Gilson Pipetman Classic Series User manual

User’s Guide
EN
CLASSIC

TABLE OF CONTENTS
2TABLE OF CONTENTS | PIPETMAN® CLASSIC
TABLE OF CONTENTS
INTRODUCTION | 3
Parts Checklist | 3
GLP Compliant | 3
Description | 4
Specifications | 4
SETTING THE VOLUME | 6
PIPETTING | 7
Fitting the Tips | 7
Pre-Rinse the Tips | 8
Guidelines for Good Pipetting | 9
ACCESSORIES | 11
TROUBLESHOOTING | 12
Troubleshooting Table | 12
Leak Test | 14
MAINTENANCE | 15
Changing the Tip Ejector | 15
Changing the Tip Holder – No Tools Required | 17
Servicing the Piston Assembly | 17
Cleaning and Decontamination | 18
SPARE PARTS | 21
P2 (F144801) and P10(F144802) | 22
P20 (F123600) and P100(F123615) | 22
P200 (F123601) and P1000(F123602) | 22
P5000 (F123603) and P10mL(F161201) | 22
WARRANTY | 24

INTRODUCTION
3
PIPETMAN® CLASSIC |USER’S GUIDE
TABLE OF CONTENTS | PIPETMAN® CLASSIC
Chapter 1
INTRODUCTION
PIPETMAN® Classic, the pipetting standard, is a
fully adjustable, air-displacement pipette that is
used with disposable tips. The PIPETMAN Classic
offers a large range of accurate and precise
pipettes.
Eight single channel models cover a volume range
from 0.2 µL to 10mL for many applications:
●P2 and P10: measurement and transfer of
microliter volumes, DNA sequencing, and
enzyme assays.
●P20, P100, P200, and P1000: measurement
and transfer of general aqueous solutions,
acids, and bases.
●P5000 and P10mL: measurement and
transfer of large volumes.
Parts Checklist
After unpacking the pipette, verify that
the following items were included and are
undamaged:
●PIPETMAN Classic
●PIPETMAN Classic Quick Guide
●P2 and P10 dual-position adapter
●Safety bag
●Certificate of Conformity (including barcode
sticker)
GLP Compliant
The serial number is engraved
on the body of the pipette. It
provides unique identification
of your pipette and the date of
manufacture.
Ex:QG10369
The barcode on the box and the
Certificate of Conformity provide
traceability of your pipette.
Figure 1
Serial number
location
NOTE
The updated line of PIPETMAN Classic
is identified with an underlined serial
number starting from QG.
Serial Number

INTRODUCTION
4INTRODUCTION | PIPETMAN® CLASSIC
Description
Specifications
PIPETMAN Classic is a high quality pipette that
offers excellent accuracy and precision. The data
provided in the Maximum Permissible Errors table
were obtained using PIPETMAN® DIAMOND Tips.
These values are guaranteed only when genuine
PIPETMAN® DIAMOND Tips are used.
Each pipette is inspected and validated by
qualified technicians in accordance with the
Gilson Quality System. Gilson declares that
its manufactured pipettes comply with the
requirements of the ISO8655 standard by type
testing. The adjustment is carried out under
strictly defined and monitored conditions
(ISO8655-6).
Thumbwheel
Body or
handle
Tip holder
PIPETMAN®
DIAMOND Tip
Connecting
nut
Color-coded
push button
Tip ejector
button
Tip ejector*
Figure 2
PIPETMAN® Classic single channel model
Clip tip ejector
*Plastic tip ejector available as an accessory. Refer to ACCESSORIES on page 11.

