint. Donot usescouting pads,
powdered cleaners, bleach or cleaners
containing bleach because these products
can scratch and weaken the paint finish.
Protect the paint finish. The finish
on the outside of the beverage center/
wine chiller is a high-quality, baked-on
paint finish. With proper care, it will stag
new-looking and rust-free for years. Apply
a coat of kitchen/appliance wax when the
wine chiller is new, and then at least twice
a year.
Cleaning the Inside
IMPORTANT: Unplug the beverage
center/wine chiller before cleaning.
Toclean the inner liner and racks, use
a warm water and baking soda solution-
about one tablespoon (15 ml) of baking
soda to a quart (1 liter) of water. This both
cleans and neutralizes odors. Clean with
a damp cloth.
The vinyl door gasket may be cleaned
with mild soap and water or a baking soda
solution.
Do not use detergents, scouring powders,
sprag cleaners or other harsh chemicals
to clean the interior.
To avoid water stains on the wood
shelves, clean up and drg ang liquid spills
immediatelg.
Wipe the control panel with a damp
cloth. Dry thoroughly. Do not use cleaning
sprays, large amounts of soap and water,
abrasives or sharp objects on the panel-
they can damage it. Some paper towels
can also scratch the control panel.
Defrosting
Defrost whenever frost on the inside
surfaces of the storage area becomes
!/8 " (3 mm) thick. Never use a heater
orang kind, scraper or sharp instrument
to remove frost as it mag damage
the beverage center/wine chiller.
To defrost, unplug the beverage center/
wine chiller. Remove the contents and wipe
inside surfaces and racks with a clean
towel. If frost does not come off easily,
allow the frost to melt somewhat and
wipe off.
After defrosting, make sure insidesurfaces
are dry; then return the contents to the
beverage center/wine chiller and set the
temperature control to the desired setting.
NOTE:The drain pan above the compressor
may be full following defrost. Check to
make sure no water spills when moving
the unit.

o
tt,
n
v A
o_
vz u_
_o
v
u I_
H
N
m
H
m
m
N
m
Ill
m
o
tt.
o
E
o
Care and cleaning.
In the Event of a Power Failure
If the power fails, open the door as
infrequently as possible to maintain
the temperature. A gradual rise in
temperature should not have any
adverse effect on the wine.
If it is extremely hot, you may want to
unload the wine from the beverage
center/wine chiller and move the wine
to a cooler location until power is restored.
The controls may maintain your
temperature settings when the power
has been restored. If your settings are not
correct, reset according to the Contro!
Settings section.
Preparing to Move
Unloadthe wine, then secure the racks by
taping them in place to prevent damage. Besure the beverage center!wine chiller stags in an upright position during the move.
Replacing the light bulb.
Screw
/
Unplug the beverage center/wine chiller.
Removeany beverages and shelvesas neededfor access.
The light bulb is located behind a light shield in the ceiling of the
beverage center/wine chiller near the back. To remove the light
shield, remove the screw on the right side of the light shield.
Pull down on the back of the light shield to release the two front tabs.
Unscrew the light bulb from the socket.
Replace with a 15 watt, 120 volt bulb. This type of bulb is available
at most hardware and automotive ports stores.
WARNING: Using abulb rated higherthan 15 watts mag
damage the electronic controls on the beverage center/wine chiller.
Reinstall the light shield.
Replace the top shelf and beverages.
Plug in the beverage center/wine chiller.
8

