German pool GIC-BS2800WB User manual

使用說明書 OPERATING INSTRUCTIONS
GIC_BS2800WB-M-08(1)
使用說明書 OPERATING INSTRUCTIONS
在使用之前請詳細閱讀「使用說明書」及「保用條例」，並妥為保存。
Please read these instructions and warranty information carefully before use and keep them handy for future reference.
座檯式電磁爐
Free-Standing Induction Cooker
GIC-BS2800WB

目錄 TaBle of ConTenTS
注意事項 SAFETY CAUTION3
產品結構 PRODUCT STRUCTURE 3
操作說明 OPERATIONS 6
鍋具 COOKWARE 7
清潔及保養 CARE & MAINTENANCE 8
常見故障及處理 TROUBLE SHOOTING9
技術規格 TECHNICAL SPECIFICATIONS 10

I. 外型 Main Body
產品結構 PRoDUCT STRUCTURe
排氣口
Venting Outlet
微晶玻璃面板
Ceramic Glass Cook Top
操作面板
Control Panel
進風口
Air Inlet
電源線及插頭
Power Cord & Power Plug
P. 3
注意事項 SafeTY CaUTIon
!
-請單獨使用13A以上的插座，切勿使用萬用插座或與
其他電器共用插座
-請勿用水直接沖洗電磁爐，以免破壞電器絕緣性能
-請勿於排氣口及吸氣口插入鐵絲、金屬等物件，以免
發生觸電危險
-切勿讓鍋具猛烈撞擊陶瓷面板
-電磁爐水平放置後，側面及背面距離牆壁必須預留最
少10cm或以上，切勿堵塞出風口、將爐身鑲嵌或密封
-請勿將電磁爐放置在煤氣爐、煤油爐等熱源附近使用
-請勿將鐵片或其他鐵磁性材料直接放在陶瓷面板上加
熱，避免因高溫而產生灼傷危險
-空鍋具請勿加熱過久，以免發生危險，鍋具溫度過高
時，電磁爐會自動停止加熱
-切勿加熱罐頭等密封的東西，否則會因罐頭內氣體受
熱膨脹導致爆炸
-不使用電磁爐時，請將電源插頭由插座拔出
- Single 13A power jack must be used. Do not share power jack
with other appliances
- Do not apply water directly on to induction cooker
- Do not insert any wire or metal objects through air inlet or
venting outlet of the induction cooker
- Please avoid collision between cook top panel and cookware
- A distance of at least 10 cm between the wall and the sides of
induction cooker must be reserved for venting purposes
- Do not place or use induction cooker near any heat source
- Do not heat up any metal plate or other magnetic objects on
the cook top
- Do not heat empty cookware for an extended time.
Overheating of cookware will cause damages and injuries
- Do not heat un-opened cans on cook top. It may cause
explosion
- When induction cooker is not in use, unplug the power cord

III. 按鍵說明 Touch Keys
產品結構 PRoDUCT STRUCTURe
II. 控制面板 Control Panel
電源指示燈
Power Indicator
大爐頭(左) Large Hob (Left)
電源開關鍵
Power On/Off Switch
快速鍵
Turbo Key
火力/定時顯示窗
Power/Timer Display
溫度/火力轉換鍵
Temp./Power Switch
定時鍵
Timer Key
功能指示燈
Function Indicator
功能選擇鍵
Function Keys
控制鍵
Adjustment Keys
P. 4
“電源開關”鍵
於待機狀態下，按此鍵可啟動電磁爐，接著可按其中
一個“功能選擇”鍵選擇烹調功能以啟動運作。再按此
鍵一次便可轉回待機狀態。
“+ / - ”控制鍵
於“加熱狀態”下，按此兩鍵可設定火力(功率)大小。
於“定時狀態”下，按此兩鍵可設定預約關機時間及
預約開機時間。
“POWER ON / OFF” Key
Under standby mode, press this button to turn on cooker.
Select cooking function by pressing one of the “Function”
keys. Press this button again to return to standby mode.
“+ / -” Adjustment Keys
Under “Heating” mode, press to set power level;
Under “Timer Mode” (i.e. when “Timer” Indicator lights
up), press to adjust timer
1 2 3 4 5 6 7 8
200 W 400 W 800 W 1200 W 1600 W 2000 W 2200 W 2600 W
200 W 400 W 800 W 1000 W 1100 W 1200 W 1400 W 1600 W
1 2 3 4 5 6 7 8
80 ℃ 110 ℃ 140 ℃ 170 ℃ 200 ℃ 230 ℃ 250 ℃ 280 ℃
80 ℃ 110 ℃ 140 ℃ 170 ℃ 200 ℃ 230 ℃ 250 ℃ 280 ℃
段數
大爐頭功率
(約數)
小爐頭功率
(約數)
段數
大爐頭溫度
(約數)
小爐頭溫度
(約數)
功率參考 Power Level
溫度參考 Temperature Level
- + - +
- +