INTRODUCTION
5
PIPETMAN® CLASSIC |USER’S GUIDEINTRODUCTION | PIPETMAN® CLASSIC
Maximum Permissible Errors
The data provided in the following tables
conform to the ISO8655-2 standard. With
a precise pipetting technique (refer to
Guidelines for Good Pipetting on page 9), the
P2 model may be used to aspirate volumes as low
as 0.1 µL and the P10 model as low as 0.5 µL.
Figure 2
PIPETMAN® Classic single channel model
VOLUME
(µL)
GILSON ISO 8655
SYSTEMATIC
ERROR (µL)
RANDOM
ERROR (µL)
SYSTEMATIC
ERROR (µL)
RANDOM
ERROR (µL)
P2 (P/NF144801) WITH D10 OR DL10 TIPS
0.2 ± 0.024 ≤0.012 ± 0.08 ≤0.04
0.5 ± 0.025 ≤0.012 ± 0.08 ≤0.04
1± 0.025 ≤0.012 ± 0.08 ≤0.04
2± 0.030 ≤0.014 ± 0.08 ≤0.04
P10 (P/NF144802) WITH D10 OR DL10 TIPS
1± 0.025 ≤0.012 ± 0.12 ≤0.08
5± 0.075 ≤0.030 ± 0.12 ≤0.08
10 ± 0.100 ≤0.040 ± 0.12 ≤0.08
P20 (P/NF123600) WITH D200 TIPS
2± 0.10 ≤0.030 ± 0.2 ≤0.1
5± 0.10 ≤0.040 ± 0.2 ≤0.1
10 ± 0.10 ≤0.050 ± 0.2 ≤0.1
20 ± 0.20 ≤0.060 ± 0.2 ≤0.1
P100 (P/NF123615) WITH D200 TIPS
10 ± 0.35 ≤0.10 ± 0.8 ≤0.3
50 ± 0.40 ≤0.12 ± 0.8 ≤0.3
100 ± 0.80 ≤0.15 ± 0.8 ≤0.3
P200 (P/NF123601) WITH D200 TIPS
20 ± 0.50 ≤0.20 ± 1.6 ≤0.6
100 ± 0.80 ≤0.25 ± 1.6 ≤0.6
200 ± 1.60 ≤0.30 ± 1.6 ≤0.6
P1000 (P/NF123602) WITH D1000 TIPS
100 ± 3.0 ≤0.6 ± 8.0 ≤3.0
500 ± 4.0 ≤1.0 ± 8.0 ≤3.0
1000 ± 8.0 ≤1.5 ± 8.0 ≤3.0
P5000* (P/NF123603) WITH D5000 TIPS
500 ± 12 ≤3 ± 40 ≤15.0
2500 ± 15 ≤5 ± 40 ≤15.0
5000 ± 30 ≤8 ± 40 ≤15.0
P10mL* (P/NF161201) WITH D10mL TIPS
1000 ± 30 ≤6 ± 60 ≤30.0
2000 ± 30 ≤6 ± 60 ≤30.0
5000 ± 40 ≤10 ± 60 ≤30.0
10000 ± 60 ≤16 ± 60 ≤30.0
*P5000 and P10mL do not have tip ejectors.

SETTING THE VOLUME
6SETTING THE VOLUME | PIPETMAN® CLASSIC
Chapter 2
SETTING THE VOLUME
The volume of liquid to be
aspirated is set using the
volumeter. The dials are
colored either black or
red to indicate the
position of the decimal
point, depending on the
model (refer to Figure 3).
The volume is set by
turning the thumbwheel
or the push button. The
push button makes it
easier and faster to set
volumes, especially
when wearing gloves.
The thumbwheel may be
turned to slowly reach the
required setting.
MODEL COLOR OF VOLUMETERNUMBERS
BLACK RED INCREMENT
P2 µL 0.01 µL 0.002 µL
P10–P20 µL 0.1 µL 0.02 µL
P100–P200 µL —0.2 µL
P1000–P5000 0.01 mL mL 0.002 mL
P10mL mL 0.1 mL 0.02 mL
To obtain maximum accuracy when setting the
volume:
●When decreasing
the volume
setting, slowly
reach the required
setting, making
sure to not pass
the setting.
●When increasing
the volume
setting, pass the
required value by
1/3 of a turn and then
slowly decrease to
reach the volume,
making sure to not
pass the setting.
Figure 3
Dial colors by model
Color-coded
push button
Thumbwheel
Figure 4
Location of
push button and
thumbwheel

PIPETTING
7
PIPETMAN® CLASSIC |USER’S GUIDESETTING THE VOLUME | PIPETMAN® CLASSIC
Chapter 3
PIPETTING
While many brands of tips can be used with
the PIPETMAN® Classic, it is recommended to
use PIPETMAN® DIAMOND Tips for optimum
performance. These tips are made from pure
polypropylene. Plastic tips are for a single
application—they should not be cleaned for
reuse.
Fitting the Tips
To fit a new PIPETMAN DIAMOND Tip, push
the tip holder into the tip using a slight twisting
motion to ensure a firm, airtight seal.
Fitting the Tips on P2 and P10 Models
NOTE
For the P2 and P10 models, a dual-
position adapter (plastic) is required
to fit DL10 tips (longtips) or D10 tips
(short tips). The metallic rod of the tip
ejector is shaped so the adapter may
be clipped to it in either position.
P2 and P10 models are delivered with the
adapter in place, positioned in the longer slot,
and ready to use DL10tips.
When D10 tips are used, the
adapter must be repositioned
in the shorter slot as follows:
1. Pull the adapter down from
the metallic rod.
2. Turn the adapter 180°.
3. Refit the adapter so the
end of the metallic rod
engages the shorter slot of
the adapter.
Short
tips
Long
tips
Figure 5
Dual-position
adapter for P2
and P10
NOTE
Dual-position
adapter is
autoclavable.

