FBF-C1D1 FLOOD LED LUMINAIRE
NPT ASSEMBLY INSTRUCTIONS
Step 1: Inspect port and ng to ensure that both are free of
contaminants, such as excessive burrs and nicks.
Step 2: Apply a strip of an anaerobic liquid pipe sealant around
the male threads leaving the rst 2 threads uncovered. If no
sealant available use Teon tape (12.7mm x 0.1mm thick).
CAUTION: Teon tape and some pipe sealants are destrucve
to hydraulic components. Always use extreme cauon and
follow manufacturer’s recommendaons for proper applicaon
of any sealant in order to prevent contaminaon.
Operating Instructions
Explosion Proof Luminary
Step 3: Screw into port, nger ght.
Step 4: Wrench ght ng for total thread engagement
(3.5 to 6 turns). Do not back o to achieve alignment, this may
compromise the seal and cause leakage.
CAUTION: Never back o an installed pipe ng to achieve
proper alignment. Loosening installed pipe ngs will corrupt
the seal and contribute to leakage and failure. (*Applicable
standard: ASME B1.20.1-2013)
STEP 1 STEP 3 STEP 4STEP 2
FBF-C1D1 FLOOD LED LUMINAIRE
WIRING INSTRUCTIONS
NOTE: Input Voltage 100-240/277VAC 50/60Hz
or 347/480VAC 50/60Hz
Connect wiring at terminal block in xture as follows:
Black = Line
White = Neutral
Green = Ground
Black (Line)
White (Neutral)
Green (Ground)
( – )
LED DRIVER
( + )
Terminal Block
SERVICING
1. To avoid personal injury, disconnect power to the light and
allow the unit to cool down before performing maintenance.
2. Perform visual, electrical, and mechanical inspecons on
a regular basis. The environment and frequency of use should
determine this. However, it is recommended that checks
should be made at least once a year. Frequency of use and
environment should determine this.
3. The external lens should be cleaned periodically to ensure
connued luminaire performance. Clean the lens with a clean,
damp, non-abrasive, lint-free cloth. If this is not sucient, use
a mild soap or a liquid cleaner. Do not use an abrasive, strong
WALL/CEILING/FLOOR MOUNT
1. The mounng bracket is for the use of wall/ceiling/oor
mounng.
2. Posion the mounng bracket and x it by means of
two (2) M6 and two (2) M8 hex bolts with spring lock washers.
3. Secure the wall/ceiling/oor mounng bracket to the
structure by using screws (not provided).
4. The luminaire can be adjusted up and down by 45° on
wall/ceiling/oor posion only.
5. The luminaire can be adjusted to face down, 90 degrees.
In Ceiling mount applicaons, the lens will be facing down.
PENDANT MOUNT
1. The oodlight is installed with DN20 steel pipe.
2. Fix the luminaire with M5 screws using torque value
of 4 N-m.
Installation and Operation
alkaline or acid cleaner as damage may occur. Organic solvent
is absolutely forbidden to clean the lens.
4. Inspect the cooling ns on the luminaire to ensure that
they are free of any contaminaon (i.e. excessive dust pile-up).
Clean with a non-abrasive cloth if needed.
5. Mechanically check to make sure all parts are properly
assembled.
6. Electrically check to make sure that all connecons are
clean and ght.
Ceiling Mount
Fig. 1
Installation & Operation
Electrical Connection:
1.
2.
3.
4.
Black-wire connects to Line
White-wire connects to Neutral
Green-wire connects to Ground
5.
6.
Wall/Ceiling/Floor Mounting Bracket:
Wall Type:
Ceiling Type: Pendant Type:
Floor Type:
7.
8.
9.
10.
11.