產品結構 PRoDUCT STRUCTURe
小爐頭(右) Small Hob (Right)
電源開關鍵
Power On/Off Switch
電源指示燈
Power Indicator
火力/定時顯示窗
Power/Timer Display
溫度/火力轉換鍵
Temp./Power Switch
定時鍵
Timer Key
預約鍵
Pre-set Key
功能選擇鍵
Function Keys
功能指示燈
Function Indicator
控制鍵
Adjustment Keys
P. 5
“定時關機”鍵
於加熱狀態下，按此鍵切換至“定時狀態”，顯示窗會
先顯示預設火力(大爐頭1600W；小爐頭1200W)，調校
火力後，再按此鍵一次以顯示定時時間(預設設定為
1分鐘)。“0:01”開始閃動，定時設定完成後(範圍︰
0-120分鐘)，再按此鍵確認設定。
“預約開機”鍵(小爐頭適用)
按此鍵切換至“預約狀態”，顯示窗會先顯示預設火力
(1200W)，調校火力後，再按此鍵一次以顯示預約開機
時間(預設為00:00分鐘，可調範圍︰1 min -24hr)。
設定完成後，再按此鍵確認設定。
“快速加熱”鍵 (大爐頭適用)
按1下﹕電磁爐設定在火力1600W運作
按2下﹕電磁爐設定在火力2800W運作
“TIMER” Key
Press TIMER key to switch to “Timer” mode. The digits
will be ashing to indicate power level (large hob 1600W;
small hob 1200W). After adjusting power level, press
TIMER key again. Timer clock “0:01” will be displayed
(default setting: 1 min). After adjusting timer, press
TIMER key once again to conrm.
“PRE-SET” Key (Small Hob Only)
Press PRE-SET key to switch to “Pre-set” mode. The digits
will be ashing to indicate power level (1200W). After
adjusting power level, press PRE-SET key again. “00:00”
will be displayed (adj. range: 1 min to 24 hr ). After
adjusting the desired starting time, press PRE-SET key
once again to conrm.
“TURBO” Key (Large Hob Only)
Press 1 time: cooker will operate at 1600W
Press 2 times: cooker will operate at 2800W
- +

操作說明 oPeRaTIonS
產品結構 PRoDUCT STRUCTURe
P. 6
1.將電源插頭插入插座，電磁爐發出“嗶”一聲，
表示電磁爐進入待機狀態。
2.將鍋具置於玻璃面板中央，按“開/關”鍵。
3.按鍵，設定火力段數。
註﹕若沒有放置鍋具或鍋具不合適，電磁爐不會
進行加熱，並會發出警號。
4.烹調完成後，按“開/關”鍵，使電磁爐轉回
待機狀態，然後將電源插頭從插座拔出。
1. Connect power. A “beep” sound will be heard. Induction
cooker enters “Standby” status.
2. Place cookware at the centre of cook top. Press
“ON / OFF” key.
3. Press to adjust power level.
Note: if there is no cookware or cookware not appropriate,
cooker will not start, and a buzzing sound is heard.
4. When nish, press “ON / OFF” key to switch to
“Standby” status, and then unplug power.
“功能選擇”鍵
大爐頭功能
煎炸
8段火力調校，電子屏幕會顯示相應功率。開始設定
為第5段火力(1600W)
炒菜
8段火力調校，電子屏幕會顯示相應功率。開始設定
為第5段火力(1600W)
按1下﹕火力1600W
按2下﹕火力2600W
小爐頭功能
蒸煮
8段火力調校，電子屏幕會顯示相應功率。開始設定
為第4段火力(1000W)
溫奶
低火力(200W)加熱。完成加熱後電磁爐會發出聲響，
並轉為保溫狀態，移鍋即自動關機
燒烤
8段溫度調校，電子屏幕會顯示相應溫度。開始設定
為第5段溫度(200℃)
煲湯
8段火力調校，電子屏幕會顯示相應功率。開始設定
為第7段火力(1400W)
“FUNCTION” Keys
Large Hob Functions
DEEP FRY
8-level power control; default – level 5 (1600W)
STIR-FRY
8-level power control; default – level 5 (1600W)
Press 1 time: power level set to 1600W
Press 2 times: power level set to 2600W
Small Hob Functions
STEAM / BOIL
8-level power control; default – level 4 (1000W)
WARM MILK
Automatic low-power heating (200W by default).
When heating is over, a “beep” sound will be heard,
and induction cooker with switch to “Keep Warm”
mode until cookware is removed from cook top
GRILL
8-level temperature control; default – level 5 (200°C)
SOUP
8-level power control; default – level 7 (1400W)
- +
- +