PIPETTING
8PIPETTING | PIPETMAN® CLASSIC
An autoclavable tip ejector extension
can be ordered as an accessory for
P2 and P10 equipped with a plastic tip
ejector (part number F107027; refer to
ACCESSORIES on page 11).
To fit a tip ejector extension:
1. Slide the extension over the tip
holder.
2. Push the extension firmly onto
the end of the tip ejector until it
clicks into place.
To remove a tip ejector extension:
1. Gently twist the extension.
2. Pull it away from the pipette.
Pre-Rinse the Tips
Some liquids (e.g., protein-containing solutions
and organic solvents) can leave a film of liquid
on the inside wall of the tip. Pre-rinse the tip to
minimize any errors that may be related to this
phenomenon.
Pre-rinsing consists of aspirating the first volume
of liquid and then dispensing it back to waste.
Subsequent volumes you pipette will have levels
of accuracy and precision within specifications.
Aspirate
1. Press the push button to the first stop (this
corresponds to the set volume of liquid).
2. Hold the pipette vertically and
immerse the tip in the liquid (refer to
Guidelines for Good Pipetting on page 9).
3. Release the push button slowly and smoothly
(to the top position) to aspirate the set
volume of liquid.
4. Wait one second. The time depends on the
model (refer to the table). Then, withdraw
the pipette tip from the liquid. You may wipe
any droplets away from the outside of the tip
using a medical wipe; however, if you do so,
take care to avoid touching the tip’s orifice.

PIPETTING
9
PIPETMAN® CLASSIC |USER’S GUIDEPIPETTING | PIPETMAN® CLASSIC
Dispense
1. Place the end of the tip against the inside wall of
the recipient vessel at an angle of 10° to 40°.
2. Press the push button slowly and smoothly
to the first stop.
3. Wait for at least one second, then press the
push button to the second stop to expel
any residual liquid from the tip. Keep the
push button pressed fully down and (while
removing the pipette) draw the tip along the
inside surface of the vessel.
4. Release the push button smoothly. Eject
the tip by pressing firmly on the tip of the
ejector button.
Rest position
First stop
Second stop
Figure 6
Pipetting motion - aspirate and dispense
Guidelines for Good Pipetting
●Make sure you operate the push button
slowly and smoothly.
●When aspirating, keep the tip at a constant
depth below the surface of the liquid (refer
to the table).
MODEL IMMERSION DEPTH
(MILLIMETERS)
WAIT TIME
(SECONDS)
P2 1 1
P10 1 1
P20 2–3 1
P100 2–4 1
P200 2–4 1
P1000 2–4 2–3
P5000 3–6 4–5
P10mL 5–7 4–5
●Change the tip before aspirating a different
liquid, sample, or reagent.
●Change the tip if a droplet remains at the end of
the tip from the previous pipetting operation.

PIPETTING
10 PIPETTING | PIPETMAN® CLASSIC
●Each new tip should be pre-rinsed with the liquid
to be pipetted.
●Liquid should never enter the tip holder.
To prevent this:
○Press and release the push button slowly
and smoothly.
○Never turn the pipette upside down.
○Never lay the pipette on its side when
there is liquid in the tip.
●If you use the same tip with a larger volume,
pre-rinse the tip.
●For volatile solvents, saturate the air cushion
in your pipette by aspirating and dispensing
the solvent repeatedly before aspirating the
sample.
●When the temperature of the liquid is
different from the ambient temperature,
pre-rinse the tip several times before use.
●You may remove the tip ejector (refer to
Changing the Tip Ejector on page 15) to
aspirate from very narrow tubes.
●After pipetting acids or other corrosive
liquids that emit vapors, remove the tip
holder; then rinse the piston, O-ring, and seal
with distilled water. For the P1000 model,
use a specific tip holder equipped with a
filter to increase the lifetime of the piston
(refer to ACCESSORIES on page 11).
●Do not pipette liquids with temperatures
above 70°C or below 4°C. The pipette
can be used between4°C and 40°C, but
the specifications may vary according to
the temperature (refer to the ISO 8655-2
standard for conditions of use).