Fig. 3 Fig. 4
Operating Instructions Hazardous Location Series
Fig. 2
200
140
56
R5.5
Angle 0-180°
Adjustable Expansion bolts
(Gasket+Washers included) M10
Expansion bolts
DN20 USER SELF
2ʇ3
M5 cross recess pan head screw
(Gasket+Washers included) M10
Angle 0-180° Adjustable
Expansion bolts
(Gasket+Washers included) M10
The Angle mark
342 271
176
239
45°
Terminal
Block LED Driver
2+'*=/8+9
:52+*25'*
=./:+4+;:8'2
GREEN (GROUND)
(2')12/4+
')/46;:
REV: A 3.0
6GMK
Servicing
t
t
t
t
t
t
Operating Instructions Hazardous Location Series
Housing
t
t
t
t
t
REV: A 3.0
6GMK
HazLoc LED Luminaire
To avoid personal injury, disconnect power to the light and allow the unit to cool down before performing
maintenance.
6KXLUXS\OY[GRKRKIZXOIGRGTJSKINGTOIGROTYVKIZOUTYUTGXKM[RGXHGYOY:NKKT\OXUTSKTZGTJLXKW[KTI_
of use should determine this. However, it is recommended that checks should be made at least once a year.
,XKW[KTI_UL[YKGTJKT\OXUTSKTZYNU[RJJKZKXSOTKZNOY
The external glass should be cleaned periodically to ensure continued luminaire performance. Clean the
MRGYY]OZNGIRKGTJGSVTUTGHXGYO\KROTZLXKKIRUZN/LZNOYOYTUZY[LLOIOKTZ[YKGSORJYUGVUXGROW[OJ
cleaner. Do not use an abrasive, strong alkaline or acid cleaner as damage may occur.
/TYVKIZZNKIUUROTMLOTYUTZNKR[SOTGOXKZUKTY[XKZNGZZNK_GXKLXKKULGT_IUTZGSOTGZOUT
(i.e. excessive dust build-up). Clean with a non-abrasive cloth if needed.
Mechanically check to make sure all parts are properly assembled.
Electrically check to make sure that all connections are clean and tight.
Heavy-duty Anodized Die Casting Aluminum
Shell surface of electrostatic spraying, Long lasting and Durable
Shell protection, Over-voltage and Over-heat protection
+^VUYKJLGYZKTKXY]OZNW[GROZ_YZGOTRKYYYZKKR
Excellent anti-corrosive property
General Wiring Diagram
CAUTION:
HazLoc LED Luminaire
Turn off electrical power at fuse
or circuit breaker box before wiring fixture to
the power supply.
Connecting panels to AC source supply:
All units must be individually connected to
the AC supply.
Black = Line
White = Neutral
Green = Ground
2UUYKTZNKZKT3NK^GMUTHRUZY]OZNYVXOTM]GYNKXYGTJT[ZYUL:GTQ)U\KX]OZNZUXW[K\GR[K4S
:NKZNXKGJULKTZX_NURKUL:GTQOYȕ46:'ZZGINZNK:GTQZUY[OZGHRKIUTJ[OZ
/TYKZZNK]OXKLXUSU[ZYOJKZNXU[MNZNKIUTJ[OZGTJZNKKTZX_NURKUL:GTQGTJZNKTIUTTKIZZU:KXSOTGR(RUIQ
/TZXUJ[IKZNK]OXKYULHXGTINIOXI[OZGYLURRU]OTM
Check the tightness of conduit and Tank Cover.
The mounting bracket is for the use of
wall/ceiling/floor mounting.
The luminaire can be adjusted facing
down 90° from vertical = Lens
horizontal facing down on ceiling
position.(Figure 3)
The luminaire can be adjusted up and
down by 45° on wall/floor position only. (Figure 2)
Secure the wall/ceiling/floor mounting
bracket to the structure by using.
screws (not provided). (Figure 1)
6UYOZOUTZNKSU[TZOTMHXGIQKZGTJLO^OZ
by means of two M6 and two M8
hexagon bolts with spring lock washers.
Re-attach the Tank Cover and tight it by ten M6 hexagon blots with
YVXOTM]GYNKXYGTJT[ZY]OZNZUXW[K\GR[K4S
12.
