GE LED 55 CC 1.4A ESRDL 1-10V 220-240 User manual

Page 1 of 6
Imagination at work
LED 55 CC 1.4A ESRDL 1-10V 220-240
Infusion System Power Supply
Doc Number: GE2024-9301
Power Supply Installation
Tighten the screws (x4) until the CAP goes down all the way and reaches the BASE.
BEFOR YOU BEGIN
Read these instruction completely and carefully
CAP
BA
S
E
CAP

Page 2 of 6
Imagination at work
Power Supply Installation
LED 55 CC 1.4A ESRDL 1-10V 220-240
PRIMARY SIDE – CHANNEL #1
OPTION – 1 OPTION – 2
WIRE TABLE
mm2CABLE
CHANNEL#1 – OPTION - 1 2X0.75mm2 – 2X1mm2 H05VVH2-F, SALCAVI-LSF
R30268
CHANNEL#1 – OPTION - 2 0.75mm2H03VV-F
CHANNEL #1
CHANNEL #2
CHANNEL #4
CHANNEL #3
PRI SIDE
TOP VIEW
SEC SIDE

Page 3 of 6
Imagination at work
Power Supply Installation
LED 55 CC 1.4A ESRDL 1-10V 220-240
PRIMARY SIDE – CHANNEL #2
OPTION – 1 OPTION – 2
WIRE TABLE
mm2CABLE
CHANNEL#2 – OPTION - 1 0.75mm2 LEONI-H03VVH2-F
CHANNEL#2 – OPTION - 2 0.75mm2-
CHANNEL #1
CHANNEL #2
CHANNEL #4
CHANNEL #3
PRI SIDE
TOP VIEW
SEC SIDE

Page 4 of 6
Imagination at work
Power Supply Installation
LED 55 CC 1.4A ESRDL 1-10V 220-240
SECONDARY SIDE – CHANNEL #3 & CHANNEL #4
CHANNEL #3 – LED & FAN CHANNEL #4 - DIM
WIRE TABLE
AWG
CHANNEL#3 LED 18 LED and FAN wires come as bundle-
inserted into a heat shrink sleeve.
FAN 18-24
CHANNEL#4 - DIM 18 -
CHANNEL #1
CHANNEL #2
CHA
N
NEL #
4
CHANNEL #3
PRI SIDE
TOP VIEW
SEC SIDE
TO FAN TO LED

Page 5 of 6
Imagination at work
LED 55 CC 1.4A ESRDL 1-10V 220-240 Dimensions
Power Supply Specifications
Performance Data Min Typical Max
Input Voltage (VAC) 198 220-240 264
Input Frequency (Hz) - 50/60 -
Input Current (A) - - 0.4
Output Voltage(VDC) LOAD 15 - 40
Output Current(ADC) 1.3 1.4 1.5
Output Power(W) - - 55
Environmental Operating Temperature
Range -20°C - +50°C
Environmental Humidity(non-condensing) - - 80%
Environmental Storage Temperature
Range -10°C - +70°C
Dimming 1-10 (VDC) 1 - 10
Output Current Dim (ADC) 0.1 - 1.5
Fan Output Voltage (VDC) - 12 -
Fan Output Power (W) - - 2

Page 6 of 6
Imagination at work
Safety Instructions:
1. Always disconnect power before installation and/or removal of the unit.
2. Install in accordance with national and local electrical codes.
3. Wire: for input use cable according to VDE standard 0285-5.
Safety Instructions
Safety Instructions
English,,Dutch,French,German,Hungarian,Italian,Norwegian,Russian,Spanish,Swedish,Polish,Arabic,Danish,
Belgian,Austrian and Finish versions of the installation instructions and safety information can be found at the
following location www.gelighting.com/LightingWeb/emea/resources/document-library
GE Lighting Solutions www.gelighting.com
GE Lighting Solutions, LLC is a subsidiary of the General Electric Company.
The GE brand and logo are trademarks of the General Electric Company.
© 2012 GE Lighting Solutions, LLC. Information provided is subject to change without notice. All values are design or typical values when measured under
laboratory conditions.