ACCESSORIES
11
PIPETMAN® CLASSIC |USER’S GUIDEPIPETTING | PIPETMAN® CLASSIC
Chapter 4
ACCESSORIES
To make pipetting more comfortable and secure,
Gilson has developed several accessories.
Pipette stands allow users to store pipettes
vertically to avoid the possibility of liquid running
back into the pipette.
DESCRIPTION PART NUMBER
CARROUSEL™ Pipette Stand (7 pipettes) F161401
TRIO™ Stand (3 pipettes) F161405
SINGLE™ Pipette Holder F161406
COLORIS™ Identification Clips identify or personalize
your pipette. Write your name or application to avoid
mix-ups and then snap into place.
DESCRIPTION PART NUMBER
COLORIS clips (mixed colors set of 10) F161301
COLORIS clips (red, set of 10) F161302
COLORIS clips (yellow, set of 10) F161303
COLORIS clips (green, set of 10) F161304
COLORIS clips (blue, set of 10) F161305
COLORIS clips (white, set of 10) F161306
With The JIMMY™, hands-free microtube opener, you
can open both snap-cap and screw-cap microtubes
to increase pipetting efficiency and reduce the
fatigue associated with manual tube opening.
DESCRIPTION PART NUMBER
THE JIMMY (set of 3) F144983
To protect the piston when pipetting corrosive
liquids, you can use a specific tip holder and filter
for the model P1000.
DESCRIPTION PART NUMBER
Corrosion Protection Kit
(tip holder + a bag of 10 filters) F144570
DESCRIPTION PART NUMBER
Plastic ejector P2/P10 with adapter F107027
Plastic ejector P20 F107028
Plastic ejector P100 F107029
Plastic ejector P200 F107030
Plastic ejector P1000 F107031

TROUBLESHOOTING
12 TROUBLESHOOTING | PIPETMAN® CLASSIC
Chapter 5
TROUBLESHOOTING
A quick inspection of the pipette may help you to
detect a problem.
NOTE
You may download the Two Minute
Inspection Poster from the Gilson
website (www.gilson.com), which
shows how to perform a quick
diagnosis of your pipette.
WARNING
Before returning any pipette to
your local Gilson Service Center,
ensure that it is completely free of
chemical, biological, or radioactive
contamination (refer to Cleaning
and Decontamination on page 18).
Please use the included safety bag
to return the pipette to your local
Gilson Service Center.
Troubleshooting Table
The following table may help you to identify and
correct issues you might encounter.
SYMPTOM POSSIBLE CAUSE ACTION
Pipette is
leaking sample
Damaged tip holder Replace the tip
holder
Worn O-ring or seal Replace both parts
Pipette won’t
aspirate
Worn O-ring or seal Replace both parts
Damaged tip holder Replace the tip
holder
Connecting nut is
loose
Tighten connecting
nut
Damaged or corroded
piston
Return pipette to
supplier
Improper repair or
assembly Refer to page 15
Pipette is
inaccurate
Improper repair or
assembly Refer to page 15
Unscrew tip holder Tighten connecting
nut
Connecting nut is
loose
Tighten connecting
nut

TROUBLESHOOTING
13
PIPETMAN® CLASSIC |USER’S GUIDETROUBLESHOOTING | PIPETMAN® CLASSIC
SYMPTOM POSSIBLE CAUSE ACTION
Pipette is not
precise
Tip holder is loose Tighten connecting
nut
Connecting nut is
loose
Tighten connecting
nut
Incorrect operator
technique Operator training
Damaged or corroded
piston
Return pipette to
supplier
Damaged tip holder Replace the tip
holder
Worn O-ring or seal Replace both parts
Tips fall off
or do not fit
correctly
Low quality tips Use PIPETMAN
DIAMOND Tips
Damaged tip holder Replace the tip
holder
Damaged tip ejector Replace tip ejector
Ejector spacer is
missing
Mount the spacer on
the tip ejector
The ejector spacer is
damaged
Replace the ejector
spacer
The tip ejector is loose Assemble the tip
ejector properly
The ejector lock is
misaligned
Align the ejector
lock
If you are not able to resolve the issue, contact
your Gilson representative.