13.
The luminaire are installed with DN20 steel pipe.
,O^ZNKR[SOTGOXK]OZN3YIXK]Y]OZNZUXW[K
value 4 N-m.(Figure 4)
Pendant Type:
Floor Mount
Fig. 1
Installation & Operation
Electrical Connection:
1.
2.
3.
4.
Black-wire connects to Line
White-wire connects to Neutral
Green-wire connects to Ground
5.
6.
Wall/Ceiling/Floor Mounting Bracket:
Wall Type:
Ceiling Type: Pendant Type:
Floor Type:
7.
8.
9.
10.
11.
Fig. 3 Fig. 4
Operating Instructions Hazardous Location Series
Fig. 2
200
140
56
R5.5
Angle 0-180°
Adjustable Expansion bolts
(Gasket+Washers included) M10
Expansion bolts
DN20 USER SELF
2ʇ3
M5 cross recess pan head screw
(Gasket+Washers included) M10
Angle 0-180° Adjustable
Expansion bolts
(Gasket+Washers included) M10
The Angle mark
342 271
176
239
45°
Terminal
Block LED Driver
2+'*=/8+9
:52+*25'*
=./:+4+;:8'2
GREEN (GROUND)
(2')12/4+
')/46;:
REV: A 3.0
6GMK
Servicing
t
t
t
t
t
t
Operating Instructions Hazardous Location Series
Housing
t
t
t
t
t
REV: A 3.0
6GMK
HazLoc LED Luminaire
To avoid personal injury, disconnect power to the light and allow the unit to cool down before performing
maintenance.
6KXLUXS\OY[GRKRKIZXOIGRGTJSKINGTOIGROTYVKIZOUTYUTGXKM[RGXHGYOY:NKKT\OXUTSKTZGTJLXKW[KTI_
of use should determine this. However, it is recommended that checks should be made at least once a year.
,XKW[KTI_UL[YKGTJKT\OXUTSKTZYNU[RJJKZKXSOTKZNOY
The external glass should be cleaned periodically to ensure continued luminaire performance. Clean the
MRGYY]OZNGIRKGTJGSVTUTGHXGYO\KROTZLXKKIRUZN/LZNOYOYTUZY[LLOIOKTZ[YKGSORJYUGVUXGROW[OJ
cleaner. Do not use an abrasive, strong alkaline or acid cleaner as damage may occur.
/TYVKIZZNKIUUROTMLOTYUTZNKR[SOTGOXKZUKTY[XKZNGZZNK_GXKLXKKULGT_IUTZGSOTGZOUT
(i.e. excessive dust build-up). Clean with a non-abrasive cloth if needed.
Mechanically check to make sure all parts are properly assembled.
Electrically check to make sure that all connections are clean and tight.
Heavy-duty Anodized Die Casting Aluminum
Shell surface of electrostatic spraying, Long lasting and Durable
Shell protection, Over-voltage and Over-heat protection
+^VUYKJLGYZKTKXY]OZNW[GROZ_YZGOTRKYYYZKKR
Excellent anti-corrosive property
General Wiring Diagram
CAUTION:
HazLoc LED Luminaire
Turn off electrical power at fuse
or circuit breaker box before wiring fixture to
the power supply.
Connecting panels to AC source supply:
All units must be individually connected to
the AC supply.
Black = Line
White = Neutral
Green = Ground
2UUYKTZNKZKT3NK^GMUTHRUZY]OZNYVXOTM]GYNKXYGTJT[ZYUL:GTQ)U\KX]OZNZUXW[K\GR[K4S
:NKZNXKGJULKTZX_NURKUL:GTQOYȕ46:'ZZGINZNK:GTQZUY[OZGHRKIUTJ[OZ
/TYKZZNK]OXKLXUSU[ZYOJKZNXU[MNZNKIUTJ[OZGTJZNKKTZX_NURKUL:GTQGTJZNKTIUTTKIZZU:KXSOTGR(RUIQ
/TZXUJ[IKZNK]OXKYULHXGTINIOXI[OZGYLURRU]OTM
Check the tightness of conduit and Tank Cover.