Reversing the Door. ge.com
Screw
Hinge cover _
PlugButton _ TT
I
Bottom
Hinge_
Leveling Leg
0 Unplug the beverage center/wine chiller.
Tape the door shut with masking tape to secure alignment.
Remove the top hinge cover by removing the screw.
Remove the 2 screws securing the top hinge to the frame.
Lean the beverage center backward to access the bottom hinge.
Remove the 2 screws securing the bottom hinge assembly to the
frame.
NOTE:If you lay the unit on its back, be sure to let it stand upright for
at least 2 hours before connecting to the power source; this will reduce
the possibility of a malfunction in the cooling system.
Remove the Plug Button from the top left side of the door.
O Install the Plug Button into the hinge hole on the right side.
Pressfirmly to secure.
O If the handle has been installed, remove it and install it
on the opposite side. Refer to Door Handle section for instructions.
0 Hold the door securely in place and install the bottom hinge
on the opposite side.
Install the top hinge and cover on the opposite side. Make sure
the door isaligned with the cabinet before tightening the screws.
Remove the tape. Open and close the door to check alignment with
the cabinet. If necessary, loosen the screws on the bottom hinge,
realign the door, and retighten the screws.
Plug in the beverage center/wine chiller.
NOTE:If you had to lay the unit on its back, be sure to let it stand
upright for at least 2 hours before connecting it to the power source;
this will reduce the possibility of a malfunction in the cooling system.
Set the temperature controls to the desired setting.

Before gou call for service...
Troubleshooting Tips
Save time and money! Review the charts on the following
pages first and you may not need to call for service.
Possible Causes What To Do
Appliance does not Appliance is unplugged. • Push the plug completelg into the outlet.
operate and the display The home circuit breaker • Replace fuse or reset the breaker.
is blank is tripped/the fuse is blown.
Vibration or rattling Appliance is on • See the Leveling Legs section.
(slight vibration an uneven surface.
is normal)
Motor operates for Normal when appliance • Wait 12 hours for the appliance to completely
long periods or cycles is first plugged in. cool down.
Often occurs when large • This is normal.
amounts of wine are pieced
in appliance.
Door left open. • Door is not self-closing. Always make sure that
the door is closed after opening.
Check to see if a bottle is holding door open.
Hot weather or frequent • This is normal.
door openings.
Temperature control set • SeeAbout the contro! and settings.
at the coldest setting.
Appliance is too close • See the Installation Guidelines section
to the wall. for the correct clearances.
Appliance too warm Normal when appliance • Wait 12 hours for the appliance to completely
is first plugged in. cool down.
Often occurs when large • This is normal.
amounts of wine are placed
in appliance.
Temperature control • SeeAbout the contro! and settings.
not set cold enough.
Warm weather or frequent • Set the temperature control one step colder.
door openings. SeeAbout the contro! and settings.
Appliance is too close • See the Installation Guidelines section
to the wall. for the correct clearances.
Door left open. • Door is not self-closing. Always make sure that
the door is closed after opening.
• Check to see if a bottle is holding door open.
• This is normal. If wine or beverages are too warm,
change the temperature setting to a lower temperature.
-- E
Appliance does not
operate, but the display
is lit and functioning
Setting is above room
temperature.
10

Possible Causes What To Do
Appliance has odor Interior needs cleaning. • See Care and cleaning.
Moisture forms on Not unusual during periods ,Wipe surface dry.
outside of appliance of high humidity.
Moisture collects inside Too frequent or too long
(in humid weather, door openings.
air carries moisture
into appliance when Wine bottles touching • Reposition bottles.
_enedl the back wall.
Frost forms on interior This is normal.
surfaces ofappfiance Door left open.
ge.com
See the Defrosting section.
• Excessivefrost may form if the door is left open.
See the Defrosting section.
• Door is not self-closing. Always make sure that
the door is closed after opening.
• Check to see if a bottle is holding door open.
Appliance too cold Temperature control • See About the contro! and settings.
is set too cold.
The room temperature where • For proper operation, the room temperature should
the appliance is located is be equal to or greater than the set temperature
too cold. of the appliance.
Temperature in the This is normal. • After you set the temperature, the display will go
display is not the back to showing the actual temperature.
temperature that
wasjust set.
Condensation on front Appliance is located • Wipe off the condensation with a clean, dry cloth.
of door in a high humiditg environment. • Locate the appliance in a lower humidity
environment.
Water on floor behind Door left open. • Door is not self-closing. Always make sure that
appliance the door is closed after opening.
Check to see if a bottle is holding door open.
Tilting unit when moving. • This is normal. The drain pan above the compressor
may be full following defrost. Check to make sure
no water spills when moving the unit.
11