適用的各類鍋具 Appropriate
不適用的各類鍋具 Not Appropriate
鍋具 CooKWaRe
請使用德國寶電磁爐專用或認可之鍋具，儘量不要選用其他代替品，以免性能受影響。
Please use only German Pool authorized cookware or cookware recommended by us. Any unauthorized cookware may affect
induction cooker’s heating capacity and quality.
材質 : 鐵、鑄鐵或導磁不銹鋼。
Material: Metal, ferromagnetic stainless steel or cast iron.
形狀 : 底部直徑12 cm以上之平底鍋。鍋具底部直徑不宜超過25 cm，鍋具加上食物的重量不宜超過6 kg。
Shape: Flat bottom with a diameter of 12 cm or more. Cookware bottom diameter should not exceed 25 cm
and must not weight over 6 kg (with food).
材質 : 非鐵質金屬、陶瓷、玻璃以及鋁或銅為底的鍋具。
Material: Non-metallic, non-ferromagnetic, ceramic, glass, aluminum or brass.
形狀 : 底部凹凸差距過大的，底部直徑小於8 cm。
Shape: Bottom not at or too bumpy, or bottom diameter smaller than 8 cm.
磁性不銹綱水壺
Ferromagnetic
Stainless Steel
Cooking Pot
鋁製水壺
Aluminum Water Pot
鐵製炸鍋
Ferromagnetic
Stainless Steel
Water Pot
耐熱玻璃鍋
Glass Pot
磁性不銹鋼鍋
Metal Frying Pan
陶瓷鍋
Ceramic Pot
鐵製彩色鍋
Metal Saucepan
底部凹凸不平
Pot With Non-Flat/
Curved Bottom
磁性鐵製琺瑯壺
Ferromagnetic
Metal Water Pot
鍋底附腳
Pot With Bumpers
鐵板/鑄鍋
Cast Iron Grilling
Pan
底部直徑過小
Pot Bottom Too
Small
P. 7

清潔及保養 CaRe & MaInTenanCe
P. 8
-清潔前必須先拔下電源插頭
-任何污垢必須即時清理
-必須待爐面完全冷卻才進行清潔
-清潔面板時，先以扭乾的濕布擦拭；若仍未能除掉污
漬，可用中性去污粉或洗潔精擦拭，然後再用濕布擦
拭即可
-清潔電磁爐機身時，先用柔軟濕布擦拭﹔若有油污難
以清除時，用中性洗潔精擦拭後再用濕布擦拭乾淨
-切勿用水直接沖洗或將機身浸入水中清洗
-切勿使用堅硬之刷子刷洗爐面
-切勿使用有機溶劑或苯等化學藥品擦拭電磁爐
- Power plug must be disconnected before cleaning
- Any stain or deposit on the cook top surface must be cleaned
off immediately before re-using
- Cleaning must be done when cook top surface has completely
cooled down
- If stain is minimal, wipe off with a dry cloth. If stain remains,
clean cook top with a moist sponge (soaked with mild soap)
and then wipe again with a clean cloth
- To clean the body of induction cooker, wipe with a soft clean
cloth. If stain remains, clean with a moist sponge (soaked with
mild soap) and then wipe with a clean cloth
- Do not immerse induction cooker into water
- Do not clean cook top with any rough cloth or abrasive tool
- Do not use organic solvents or any cleaning products that
contain chemicals such as Benzene