The mounting bracket is for the use of
wall/ceiling/floor mounting.
The luminaire can be adjusted facing
down 90° from vertical = Lens
horizontal facing down on ceiling
position.(Figure 3)
The luminaire can be adjusted up and
down by 45° on wall/floor position only. (Figure 2)
Secure the wall/ceiling/floor mounting
bracket to the structure by using.
screws (not provided). (Figure 1)
6UYOZOUTZNKSU[TZOTMHXGIQKZGTJLO^OZ
by means of two M6 and two M8
hexagon bolts with spring lock washers.
Re-attach the Tank Cover and tight it by ten M6 hexagon blots with
YVXOTM]GYNKXYGTJT[ZY]OZNZUXW[K\GR[K4S
12.
13.
The luminaire are installed with DN20 steel pipe.
,O^ZNKR[SOTGOXK]OZN3YIXK]Y]OZNZUXW[K
value 4 N-m.(Figure 4)
Pendant Type:
Fig. 1
Installation & Operation
Electrical Connection:
1.
2.
3.
4.
Black-wire connects to Line
White-wire connects to Neutral
Green-wire connects to Ground
5.
6.
Wall/Ceiling/Floor Mounting Bracket:
Wall Type:
Ceiling Type: Pendant Type:
Floor Type:
7.
8.
9.
10.
11.
Fig. 3 Fig. 4
Operating Instructions Hazardous Location Series
Fig. 2
200
140
56
R5.5
Angle 0-180°
Adjustable Expansion bolts
(Gasket+Washers included) M10
Expansion bolts
DN20 USER SELF
2ʇ3
M5 cross recess pan head screw
(Gasket+Washers included) M10
Angle 0-180° Adjustable
Expansion bolts
(Gasket+Washers included) M10
The Angle mark
342 271
176
239
45°
Terminal
Block LED Driver
2+'*=/8+9
:52+*25'*
=./:+4+;:8'2
GREEN (GROUND)
(2')12/4+
')/46;:
REV: A 3.0
6GMK
Servicing
t
t
t
t
t
t
Operating Instructions Hazardous Location Series
Housing
t
t
t
t
t
REV: A 3.0
6GMK
HazLoc LED Luminaire
To avoid personal injury, disconnect power to the light and allow the unit to cool down before performing
maintenance.
6KXLUXS\OY[GRKRKIZXOIGRGTJSKINGTOIGROTYVKIZOUTYUTGXKM[RGXHGYOY:NKKT\OXUTSKTZGTJLXKW[KTI_
of use should determine this. However, it is recommended that checks should be made at least once a year.
,XKW[KTI_UL[YKGTJKT\OXUTSKTZYNU[RJJKZKXSOTKZNOY
The external glass should be cleaned periodically to ensure continued luminaire performance. Clean the
MRGYY]OZNGIRKGTJGSVTUTGHXGYO\KROTZLXKKIRUZN/LZNOYOYTUZY[LLOIOKTZ[YKGSORJYUGVUXGROW[OJ
cleaner. Do not use an abrasive, strong alkaline or acid cleaner as damage may occur.
/TYVKIZZNKIUUROTMLOTYUTZNKR[SOTGOXKZUKTY[XKZNGZZNK_GXKLXKKULGT_IUTZGSOTGZOUT
(i.e. excessive dust build-up). Clean with a non-abrasive cloth if needed.
Mechanically check to make sure all parts are properly assembled.
Electrically check to make sure that all connections are clean and tight.