C)
n
v A
o_
w m
vz u_
v
u
"O
L_
Q
C)
E
C)
L_
Notes.
12

GE Service Protection PIus'"
GE,a name recognized worldwide for quality and dependability together with Assurant Solutions, offers you
Service Protection PlusTM--comprehensive protection on your appliances.*
Benefits Include:
• Prompt, reliable service from GEAuthorized Servicers
• Convenient hours designed to suit your busy schedule
• Quality replacement parts
• The dependability of GE,a name recognized and trusted worldwide
• Ask about our interest-free payment plans
With Service Protection Plus gou cen expect:
• An extended service plan that limits unexpected repair bills
• Service coverage for most major brands
• Unlimited service calls for the length of your contract, or credit toward a replacement product
• Service coverage for covered operating parts and labor on appliances and home electronics that fail during normal single family
household use
• Your satisfaction isour goal. We strive to provide you with excellent service in a professional and timely manner.
Piece gour confidence in GEend cell us in the U.S.toll-free et 1.800.626.2224 for more informetion.
*Most brands covered up to 15 gears old in the continental U.S.
SPP is a trademark of General Electric Compang.
._ Cut here
Please place in envelope and mail to:
General Electric Company
Warranty Registration Department
P.O.Box 32150
Louisville, KY40232-2150
13

Consumer Product Ownership Registration
Dear Customer:
Thank gou for purchasing our product and thank gou for placing gour confidence in us.
We are proud to have gou as a customer!
Follow these three steps to protect gour new appliance investment:
Complete and mail
your Consumer
Product Ownership
Registration today,
Have the peace of
mind of knowing we
can contact gou in
the unlikely event of
a safetg modification.
After mailing the
registration below,
store this document
in a safe place. It
contains information
gou will need should
gou require service.
Our service number
is 800 GECARES
(800.832.2737).
Read gout Owner's
Manual carefullg.
It will help gou
operate your new
appliance properlg.
Model Number Serial Number
Important: If you did not get a registration card with your
product, detach and return the form below to
ensure that your product is registered, or register
online at ge.com. ,_ Cut here
Consumer Product Ownership Registration
Model Number
,,,,,,,,,,I I,
Serial Number
! ! ! ! ! !
Mr._i_ Ms.::i_ Mrs. ] Miss}
First I
Name I I I I I I I I I I LastName I I I I I I I I I I !
Street I
Address I I I ! I I I ! I I I I I I ! I I I I I !
Apt.#J II I I ! I I J E-mailAddress*
I
Citg I I I
Date Placed
lnUse I I
Month I
I I I I I I
Dagl I I Yearl
Zip
I ! I Statel I ] Code l I I ! !
Phone
Numberl I, I-I,, H ,, ,
GE Consumer & Industrial
Appliances
GeneralElectric Compang
Louisville,KY40225
ge.com
* Please provide gour e-mail address to receive, via e-mail, discounts, special offers and other important
communications from GEAppliances (GEA).
ill Check here if gou do not want to receive communications from GEA'scarefullg selected partners.
FAILURETOCOMPLETEAND RETURNTHISCARDDOESNOT DIMINISH YOURWARRANTYRIGHTS.
For information about GEA'sprivacg and data usage policg, go to ge.com and click on "Privacg Policg"
or call 800.626.2224.
14

Please place in envelope and mail to:
Veuillez mettre dans une enveloppe et envoyez _ :
OWHERSHJPREGISTRATIOH
P.O. BOX1780
MJSSISSAUGA,OHTARiO
L4Y4G1
(FORCAHADIAHCOHSUMERSOHLY)
15

