GeoVision GV-3D People Counter V2 User manual

Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
Quick Start Guide
GV-3D People Counter
V1.03
3DPCV103-QG-A-EN

© 2016 GeoVision, Inc. All rights reserved.
Under the copyright laws, this manual may not be copied, in whole or in part,
without the written consent of GeoVision.
Every effort has been made to ensure that the information in this manual is
accurate. GeoVision, Inc. makes no expressed or implied warranty of any kind
and assumes no responsibility for errors or omissions. No liability is assumed
for incidental or consequential damages arising from the use of the information
or products contained herein. Features and specifications are subject to
change without notice.
Note: No memory card slot or local storage function for Argentina.
GeoVision, Inc.
9F, No. 246, Sec. 1, Neihu Rd.,
Neihu District, Taipei, Taiwan
Tel: [phone]
Fax: [phone]
http://www.geovision.com.tw
Trademarks used in this manual: GeoVision, the GeoVision logo and GV
series products are trademarks of GeoVision, Inc. Windows and Windows XP
are registered trademarks of Microsoft Corporation.
January 2016

1
Contents
1. Introduction....................................................................................................................2
1.1 Packing List............................................................................................................................. 2
1.2 Options.................................................................................................................................... 2
2. Overview.........................................................................................................................4
2.1 Front View ............................................................................................................................... 4
2.2 Rear View................................................................................................................................ 5
2.3 The IR Remote Control ........................................................................................................... 6
3. Connection.....................................................................................................................7
4. Basic Configurations on OSD.......................................................................................9
4.1 Setting Up the Network ......................................................................................................... 10
4.2 Setting the ID, Password and Display Options ......................................................................11
5. Accessing the Web Interface ......................................................................................12
5.1 Setting the GV-3D People Counter....................................................................................... 13
5.2 Accessing Counting Results .................................................................................................15
6. Content Designer.........................................................................................................16
6.1 Creating a Screen Layout ..................................................................................................... 16
6.2 Exporting the Screen Layout to GV-3D People Counter ...................................................... 18
7. Upgrading the Firmware..............................................................................................19

2
1. Introduction
Welcome to the GV-3D People Counter Quick Start Guide. In the following sections, you will
learn about the basic installations and configurations of the GV-3D People Counter. For the
detailed user’s manual, see GV-3D People Counter User’s Manual.
1.1 Packing List
1. GV-3D People Counter × 1
2. IR remote control × 1
3. AC / DC adapter × 1 (12 V / 3 A, 36 W)
4. Power cord x 1
5. Software CD x 1
6. SD Card x 1
1.2 Options
Optional devices can expand your GV-3D People Counter’s capabilities and versatility.
Contact your dealer for more information.
Options for GV-3D People Counter
Options Description
Wall Mount Kit The Wall Mount Kit is used to mount the GV-3D People
Counter to the wall.
VESA Monitor Mount Kit The VESA Monitor Mount Kit is used to mount the GV-3D
People Counter to the back of a VESA monitor.
Asus Xtion Pro The Asus Xtion Pro is a motion sensor used to detect
the number of people who have walked through the
detection area. The operating temperature is from 0°C ~
40°C / 40°F ~ 104°F.
Asus Xtion Pro In-Ceiling
Mount
The In-Ceiling Mount is used to mount Asus Xtion Pro on
the ceiling.
USB Extension Cable
The 1.8 meters (6 feet) USB extension cable can extend
the distance between the Asus Xtion Pro and the GV-3D
People Counter.

3
GV-GPS Receiver
Receive the GPS signals for 3D People Counter
positioning.
GV-Web Report
Through a Web browser, the GV-Web Report keeps
track of and analyzes the people counting results and
shows the latitude and longitude from up to 1000 units of
GV-3D People Counters. Compatible version: For GPS
funtion, V2.2.6.0 or later. For the others, V2.2.3.0 or later.
Options for Asus Xtion Pro
Options Details
Asus Xtion Pro In-Ceiling
Mount
The In-Ceiling Mount is used to mount Asus Xtion Pro on
the ceiling.
Asus Xtion Pro Wall Mount
The Wall Mount is used for mounting Asus Xtion Pro on the
ceiling or on a door frame. The length and angle of the
mount can be adjusted to suit the installation site. The
length is adjustable from 188 ~ 290 mm (7.40 ~ 11.42 in).