Heavy-duty Anodized Die Casting Aluminum
Shell surface of electrostatic spraying, Long lasting and Durable
Shell protection, Over-voltage and Over-heat protection
+^VUYKJLGYZKTKXY]OZNW[GROZ_YZGOTRKYYYZKKR
Excellent anti-corrosive property
General Wiring Diagram
CAUTION:
HazLoc LED Luminaire
Turn off electrical power at fuse
or circuit breaker box before wiring fixture to
the power supply.
Connecting panels to AC source supply:
All units must be individually connected to
the AC supply.
Black = Line
White = Neutral
Green = Ground
2UUYKTZNKZKT3NK^GMUTHRUZY]OZNYVXOTM]GYNKXYGTJT[ZYUL:GTQ)U\KX]OZNZUXW[K\GR[K4S
:NKZNXKGJULKTZX_NURKUL:GTQOYȕ46:'ZZGINZNK:GTQZUY[OZGHRKIUTJ[OZ
/TYKZZNK]OXKLXUSU[ZYOJKZNXU[MNZNKIUTJ[OZGTJZNKKTZX_NURKUL:GTQGTJZNKTIUTTKIZZU:KXSOTGR(RUIQ
/TZXUJ[IKZNK]OXKYULHXGTINIOXI[OZGYLURRU]OTM
Check the tightness of conduit and Tank Cover.
The mounting bracket is for the use of
wall/ceiling/floor mounting.
The luminaire can be adjusted facing
down 90° from vertical = Lens
horizontal facing down on ceiling
position.(Figure 3)
The luminaire can be adjusted up and
down by 45° on wall/floor position only. (Figure 2)
Secure the wall/ceiling/floor mounting
bracket to the structure by using.
screws (not provided). (Figure 1)
6UYOZOUTZNKSU[TZOTMHXGIQKZGTJLO^OZ
by means of two M6 and two M8
hexagon bolts with spring lock washers.
Re-attach the Tank Cover and tight it by ten M6 hexagon blots with
YVXOTM]GYNKXYGTJT[ZY]OZNZUXW[K\GR[K4S
12.
13.
The luminaire are installed with DN20 steel pipe.
,O^ZNKR[SOTGOXK]OZN3YIXK]Y]OZNZUXW[K
value 4 N-m.(Figure 4)
Pendant Type:
Bracket Hole Pattern
Wall Mount
Fig. 1
Installation & Operation
Electrical Connection:
1.
2.
3.
4.
Black-wire connects to Line
White-wire connects to Neutral
Green-wire connects to Ground
5.
6.
Wall/Ceiling/Floor Mounting Bracket:
Wall Type:
Ceiling Type: Pendant Type:
Floor Type:
7.
8.
9.
10.
11.
Fig. 3 Fig. 4
Operating Instructions Hazardous Location Series
Fig. 2
200
140
56
R5.5
Angle 0-180°
Adjustable Expansion bolts
(Gasket+Washers included) M10
Expansion bolts
DN20 USER SELF
2ʇ3
M5 cross recess pan head screw
(Gasket+Washers included) M10
Angle 0-180° Adjustable
Expansion bolts
(Gasket+Washers included) M10
The Angle mark
45°
Terminal
Block LED Driver
2+'*=/8+9
:52+*25'*
=./:+4+;:8'2
GREEN (GROUND)
(2')12/4+
')/46;:
REV: A 3.0
6GMK
Servicing
t
t
t
t
t
t
Operating Instructions Hazardous Location Series
Housing
t
t
t
t
t
REV: A 3.0
6GMK
HazLoc LED Luminaire
To avoid personal injury, disconnect power to the light and allow the unit to cool down before performing
maintenance.
6KXLUXS\OY[GRKRKIZXOIGRGTJSKINGTOIGROTYVKIZOUTYUTGXKM[RGXHGYOY:NKKT\OXUTSKTZGTJLXKW[KTI_
of use should determine this. However, it is recommended that checks should be made at least once a year.