Z
Z
For Canadian _:
Customers Ix:
Z
__1
Z
Pour les S
Consommateurs <_
Canadiens C)
Pleaseregisteryourproducttoenableustocontactyou Veuillezenregi_ervceeproduitariadenouspermet_ede
in the remote event a safety notice is issued for this product communiquer avec vous sijamais un avis de s6cudt6 concemant
and to allow for efficient communica_on under the terms ce produit 6ta_6mis et de communiquer facilement avec vous en
ofyour warranty, should the need arise, vertu de votre garar_e, sile besoin s'en fait ser@.
REGISTERON-LINE: www.geappliances.ca MAILTO: RO.BOX1780,MISSISSAUGA
ENREGISTREMENTSURINTERNETD,:www.electrameaagers.qe.ca POSTERD,:ONTARIO,L4Y461
[][] MISS/MLLE.MR'/M[][] Ms.MRS'/MME'FIRSTNAME/PRENOM LASTNAME/NOM
STREETNO/N° RUE STREETNAME/RUE
CITY/VILLE
AF. NO/APP./RR#
PROVINCE POSTALCODE/POSTAL
AREACODE/IND.REG.[TELEPHONE JE-MAIL
DIDYOUPURCHASEASERVICECONTRACTFORTHISAPPLIANCE? YES/OUI [] IFYES/SIOUI:EXPIRATION
Y/A M D/J
AVEZ-VOUSACHETEUN CONTRATDESERVICEPOURCETAPPAREIL? NO/NON []
NAME OFSELLINGDEALER/NOMDU MARCHAND MODEL /MODI_LE
SERIAL /SERIE
INSTALLATIONDATE/DATED'INSTALLATION
Y/A M D/J CORRESPONDENCE [] ENGLISH
CORRESPONDANCE [] FRAN?AIS
[] Ido notwishto receiveanypromotionaloffersregardingthisproduct.
[] Jenedesirepasrecevoird'offrespromotionnellesconcernantceproduit
16

Wine Chiller Warrants. igorcustomersintheunitedstotesJ
All warranty service provided by our Factory Service Centers,
or an authorized Customer Care®technician. To schedule
service, on-line, visit us at ge.com, or call 800.GE.CARES
(800.432.2737). Please have serial number and model number
available when calling for service.
Staple your receipt here.
Proof of the origina! purchase
date is needed to obtain service
under the warranty.
One Year
From thedate of the
origina!purchose
GE Will Replace:
Ang part ofthe wine chillerwhich fails due to a defect in materials or workmanship.
During this limited one-gear warranty, GEwill also provide,free of charge, all labor
and related serviceto replacethe defective part.
Service trips to gour home to teach gou how to use
the product.
Improper installation, deliverg or maintenance.
Failure of the product if it is abused, misused, or used for
other than the intended purpose or used commerdallg.
Loss of beverages due to spoilage.
Replacement of house fuses or resetting of circuit
breakers.
Damage caused after delivery.
Replacement of the light bulbs, if included, orwater filter
cartridge, if included, other than as noted above.
Damage to the product caused by accident, fire, floods
or acts of God.
Inddental or consequential damage caused by possible
defects with this appliance.
Product not accessible to provide required service.
EXCLUSION OF IMPLIED WARRANTIES--Your sole and exclusive remedy is product repair as provided
in this Limited Warranty. Any implied warranties, including the implied warranties of merchantability
or fitness for a particular purpose, are limited to one year or the shortest period allowed by law.
This warranty is extended to the original purchaser and an_l succeeding owner for products purchased
for home use within the USA. If the product is located in an area where service bg a GE Authorized Servicer
is not available, Sou mag be responsible for atrip charge or Sou mag be required to bring the product
to an Authorized GE Service location for service. In Alaska, the warrantbt excludes the cost of shipping
or service calls to sour home.
Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty
gives Sou specific legal rights, and Sou mag also have other rights which varg from state to state. To know
what btour legal rights are, consult btour local or state consumer affairs office or btour state's Attornebt General.
Warrantor: General Electric Company. Louisville, KY 40225
17