常見故障及處理 TRoUBle SHooTInG
使用中如發現電磁爐操作上有問題，在送回本公司維修前請先依照下表進行檢查﹕
When you run into any problem operating this product, use the table below to troubleshoot the problem.
If the problem persists, contact our Repair & Customer Service Centre.
故障現象
接通電源，按“開/關”鍵，電磁爐
無反應。
Power is connected, but the induction
cooker does not respond when the
On/Off button is pressed.
峰鳴器斷續鳴響且鍋具不加熱。
Buzzer beeps continuously and pan is
not heated.
在正常運作時停止加熱。
Induction cooker stops heating during
normal operations.
保溫失控。
Temperature uctuates.
•是否停電?
Is there a power shortage in
your area?
•府上的自動開關或保險絲是否發
生短路?
Is there a short circuit in the
power source of your home?
•插頭是否脫落或接觸不良?
Is the power plug too loose or not
connected well?
•鍋具不適應?
Is the pan not suitable for induction
cooking?
•鍋具位置不合適?
Is the pan positioned properly?
•是否空鍋或溫度過高?
Is the pan empty or cooking
temperature too high?
•吸氣口或排氣口是否堵塞?
Are the air inlet and outlet being
blocked?
•室溫是否太高?
Is the surrounding temperature
too high?
•鍋底是否凹凸不平?
Is pan bottom not at?
檢查要點
使用電磁爐適用之鍋具。
Use an appropriate pan.
將鍋具放置在電磁爐面板中心。
Position the pan in the centre of cook top.
防止乾燒，降溫後自動繼續。
Avoid operating cooker with an empty pan.
Let cooker cool down before switching it
on again.
待機件冷卻後才使用，並注意保持內部
通風。
Remove obstruction from the vent. Let
induction cooker cool down and try again.
室溫降低後才使用。
Try again after the room cools down.
更換平底鍋具後使用。
Replace pan with a at-bottomed one.
電源恢復後再使用。
Try again after power supply resumes.
檢查短路原因，排險後才使用。
Find out the cause of short circuit and
eliminate it before switching on the cooker
again.
插牢或更換插孔後使用。
Re-connect the plug or replace the power
jack.
處理方法
*以上為常見故障的判斷與檢查，只供用戶作參考之用。
Above table enlists the most common problems regarding the operations of the product and their possible causes as well as suggested solutions. It is strictly for users’
reference only.
*如遇故障切勿自行修理，避免發生危險及對機件造成損害，請立即找專業技術人員或聯絡本公司作出適當維修。
Should there be any product malfunction or breakdown, DO NOT repair it yourself. Contact our Repair & Customer Service Centre or consult a licensed technician
immediately.
*E3及E4並不屬於機器故障，待電壓恢復後（187V—250V）即可使用。
E3 & E4 are not product errors. Operation can be resumed when power voltage returns to normal rating (187V - 250V).
故障代碼
Code
E0
E3*
E4*
E5
E6
故障說明
Error
無鍋具/鍋具不合適
No cookware / Inappropriate cookware
電壓過高
Voltage over-loaded
電壓過低
Voltage under-loaded
爐面感應器斷路
Open circuit of cook top sensor
爐面感應器短路
Short circuit of cook top sensor
故障說明
Error
爐面過熱
Cook top overheat
機內溫度感應器短路
Short circuit of internal temperature sensor
機內溫度感應器斷路
Open circuit of internal temperature sensor
機內溫度過高
Internal overheat
故障代碼
Code
E7
E8
E9
EA
P. 9

技術規格 TeCHnICal SPeCIfICaTIonS
產品規格及設計如有變更，恕不另行通知。一切均以產品實物作準。
Specications are subject to change without prior notice.
P. 10
型號Model
電壓Voltage
頻率Frequency
功率Power
電流Electric Current
爐頭數目Number of Hobs
顏色Colour
尺寸Dimensions
淨重Net Weight
總重Gross Weight
GIC-BS2800WB
220 V
50 Hz
2.8 kW
12.8 A
2
Black
(H) 70 mm (W) 660 mm (D) 355 mm
7.7 kg
8.4 kg