,XKW[KTI_UL[YKGTJKT\OXUTSKTZYNU[RJJKZKXSOTKZNOY
The external glass should be cleaned periodically to ensure continued luminaire performance. Clean the
MRGYY]OZNGIRKGTJGSVTUTGHXGYO\KROTZLXKKIRUZN/LZNOYOYTUZY[LLOIOKTZ[YKGSORJYUGVUXGROW[OJ
cleaner. Do not use an abrasive, strong alkaline or acid cleaner as damage may occur.
/TYVKIZZNKIUUROTMLOTYUTZNKR[SOTGOXKZUKTY[XKZNGZZNK_GXKLXKKULGT_IUTZGSOTGZOUT
(i.e. excessive dust build-up). Clean with a non-abrasive cloth if needed.
Mechanically check to make sure all parts are properly assembled.
Electrically check to make sure that all connections are clean and tight.
Heavy-duty Anodized Die Casting Aluminum
Shell surface of electrostatic spraying, Long lasting and Durable
Shell protection, Over-voltage and Over-heat protection
+^VUYKJLGYZKTKXY]OZNW[GROZ_YZGOTRKYYYZKKR
Excellent anti-corrosive property
General Wiring Diagram
CAUTION:
HazLoc LED Luminaire
Turn off electrical power at fuse
or circuit breaker box before wiring fixture to
the power supply.
Connecting panels to AC source supply:
All units must be individually connected to
the AC supply.
Black = Line
White = Neutral
Green = Ground
2UUYKTZNKZKT3NK^GMUTHRUZY]OZNYVXOTM]GYNKXYGTJT[ZYUL:GTQ)U\KX]OZNZUXW[K\GR[K4S
:NKZNXKGJULKTZX_NURKUL:GTQOYȕ46:'ZZGINZNK:GTQZUY[OZGHRKIUTJ[OZ
/TYKZZNK]OXKLXUSU[ZYOJKZNXU[MNZNKIUTJ[OZGTJZNKKTZX_NURKUL:GTQGTJZNKTIUTTKIZZU:KXSOTGR(RUIQ
/TZXUJ[IKZNK]OXKYULHXGTINIOXI[OZGYLURRU]OTM
Check the tightness of conduit and Tank Cover.
The mounting bracket is for the use of
wall/ceiling/floor mounting.
The luminaire can be adjusted facing
down 90° from vertical = Lens
horizontal facing down on ceiling
position.(Figure 3)
The luminaire can be adjusted up and
down by 45° on wall/floor position only. (Figure 2)
Secure the wall/ceiling/floor mounting
bracket to the structure by using.
screws (not provided). (Figure 1)
6UYOZOUTZNKSU[TZOTMHXGIQKZGTJLO^OZ
by means of two M6 and two M8
hexagon bolts with spring lock washers.
Re-attach the Tank Cover and tight it by ten M6 hexagon blots with
YVXOTM]GYNKXYGTJT[ZY]OZNZUXW[K\GR[K4S
12.
13.
The luminaire are installed with DN20 steel pipe.
,O^ZNKR[SOTGOXK]OZN3YIXK]Y]OZNZUXW[K
value 4 N-m.(Figure 4)
Pendant Type:
Pendant Mount
Fig. 1
Installation & Operation
Electrical Connection:
1.
2.
3.
4.
Black-wire connects to Line
White-wire connects to Neutral
Green-wire connects to Ground
5.
6.
Wall/Ceiling/Floor Mounting Bracket:
Wall Type:
Ceiling Type: Pendant Type:
Floor Type:
7.
8.
9.
10.
11.
Fig. 3 Fig. 4
Operating Instructions Hazardous Location Series
Fig. 2
200
140
56
R5.5
Angle 0-180°
Adjustable Expansion bolts
(Gasket+Washers included) M10
Expansion bolts
DN20 USER SELF
2ʇ3
M5 cross recess pan head screw
(Gasket+Washers included) M10
Angle 0-180° Adjustable
Expansion bolts
(Gasket+Washers included) M10
The Angle mark
342 271
176
239
45°
Terminal
Block LED Driver
2+'*=/8+9
:52+*25'*
=./:+4+;:8'2
GREEN (GROUND)
(2')12/4+
')/46;:
REV: A 3.0
6GMK
Servicing
t
t
t
t
t
t
Operating Instructions Hazardous Location Series
Housing
t
t
t
t
t
REV: A 3.0
6GMK
HazLoc LED Luminaire
To avoid personal injury, disconnect power to the light and allow the unit to cool down before performing
maintenance.