CUSTOMER WARRANTY
(for customers in Canada)
Your wine chiller is warranted to be free of defects in material and workmanship.
What is covered How Long Warranted
(From Date of Sale) Parts
Repair or Replace
at Habe's Option
Labour
Compressor GEProfile: Ten (!0) Years GEProfile:Ten (!0) Years GEProfile: Five (5)Years
GEand All Other GEand All Other GEand All Other
Brands: One (1)Year Brands: One (1)Year Brands: One (1)Year
Sealed Sgstem (including GEProfile: Five(5)Years GEProfile: Five (5)Years GEProfile: Five (5)Years
evaporator, condenser GEand All Other GEand All Other GEand All Other
tubing and refrigerant) Brands: One (1)Year Brands: One (1)Year Brands: One (1)Year
All Other Parts One (1)Year One (1)Year One (1)Year
t_
TERMS AND CONDITIONS:
Thiswarrants applies onlg for singlefamilg domestic
use in Canada when the Wine Chillerhas been properlg
installed according to the instructions supplied bg Mabe
and is connected to an adequate and proper utilitg
service.
Damage due to abuse, accident, commercial use, and
alteration or defacing of the serial plate cancels all
obligations of this warrants.
Service during this warrants period must be
performed bg an Authorized Mabe ServiceAgent.
Neither Mabe nor the Dealer isliable for ang claims or
damages resulting from failure of the Wine Chilleror
from service delags begond their reasonable control.
Toobtain warrants service, purchaser must present
the original Billof Sale.Components repairedor replaced
are warranted through the remainder of the original
warrants period onlg.
Thiswarrantg isextended to the original purchaser and
ang succeedingowner for products purchased for home
usewithin Canada. Inhome warrants servicewill be
provided in areaswhere it isavailableand deemed
reasonable bg Mabeto provide.
Thiswarrants isin addition to ang statutorg warrants.
WHAT IS NOT COVERED:
• Owner isresponsible to pag for service calls related
to product installation and/or teaching how to use
the product.
• Damage to finish must be reported within 48 hours
following the delivers of the appliance.
Damage to finish after delivers.
Improper installation-proper installation includes
adequate air circulation to the refrigeration sgstem,
adequate electrical, plumbing and other connecting
facilities.
Replacement of house fuses or resetting of circuit
breakers.
• Replacement of light bulbs.
• Damage to product caused bg accident, fire, floods
or acts of God.
• Lossof food due to spoilage.
Proper use and care of product as listed in
the owner's manual, proper setting of controls.
Product not accessible to provide required service.
WARRANTORISNOTRESPONSIBLEFOR
CONSEQUENTIALDAMAGES.
iEXCLUSIONOFIMPLIEDWARRANTIES-Yoursoleand exclusiveremedy is product repair as provided in this Limited Warranty. Any
implied warranties, including the implied warranties of merchantability or fitness for a particular purpose, arelimited to oneyear
or the shortest period allowed by law.
IM PORTANT
Keepthiswclrrontyand yourbillofsaleasproofoforiginalpurchaseand purchasedate.
Pleasehaveserialnumber and modelnumber availablewhen callingforservice.
Mabe Service isavailable coast to coast. If further help is
needed concerning this warrantg, contact:
Manager, Consumer Relations
Mabe Canada Inc., Consumer Service
1Factors Lane, Suite 310
Moncton, New Brunswick E1C9M3
1.800.561.:3344
Staple your receipt here.
Proof of the origina! purchase
date is needed to obtain service
under the warranty.
18

Instructions de s_curit_ ....... 20, 21
Instructions d'instollotion ........ 22
Mode d°emploi
Espace int@ieur ....................... 24
R@glages des commandes ............. 23
Entretien et nettoyoge ......... 25-27
Inversion de la porte ................... 27
Remplacement de I'ampoule ........... 26
Conseils de d_ponnoge ........ 28, 29
Soutien ou consommateur
Garantie ............................... 31
Soutien au consommateur ............. 32
Transcrivez ici les num6ros
de module et de s6rie :
N°de module
N°de s_rie
Ces num_ros setrouvent hI'int_rieur
du refroidisseur hvin hgauche.
19