4
2. Overview
2.1 Front View
123 4 5
No. Name Function
1 LED Indicators
The green LED indicates the Asus Xtion Pro is connected. The red
LED indicates the power is supplied.
2 USB Connect to an Asus Xtion Pro or an optional GV-GPS Receiver.
3 IR Built-in IR receiver to receive the IR signals from the IR remote control.
4 Default Reset the GV-3D People Counter to the default factory settings.
5 SD Card Slot Connect to a SD card for local storage and firmware upgrade.
Note:
1. If you want to connect both Asus Xtion Pro and GV-GPS Receiver to GV-3D People
Counter, use an additional powered USB hub to expand the USB port for connection.
2. Choose an USB hub with a power adapter to avoid insufficient supply of power.

5
2.2 Rear View
No. Name Function
1 Ethernet Connect to an Ethernet.
2 SPDIF Reserved (not functional).
3 HDMI Connect to an HDMI supported display device.
4 VGA Connect to a VGA monitor.
5 L/R Connect to a speaker.
6 Power OFF/ON Switch the power on or off.
7 DC 12V Connect to power by using the supplied power adapter.

6
2.3 The IR Remote Control
No. Name Function
1 Reboot Reboot the device.
2 Numbers / Alphabets
/ Punctuation Marks Enter the numbers, alphabets or punctuation marks.
3 Back Exit the Setup Menu and return to the counting page.
4 Direction Arrows Move up, down, right and left in the Setup Menu.
5 Rec Save the settings in the Setup Menu.
6 Menu Switch to the setup menu.
7 OK Enter the setup options in the Setup Menu.
Press Shift and 0~7 to switch to one of the 8 resolutions below.
Shift + 0 : VGA_640 x 480
Shift + 1 : VGA_1024 x 768
Shift + 2 : VGA_1280 x 768
Shift + 3 : VGA_1366 x 768
Shift + 4 : HDMI_480p
Shift + 5 : HDMI_720p
Shift + 6 : HDMI_1080i
Shift + 7 : HDMI_1080p
8 Shift
Note the resolution switch will cause the GV-3D People Counter
to automatically reboot.

7
3. Connection
Before connecting the GV-3D People Counter, read the following notes:
zGV-3D People Counter is compatible with the following firmware versions:
GV-3D People Counter V1.01: Asus Xtion Pro V5.3.26 and V5.7.9
GV-3D People Counter V1.02 or later: Asus Xtion Pro V5.7.9 and V5.8.22
zFor better results, avoid exposing the Asus Xtion Pro to direct sunlight or IR LED.
zYou can only connect GV-3D People Counter to one display device through HDMI or
VGA connector. The video signal will be unstable if multiple display devices are
connected.
1. Connect a display device to VGA video connector or HDMI connector for video and audio
alarm combined outputs.
2. Connect to a standard network cable.

8
3. If you use a VGA monitor, connect a speaker to L/R port for audio alarm.
4. Insert an SD card.
5. Connect the Asus Xtion Pro to the USB port of the GV-3D People Counter. The
recommended installation height for Asus Xtion Pro is between 1.8 – 5 meters.
6. Connect to power using the supplied power adapter.
7. Switch the Power button to ON.

9
4. Basic Configurations on OSD
After connecting the necessary devices and turning on the power, the window below appears.
The GV-3D People Counter starts counting people passing under Asus Xtion Pro.
To access the OSD (On-Screen Display) menu, press Menu on the remote control.
Note: By default, the video output is set to VGA with 1024 x 768 resolutions. If you have
connected an HDMI display device, use the IR remote control to press Shift + 0~7 to switch to
the corresponding resolution.

10
4.1 Setting Up the Network
In the OSD menu, select the Network tab to configure the IP address of the GV-3D People
Counter. If installed in a LAN with the DHCP server, the GV-3D People Counter will use a
dynamic IP address by default. If installed in a LAN without the DHCP server, the default IP
address 192.168.0.100 will be applied.
1. To assign a static IP address for the GV-3D People Counter, select Static IP and enter a
fixed IP address, subnet mask, DNS and gateway.
2. To use a dynamic IP assigned by the DHCP Server, select DHCP. Once connected, the
current IP address will be displayed next to Connected IP.
3. Press [REC] to save the settings. The GV-3D People Counter will reboot to apply the
settings.

