Gianni Industries ML-210 User manual

Copyright © All Rights Reserved. P-MU-ML-210 Ver. C Publish: 2010.12.02 4-1
ML-210
ML-210-SW
Operating Voltage» ML-210: 12 or 24VDC
ML-210-SW: 12~24VDC/AC
Voltage Tolerance» ±10%
Current Draw» ML-210: 280mA/12VDC; 140mA/24VDC
ML-210-SW: 210mA/12VDC; 150mA/24VDC
Version Changeable» Fail-safe or Fail-secure
Operating Temperature» -10~45°C
Humidity» 0~95% non-condensing
Lock bolt sensor switch output» SPDT rated 3A/125VAC
Solenoid testing» Tested to 1,000,000!cycles
Net Weight» ML-210: 540g / ML-210-SW: 555g
Just applicable to vertical installation Double swing door
Unit:mm
Double Swing Doors
Electromechanical Lock
Installation Instruction
Specifications
Fixing Lug
Allen wrench (1.6mm)
Nib
Lock bolt
Strike Plate
Packing Contents Template
Outswing Inswing
Version Changeable:
Take out the Screw 1 , release the screw 2 , move the
position and then tighten both screws.
“Fail-Safe”
(Power to Lock) “Fail-Secure” (Power to Open)
Caution:
Do not completely remove screw 2 (as marked in the figure)
as the interior solenoid might fall off.
ø5.0
ø5.0
4-R2
25
210
33
253
30
38
150
206
22
Butt Splice (IDC) Connector
Using crimper or pliers and pressing the header of
connector down to even position.
Cut on dotted line
Alignment CL
4-4
ø5.0
ø5.0
25
210
ø5.0
150
28
30
28
ø5.0
Unit:mm
Installation Instructions
Door Loop
(Optional)
The door loop protects the wiring
from damage at the door hinge.
Attention! Please ensure that the
template is the correct way up
Alignment CL
F
r
a
m
e
D
oor
Le
af
ø5.0
ø5.0
D
o
o
r
L
e
a
f
Cut out mortise holes for the lock
body and strike plate and drill Tighten the fixing lugs with
Doo
r Leaf
Connect power cable to the lock
and test before screwing to the Affix the strike plate.
Copyright © All Rights Reserved. P-MU-ML-210 Ver. C Publish: 2010.12.02
Do
o
r
F
ra
m
e
D
o
o
r
le
af
Do
o
rF
ram
e
D
o
o
r
L
e
af
Align the center line (CL) of the lock
bodytemplate with the CLofthe door
leaf. Ensure the CL of the strike plate
templatematchesthelockbodyCLas
closely as possible. holes according to the templates. screws.
door leaf.

4-2
12VDC Power supply12VDC Power supply
Wiring Diagram
ML-210 Voltage Input: 12 or 24VDC Lock bolt sensor status output
For 12VDC operation, the solenoid input wires
should be connected in parallel as shown.
Black
Red
Black
Red Varistor
Access Control Device
N.C. contact
(Power input is polarity free)
Yellow
Green
Blue
“Fail-Safe”
(Power to Lock)
“Fail-Secure”
(Power to Open)
Yellow
Green
Blue
Access Control Device
N.O. contact
Varistor
Black
Red
Black
Red (Power input is polarity free)
For 24VDC operation, the solenoid input wires
should be connected in series as shown.
12VDC Power supply
Black
Red
Black
Red Varistor
(Power input is polarity free)
24VDC Power supply
“Fail-Safe”
(Power to Lock)
Yellow
Green
Blue
Copyright © All Rights Reserved. P-MU-ML-210 Ver. C Publish: 2010.12.02
Access Control Device
N.O. contact
Black
Red
Black
Red Varistor
(Power input is polarity free)
24VDC Power supply
Yellow
Green
Blue
“Fail-Secure”
(Power to Open)
Access Control Device
N.O. contact
4-3
Wiring Diagram
ML-210-SW Voltage Input: 12~24VDC/AC Lock bolt sensor status output
For the 12~24VDC/AC operation only
NOTE: The varistor (or diode) must be connected across the terminals as shown. This protects the electromechanical lock
from spikes and surges.
Copyright © All Rights Reserved. P-MU-ML-210 Ver. C Publish: 2010.12.02
12~24VDC/AC Power supply
“Fail-Safe”
(Power to Lock)
Red
Red Varistor
(Power input is polarity free)
Yellow
Green
Blue
Access Control Device
N.O. contact
Red
Red Varistor
12~24VDC/AC Power supply
(Power input is polarity free) “Fail-Secure”
(Power to Open)
Yellow
Green
Blue
Access Control Device
N.O. contact