6KXLUXS\OY[GRKRKIZXOIGRGTJSKINGTOIGROTYVKIZOUTYUTGXKM[RGXHGYOY:NKKT\OXUTSKTZGTJLXKW[KTI_
of use should determine this. However, it is recommended that checks should be made at least once a year.
,XKW[KTI_UL[YKGTJKT\OXUTSKTZYNU[RJJKZKXSOTKZNOY
The external glass should be cleaned periodically to ensure continued luminaire performance. Clean the
MRGYY]OZNGIRKGTJGSVTUTGHXGYO\KROTZLXKKIRUZN/LZNOYOYTUZY[LLOIOKTZ[YKGSORJYUGVUXGROW[OJ
cleaner. Do not use an abrasive, strong alkaline or acid cleaner as damage may occur.
/TYVKIZZNKIUUROTMLOTYUTZNKR[SOTGOXKZUKTY[XKZNGZZNK_GXKLXKKULGT_IUTZGSOTGZOUT
(i.e. excessive dust build-up). Clean with a non-abrasive cloth if needed.
Mechanically check to make sure all parts are properly assembled.
Electrically check to make sure that all connections are clean and tight.
Heavy-duty Anodized Die Casting Aluminum
Shell surface of electrostatic spraying, Long lasting and Durable
Shell protection, Over-voltage and Over-heat protection
+^VUYKJLGYZKTKXY]OZNW[GROZ_YZGOTRKYYYZKKR
Excellent anti-corrosive property
General Wiring Diagram
CAUTION:
HazLoc LED Luminaire
Turn off electrical power at fuse
or circuit breaker box before wiring fixture to
the power supply.
Connecting panels to AC source supply:
All units must be individually connected to
the AC supply.
Black = Line
White = Neutral
Green = Ground
2UUYKTZNKZKT3NK^GMUTHRUZY]OZNYVXOTM]GYNKXYGTJT[ZYUL:GTQ)U\KX]OZNZUXW[K\GR[K4S
:NKZNXKGJULKTZX_NURKUL:GTQOYȕ46:'ZZGINZNK:GTQZUY[OZGHRKIUTJ[OZ
/TYKZZNK]OXKLXUSU[ZYOJKZNXU[MNZNKIUTJ[OZGTJZNKKTZX_NURKUL:GTQGTJZNKTIUTTKIZZU:KXSOTGR(RUIQ
/TZXUJ[IKZNK]OXKYULHXGTINIOXI[OZGYLURRU]OTM
Check the tightness of conduit and Tank Cover.
The mounting bracket is for the use of
wall/ceiling/floor mounting.
The luminaire can be adjusted facing
down 90° from vertical = Lens
horizontal facing down on ceiling
position.(Figure 3)
The luminaire can be adjusted up and
down by 45° on wall/floor position only. (Figure 2)
Secure the wall/ceiling/floor mounting
bracket to the structure by using.
screws (not provided). (Figure 1)
6UYOZOUTZNKSU[TZOTMHXGIQKZGTJLO^OZ
by means of two M6 and two M8
hexagon bolts with spring lock washers.
Re-attach the Tank Cover and tight it by ten M6 hexagon blots with
YVXOTM]GYNKXYGTJT[ZY]OZNZUXW[K\GR[K4S
12.
13.
The luminaire are installed with DN20 steel pipe.
,O^ZNKR[SOTGOXK]OZN3YIXK]Y]OZNZUXW[K
value 4 N-m.(Figure 4)
Pendant Type:
4 5