J J
CONSEILSDESECURITEIMPORTANT&
LISEZTOUTESLESINSTRUCTIONSAVANTD'UTILISERVOTREAPPAREIL.
AVERTISSENENT!
Cat appareil doit _tre utilis_ uniquement aux fins pr_vues et d_crites dans ce manuel.
IVlESURESDE SdLCURITdL
Lors de I'utilisation de I'appareil, observez les pr4cautions 414mentaires, dont les suivantes '
_, Ce refroidisseur (_boissons et (_vin dolt @tre _, Eloignez lesdoigts des parties ok vous pouvez
iiiB,
correctement installS, conform@ment (_ces
instructions, avant qua vous ne I'utilisiez.
Nelaissez pas lesenfants grimper, s'asseoir, se
tenir debout ni se pendre aux clagettes de cat
appareil. IIspourraient I'endommager et
gravement se blesser.
N'entroposez pas et n'utilisez pas d'essence ou
autres vapeurs et liquides inflammables (_
proximit@de cat appareil ou de tout autre
appareil @lectrom@nager.
Avant de remplacer une ampoule grill_e,
le refroidisseur (_boissons et _ vin doit _tre
d_branch_ pour _viter tout contact avec un
filament sous-tension.(Une ampoule grill_e
peut se casser durant le remplacement).
facilement vous pincer; les espaces entre les
portes et entre les portes etles armoires sont
toujours _troits. Sogez prudent Iorsque vous
fermez les portes de I'appareil en pr@sence
des enfants.
iiiB,
D@branchezI'appareil avant de le nettoger
et de le r@parer.
REHARQUE: Nous vous recommandons
vivement de confier toute rdparation
8 un technician qua!iriS.
Neremisez pas et n'installez pas cat appareil
I'ext@ieur.
DANGER! RISQUE
D'UN ENFANT D'ENFERMEMENT
MISE AU REBUTAPPROPRIEEDE L'APPAREIL
Les enfants pris au pi@geou marts d'asphgxie sont
toujours d'actualit@. Lesappareils de r@frig_ration
abandonn_s ou mis au rebut sont toujours aussi
dangereux.., m@mesice n'est que pour quelques
jours. Si vous vous d_barrassez de votre ancien
appareil, veuillez suivre les directives ci-dessous
afin de pr@venirles accidents.
Avant de mettre au rebut votre appareil
de r_ffig_ration "
D@montezles portes.
Laissezles clagettes en place afin d'emp@cher
les enfants de grimper facilement _ I'int@ieur.
E-limination des CFC
Votre ancien r@frig@ateurcomporte
un syst@mede r@frig@ationqui utilise des CFC
(chlorofluorocarbures). Les CFCsont consid@@s
comme nocifs pour I'ozone stratosph@ique.
Si vous vous d_barrassez de votre ancien
r@frig@ateur,assurez-vous que le frigorig@ne avec
CFCest enlev@correctement par un technicien
qualifi& Si vous lib@rezintentionnellement
ce frigorig@ne avec CFC,vous pouvez @tresoumis
des amendes et _ I'emprisonement en vertu
de la Ioi sur I'environnement.
UTILISATIONDE CORDONS PROLONGATEURS
En raison des risques _ventuels sur la s_curit_ dans certaines conditions, nous d_conseillons
fortement I'utilisation d'un cordon prolongateur.
Cependant, sivous devez utiliser un cordon prolongateur, celui-ci dolt _tre absolument homologu_
par CSA,de tgpe trifilaire avec mise _ la terra, avec fiche et prise mises _ la terra, pour une alimentation
nominale de 15 amp@res(minimum) et de 120 volts.
20