TROUBLESHOOTING
14 TROUBLESHOOTING | PIPETMAN® CLASSIC
Leak Test
This test may be performed at any time to check
that the pipette does not leak, especially after
performing a maintenance or decontamination
procedure. If a pipette fails this test, replace
the O-ring and seal. After making sure that the
pipette is correctly reassembled, repeat this test.
P2 to P200 Models
1. Fit a PIPETMAN® DIAMOND Tip.
2. Set the pipette to the maximum volume,
given in the specifications and pre-rinse.
3. Aspirate the set volume from a beaker of
distilled water.
4. Maintain the pipette in the vertical position
and wait for 20 seconds.
5. If a water droplet appears at the end of the
tip, there is a leak.
6. If you do not see a droplet, re-immerse the
tip below the surface of water.
7. The water level inside the tip should remain
constant. If the level goes down, there is a
leak.
P1000 to P10mL Models
1. Fit a PIPETMAN DIAMOND Tip.
2. Set the pipette to the maximum volume
given in the specifications.
3. Aspirate the set volume from a beaker of
distilled water.
4. Maintain the pipette in the vertical position
and wait for 20 seconds.
5. If a water droplet appears at the end of the
tip, there is a leak.

MAINTENANCE
15
PIPETMAN® CLASSIC |USER’S GUIDETROUBLESHOOTING | PIPETMAN® CLASSIC
Chapter 6
MAINTENANCE
Routine maintenance will help keep your pipette
in good condition, ensuring a continued high
level of performance. Maintenance is limited to
cleaning or autoclaving the parts as specified
under Cleaning and Decontamination on
page 18 or to replacing the push button,
connecting nut, tip ejector, tip holder, seal, and
O-ring.
NOTICE
PIPETMAN P2 and P10 should
not be disassembled. You may
only replace the push button,
tip ejector, and its dual-position
adapter. With these pipettes, if
the tip holder is damaged, the
piston may also be damaged.
After replacing any parts you
should verify the performance
of your pipette following
the verification procedure
available on the Gilson website
(www.gilson.com). If the pipette
needs to be readjusted, please
contact your authorized Gilson
Service Center.
Changing the Tip Ejector
To remove:
Push the ejection
button.
Laterally push the tip
ejector.
Slide and remove the
tip ejector.
To refit:
Push the ejection
button.
Slide the tip ejector along the tip holder.
Clip the tip ejector on the body of the pipette.
1
2
3
1
2
3
1
2
3

MAINTENANCE
16 MAINTENANCE | PIPETMAN® CLASSIC
Color-coded
push button
Connecting
nut
Seal
O-ring
Tip
holder
Tip
ejector
Piston
assembly
Figure 7
Piston assembly (disassembled)

MAINTENANCE
17
PIPETMAN® CLASSIC |USER’S GUIDEMAINTENANCE | PIPETMAN® CLASSIC
Changing the Tip Holder – No
Tools Required
1. Remove the tip ejector (refer to
Changing the Tip Ejector on page 15).
2. Unscrew the connecting nut by turning it
counter-clockwise.
3. Carefully separate the lower and upper parts.
4. Remove the piston assembly, O-ring, and
seal.
5. Clean, autoclave, or replace the tip holder.
6. Reassemble the pipette (refer to
Piston Assembly (Disassembled) on
page 16).
7. Tighten the connecting nut (turn clockwise).
8. Refit the tip ejector (refer to
Changing the Tip Ejector on page 15).
Servicing the Piston Assembly
You may remove the piston assembly for cleaning
purposes only. If the piston assembly is changed,
the pipette must be adjusted and calibrated in a
Gilson authorized Service Center.
NOTICE
The piston assembly must not be
autoclaved.
1. Remove the tip ejector (refer to
Changing the Tip Ejector on page 15).
2. Unscrew the connecting nut by turning it
counterclockwise.
3. Carefully separate the lower and upper parts.
4. Remove the piston assembly, O-ring, and
seal.
5. Clean and decontaminate the piston
assembly.
6. Reassemble the pipette (refer to Figure 7 on
page 16).
7. Tighten the connecting nut (turn clockwise).
8. Refit the tip ejector (refer to
Changing the Tip Ejector on page 15).