11
4.2 Setting the ID, Password and Display Options
1. Select the Info tab.
2. Set the User Login ID and User Login Password to access the GV-3D People Counter.
3. In the Output field, select VGA or HDMI according to the video output of the display
monitor.
4. In the Resolution field, select one of the screen resolutions below.
HDMI at 60 Hz 480p 720p 1080i 1080p
VGA at 60 Hz 640 x 480 1024 x 768 1280 x 768 1366 x 768

12
5. Accessing the Web Interface
After installing the GV-3D People Counter on the network, you can access GV-Web Report
Lite to set up the Asus Xtion Pro and look up counting data. The GV-Web Report Lite is a Web
server built in the GV-3D People Counter.
System Requirements
To access GV-3D People Counter through Web browser, ensure your PC is in good network
connection, and use one of the following web browsers:
zMozilla Firefox V16.0.2 or later
zInternet Explorer V11.0.10240.16603 or later
Logging In
1. In your Web browser, type the IP address or the domain name of the GV-3D People
Counter in the Location / Address field.
2. Type the ID and password. The default ID and password are admin.
3. Type the characters shown in the image and click Login.

13
5.1 Setting the GV-3D People Counter
1. To set the GV-3D People Counter, click the Setup tab on the top.
2. Draw a box on the live view to mark the boundary of the detection zone. To change the
direction of the In / Out arrows, click the Change button after Direction Change on the
right.

14
3. For more precise counting results, specify the height of the Asus Xtion Pro in the Xtion
Device Height field and the minimum people height in the Minimum People Height
field. Click the Detail button to see an illustration of the detectable height range and the
dimensions of the detection area based on the height you specified.
4. To send People Counting data to other GV-Web Report Lite Server and / or GV-Web
Report, select Report to Server and type the IP address, port, name and password of
the GV-Web Report Lite or GV-Web Report.
For details, see Chapter 4 The Web Interface in the GV-3D People Counter User’s Manual.
Note: GV-3D People Counter is only compatible with GV-Web Report V2.2.3.0 or later.

15
5.2 Accessing Counting Results
After setting up the GV-3D People Counter to start collecting data, you can access the people
counts, tables and charts. Use one of the tabs below in GV-Web Report Lite to look up the
data.
zDevice: Displays the counted data and graphs from all connected GV-3D People
Counter. The data is updated every minute.
zGroup: You can group the connected GV-3D People Counter and see the data of the set
group.
zLog: Allows you to look up the data of a specified time period from the selected GV-3D
People Counter.
zQuery: Provides the daily, weekly, monthly and yearly people counting graphs and
tables.
For details, see Chapter 4 The Web Interface in the GV-3D People Counter User’s Manual.

16
6. Content Designer
Using the Content Designer, you can customize the screen layout for display monitor to show
the in counts, out counts, stay counts and the current time.
Follow the steps below to install the Content Designer:
1. Insert the Software CD to your computer. It runs automatically and a window pops up.
2. Select Install DirectX 9.0c and follow the on-screen instructions.
3. Select Install Microsoft .NET Framework 3.5 and follow the on-screen instructions.
4. Select GeoVision Content Designer and follow the on-screen instructions.
6.1 Creating a Screen Layout
1. To create a project, click File on the menu bar and select New Scenario.
2. Select GV-3D People Counter and a screen resolution. The screen resolution must
match the resolution you set for the display monitor.
Note: The following resolutions for HDMI and VGA video outputs are available:
HDMI at 60 Hz 480p 720p 1080i 1080p
VGA at 60 Hz 640 x 480 1024 x 768 1280 x 768 1366 x 768
For HDMI 480p, select 720 x 480; for HDMI 720p, select 1280 x 720; for HDMI 1080p and
1080i, select 1920 x 1080.

17
3. On the top-left corner, click the Background Image icon and click Browse to select
a picture in PNG, JPEG or BMP format to be the background image.
Note: The In Count, Out Count,Stay Count and Current Time will be shown on the
display monitor as numbers only. If you wish to label the counting data, you will need to add a
background picture with text added where the data will be shown. For example:

18
4. On the left side, click the In Count, Out Count,Stay Count and Current Time icons to
add these objects to the main screen.
5. You can adjust the size and position of the objects using the Size and Position fields in
the bottom-left corner or drag and drop the object boxes. To resize the box for Current
Time, double-click the object and select from a list of pre-defined resolutions.
6.2 Exporting the Screen Layout to GV-3D People Counter
1. To preview the created screen layout, click Preview on the main
screen.
2. To save the screen layout, click File and select Output Scenario.
3. Click to browse the location to save the screen layout. The screen layout will be
saved in a folder named 3DPeopleCounter.
4. In a SD card, create a folder named Scenario and copy the 3DPeopleCounter folder to
the Scenario folder.
5. Turn off the GV-3D People Counter, insert the SD card, and restart the GV-3D People
Counter to apply the new screen layout.