Genie TPC 8922 Series User manual

INSTRUCTION MANUAL
TPC 8922 Series
INFRARED DAY/ NIGHT CCD CAMERA
with WDR & OSD
IP66 RoHS

CAUTION:
TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT REMOVE COVER.
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
UNPACKING:
Unpack carefully. Electronic components can be damaged if improperly handled or dropped. If an
item appears to have been damaged in shipment, place it properly in its carton and notify the shipper.
1. Do not disassemble the camera.
Do not disassemble the camera unit as it is dangerous and may cause the damage to
the camera. Refer all servicing to qualified service personnel.
2. Handle the camera with care.
Be careful when handling the camera. In order to prevent any damages to the camera, do not drop or subject it
to strong shock or vibration.
3. Do not install the camera near electric or magnetic fields.
When installing the camera, keep away from TV sets, radio transmitters, magnets, electric motors, transformer,
audio speakers because the magnetic fields generated from these devices may distort the camera video image.
4. Cleaning
Use a soft lint free cloth to remove the dirt from the unit. Use lens tissue or a cotton tipped applicator with
ethanol to clean the camera lens.
5. Never face the camera directly toward the sun or other intense lighting.
Direct sunlight will damage the camera CCD.
IMPORTANT NOTE:
1.Read and follow Instructions: All operating and user instructions should be read and
followed before the unit is to be operated.
2.Electrical Connections: Only a qualified electrician should make the electrical connections.
Safety Warning
2
800mA ( Max. IR ‘s On)
25°or 45°
Infrared Beam Angle
Photo Diode Sensor ControlIR Light ON/OFF
6 piecesLED Quantity
60mIR Maximum Range (in ideal conditions)
3350 gmNet Weight
215 (L) x 120 (W) x 115 (H) mmCamera Space
Ivory Powder StoveCoating
Die-Cast Aluminum AlloyConstruction
Fully Cable ManagedMounting Bracket
4mmTemper Glass Thickness
IP66Ingress Protection Level
-40°C ~ +50°C
Environmental Operation Temp.
35°C (On) / 25°C (Off)
Blower Control
18°C (On) / 28°C (Off)
Heater Control
800mA ( Max. IR ‘s On)Power Consumption
AC90~240V (+/-10%) □AC24V (+/-10%) □
Power Input
TPC-8922/240TPC-8922/24Model

CAMERA SPECIFICATIONS
INFRARED DAY / NIGHT CAMERA with WDR & OSD MANAUL
3
Model Number TPC-8922/24 TPC-8922/240
Lens Varifocal Manual & Auto IRIS IR Lens 9-22mm
Lens Mount Board Mount Back Focus Adjustment
Image Device 1/3” Colour Sony Super HAD CCD Sensor
Signal System NTSC PAL
Picture Elements 768 (H) x 494 (V) 752 (H) x 582 (V)
Horizontal Resolution 560 TV L (DAY) / 600 TV L (NIGHT)
Rating Current 3.5A
Video Output VBS1 Vp-p at 75Ω/ITU 656
AGC Auto Gain 36dB
Colour/Mono Switching Synchronized with IR On/ Off
Frame Integration 30
Wide Dynamic Range 52dB
IR Accuracy No Focus Shift at Night
Auto Iris Lens Type AES /DC-IRIS
Shutter Control ALC1/ 60sec or Flicker-less 1/100sec
Backlight Compensation Auto Gain 36dB
White Balance ATW (2500°k-9000°k) / AWB
Digital Noise Reduction 3D, Auto
Gamma Correction 0.45/1.00
Minimum Illumination 0.001 LUX at F=1.0 (Video Output 30IRE, AGC on)
S/N Ratio 56dB (min)
Digital Zoom 2 X
Ambient Temperature (-25~50)°C / 30~90% RH

2. Temper Glass
3. IR LED : 4pcs/6pcs/7pcs super high power IR LED with refractor.
4. IR Board and IR Board Bracket
6. IR Control Board
5. Camera Board and Camera Board Bracket
PARTS DESCRIPTION
1. Lens Cap with Demisting Device
4

PARTS DESCRIPTION / INSTALLATION
How to Install Cables Through the Mounting Bracket
5
11. VR : To adjust Infrared LED activation level.
12. Thermostat Switch : Turns on at 35ﾟC and turns off at 25ﾟC for blower
13. Ground wire: Wired to the top cover.
7. Blower and Blower Bracket
9. Thermostat Switch : Turns on at 18ﾟC and turns off at 28ﾟC for defogging device
10. OSD setting button
14. RCA JACK Monitor output
15. BNC Monitor Out
8. Video Output BNC Female Connector
16. Live : White wire
17. Earth : Green wire
18. Neutral : Black wire

INSTALLATION
6

Lens Attributes:
1. Focus Ring
To set the focus, loosen the Focus lever and turn the ring toward <∞> or <N>
as necessary. When the desired focus is obtained re-tighten the focus ring lever.
2. Zoom Ring
Loosen the Zoom ring lever and adjust the viewing range by turning the ring towards
<W> for WIDE (Zoom out) or <T> for TELEPHOTO (Zoom In) as necessary.
Re-tighten the zoom ring lever when finished.
1
2
Zoom and Focus Adjustment
LENS / ZOOM AND FOCUS ADJUSTMENTS
Levers
7
TPC-8922/24: AC 24V(+/-10%) Power Input.
9-22 mm Auto IRIS and manual varifocal ED-IR lens.
Built in IR cut filter removable to get accurate colour.
ED lens to protect focus shift.
TPC-8922/240: AC 90~240V Power input.
9-222 mm or Auto IRIS and manual varifocal ED lens.
Built in IR cut filter removable to get accurate colour.
ED lens to protect focus shift.

OSD SETTING MANUAL:
To display OSD menu on screen, press and hold ENTER for at least 2 seconds
Press RETURN to exit OSD manual
Press UP, DOWN & ENTER to set up the features
IMAGE QUALITY 1.IRIS WDR
ALC
AES : FIX/AUTO
2. AGC/SENS AGC: AUTO/FIX
SENS: AUTO/FIX
3.ENHANCE H-L level
4. IR SETTING ON/OFF/EXT( default)
5. BACKLIGHT ON/OFF
48 areas selectable
6. WHITE BALANCE COLOUR: AUTO/ON/OFF
FUNCTION MENU 1. OSD MOTION: OFF/ON
ZOOM MAG: OFF/ON
2. MOTION DETECTION OFF/ON
48 areas, time, sense
selectable
3. DIGITAL ZOOM OFF/ON
4. H/V REVERSE H REVERSE: OFF/ON
V REVERSE: OFF/ON
5. FREEZE OFF/ON
6.CROSS LINE OFF/ON
7.MASK OFF/ON
8. POSI/NEGA POSI/NEGA
EXTRA SETTING 1.LANGUAGE English/Traditional Chinese/
Japanese
2.TITLE User- defined
3.PRIORITY VR PRIORITY: VR/OSD
OSD PRIORITY:
SWITCH/OSD
4.PRESET PRESET: ON/OFF

GENIE CCTV LTD.
CCTV House, City Park, Watchmead, Welwyn Garden City, Hertfordshire, AL7 1LT
Tel [phone] Fax [phone]
www.geniecctv.com Ver 1.01
GN-June 2010