Genie TPIR-607 Series User manual

TPIR-607 Series
INFRARED ILLUMINATOR ENCLOSURE
IP66 RoHS
INSTRUCTION MANUAL

CAUTION:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT REMOVE COVER.
THERE ARE NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING ONLY TO QUALIFIED SERVICE PERSONNEL.
UNPACKING:
Unpack carefully. Electronic components can be damaged if improperly handled or dropped. If an
item appears to have been damaged in shipment, pack it correctly in its carton and notify the shipper.
IMPORTANT NOTE:
1.Read and follow Instructions: All operating and user instructions should be read and
followed when installing this unit.
2.Electrical Connections: A suitably qualified person should make all electrical connections.
Model Number TPIR-607
LED Quantity 7 pieces
IR Light, Maximum Range 80 meters
Infrared Beam Angle 25°or 45 °
IR Light ON/OFF Photo Diode Sensor Control
Power Input AC24V (+/-10%) □AC90~240V (+/-10%) □
Current Rating 5.0A
Heater Control 18°C (On) / 28°C (Off)
Blower Control 35°C (On) / 25°C (Off)
Environmental Operation Temp. -40°C ~ +50°C
Protection Level IP66
Temper Glass Thickness 4mm
Mounting Bracket Fully-Cable Managed
Construction Die-Cast Aluminum Alloy
Coating Ivory Powder Stove
Dimension 425(L) x 160(W) x 165(H) mm
Camera Space 200(L) x 110(W) x 115(H) mm
Net Weight 5140gm
SAFETY WARNING / HOUSING SPECIFICATIONS
2

PART DESCRIPTION 3
2. Temper Glass
1. Lens Cap with Heater
3. IR LED
4. IR Board and IR Board Bracket
5. Universal IR Control Circuit Board: To control color/mono switching and IR on/off
synchronization.
6. Camera Bracket
7. Power Supply Unit : AC 24V or AC90~240V power input
Universal IR
Control Circuit
Board

PART DESCRIPTION / POWER CONNECTION
9. Thermostat Switch : Turn on at 28ﾟC and turn off at 18ﾟC
16. OUTPUT_2 : To power supply unit .
17. VR : To adjust the Infrared LED activation level.
8. Blower and Blower Bracket
10. Video Input BNC Male Connector : Connect to camera.
11. Video Out BNC Female Connector : Connect to monitor.
12. Terminal Board
13. Fuse Holder : With 250V/ 5.0A fuse .
14. AC IN Terminal block : AC 90~240V external power input.
15. OUTPUT_1 Spare Terminal Block : For AC 24V or AC 90~240V Camera use .
Note: When using two-cord power cable, please connect them to “Live” and “Neutral”
L E N
External Power Input Connection：
Live (Brown Wire)
Earth (Yellow/Green Wire)
Neutral (Blue Wire)
4
18. Thermostat Switch : Turn on at 35 ﾟC and turn off at 25 ﾟC for Blower.
19. Ground Wire: To top cover.
20. DC 12V Power-in Jack: For DC12V Camera use.
21. D/N trigger signal: To control the color/mono switching of D/N camera.
*IMPORTANT NOTE*
A: If IR trigger signal is on the high position
(+5Vdc), connect the Red and Black wire to D/N
trigger line +/- of camera
B: If IR trigger signal is on the Low position
(+0Vdc), connect the Orange and Black wire to
D/N trigger line +/- of camera.
Red wire:+5Vdc
Orange wire: 0Vdc
Black wire: Ground
1. If you use other D/N Cameras, please refer to the wiring diagram as below.

INSTALLATION
1
2
1. Loosen two screws on both sides of the camera bracket first.
2. Use provided screw to fix the camera on the camera bracket.
3
3. Adjust zoom, focus and iris of the lens on the camera.
Side View
5
Zoom Ring Focus Ring

INSTALLATION
Adjust position and direction
6
To external power source
Video Out BNC Female
Connector
Dimensions of Bracket Base
110.00mm
83.00mm
8.00mm
95.00mm

GENIE CCTV LTD.
CCTV House, City Park, Watchmead, Welwyn Garden City, Hertfordshire, AL7 1LT
Tel[phone] Fax[phone]
www.geniecctv.com