MAINTENANCE
18 MAINTENANCE | PIPETMAN® CLASSIC
Changing the O-Ring
The O-ring and seal on the piston must not be
autoclaved. If worn or damaged in any way
(chemical or mechanical), they must be replaced.
The dimensions of the O-ring vary depending on
the model of pipette.
1. Remove the tip ejector (refer to
Changing the Tip Ejector on page 15).
2. Unscrew the connecting nut by turning it
counterclockwise.
3. Carefully separate the lower and upper parts.
4. Remove the piston assembly, O-ring, and
seal.
5. Clean or replace the seal followed by the O-ring.
6. Reassemble the pipette (refer to Figure 7 on
page 16).
7. Tighten the connecting nut (turn clockwise).
8. Refit the tip ejector (refer to
Changing the Tip Ejector on page 15).
Cleaning and Decontamination
PIPETMAN Classic is designed so that the parts
normally in contact with liquid contaminants
can easily be cleaned and decontaminated.
However, because the models P2 and P10 contain
miniaturized parts, it is best not to disassemble
these pipettes yourself. Please contact your
authorized Gilson Service Center.
NOTICE
You can refer to the
decontamination procedure
available on the Gilson website
(www.gilson.com). Liquid must
never enter the upper part
(handle) of any pipette.

MAINTENANCE
19
PIPETMAN® CLASSIC |USER’S GUIDEMAINTENANCE | PIPETMAN® CLASSIC
Cleaning
The pipette must be cleaned, as described below,
before it is decontaminated. Soap solution is
recommended for cleaning PIPETMAN Classic.
EXTERNAL
1. Remove the tip ejector.
2. Wipe the tip ejector with a soft cloth or
lint-free tissue soaked with soap solution.
3. Wipe the entire pipette with a soft cloth or
lint-free tissue soaked with soap solution to
remove all dirty marks. If the pipette is very
dirty, a brush with soft plastic bristles may
be used.
4. Wipe the entire pipette and the tip ejector
with a soft cloth or lint-free tissue soaked
with distilled water.
5. Refit the tip ejector and allow the pipette
to dry.
INTERNAL
Only the following components can be immersed
in a cleaning solution: connecting nut, tip ejector,
tip holder, piston assembly, seal, and O-ring.
1. Disassemble the pipette (refer to Figure 7 on
page 16).
2. Set aside the upper part in a clean, dry
place.
3. Clean the individual components of the
lower part of the pipette using an ultrasonic
bath (20 minutes at 50°C) or with a soft
cloth and brushes. Small round brushes with
soft plastic bristles may be used to clean the
interior of the tip holder.
4. Rinse the individual components with
distilled water.
5. Let the parts dry by evaporation or wipe them
with a clean soft cloth, or lint-free tissue.
6. Reassemble the pipette (refer to Figure 7 on
page 16).

MAINTENANCE
20 MAINTENANCE | PIPETMAN® CLASSIC
Autoclaving
The upper part (body) and the piston assembly
of the pipette are not autoclavable. Only the
following parts may be autoclaved: tip ejector,
tip holder, and connecting nut. The O-ring and
seal are not autoclavable. They may be cleaned
or replaced with the ones found in SPARE PARTS
on page 21.
1. Clean the parts to be autoclaved, especially
the tip holder.
2. Put the parts in an autoclaving sack.
3. Autoclave for 20 minutes at 121°C, 0.1MPa.
4. Check that the parts are dry before
reassembling the pipette.
5. Set the pipette aside equilibrate at room
temperature.
6. Reassemble the pipette (refer to Figure 7 on
page 16).
Chemical Decontamination
You may choose to decontaminate your pipette
chemically, in accordance with your own
procedures. Whatever decontaminant you use,
check with the supplier of the decontaminant
to verify it is compatible with stainless steel
and the plastics used in the construction of the
pipette: PA (Polyamide), PBT (Polybutylene
Terephtalate), PC (Polycarbonate), PC/PBT
(Polycarbonate/ Polybutylene Terephtalate),
POM (Polyoxymethylene), or PVDF
(Polyvinylidene Fluoride).
Upper Part (handle)
1. Wipe the upper part (handle) of the pipette
with a soft cloth or lint-free tissue soaked
with the chosen decontaminant.
2. Wipe the upper part of the pipette with
a soft cloth or lint-free tissue soaked with
distilled water or sterile water.
Lower Part (volumetric module)
Only the following components can be immersed
in a decontaminant solution: connecting nut, tip
ejector, tip holder, piston assembly, seal, and
O-ring.