GoldenDesigns GDI6106 User manual

GDI6106 / DYN9101
1 –2 Person Sauna
OWNER’S MANUAL
FOR CERAMIC AND CARBON MODEL
SAUNAS FOR INDOOR USE ONLY
120VAC 15 AMP DEDICATED CIRCUIT
Sauna: Now you can enjoy the European secret for youthful vitality.
Carefully and thoroughly read this manual before using the sauna. We
recommend keeping this manual for regular review and future
reference.

*PLEASE READ INSTRUCTIONS BEFORE ASSEMBLY*
GDI-6106
*The above assembly diagrams are for quick reference visual guides only. All
sauna models are not shown. Parts and accessories may vary.

1
WHAT ARE INFRARED RAYS?
Infrared is the band of light we perceive as heat. We cannot see this band of light with the naked eye, but we
can feel this type of light in the form of heat. Our sun produces most of its energy output in the infrared
segment of the spectrum. Infrared rays heat your body without having to heat the air in-between. This process
is called conversion.
The infrared is divided into 3 segments by wavelengths measured in microns: near infrared: 0.76-1.5
microns; middle infrared: 1.5-5.6 microns; and far infrared: 5.6-1000 microns. Among these segments, only
far infrared penetrates organic substances such as the human body two to three inches so that the
warming effect is very uniform.
X R a y s
Cosmic R a y s
Infrared R a y s
Gamma R a y s
UV R a y s
Wavelength (in microns )
0.76 1.5 5.6 1000
Near
Ir
M iddle
Ir
FarInfrared R a y s
ARE INFRARED RAYS SAFE?
Because infrared rays are part of sunlight, they are not only safe but also highly beneficial to our bodies on a
cellular level. Health professionals have used infrared heat lamps for decades to treat muscle and joint
problems. In hospital baby care units, incubators are often equipped with infrared heating systems to keep
newborn babies warm.

2
HOW IT WORKS
Infrared Saunas differ from traditional saunas in that they use infrared radiant energy to directly penetrate into
the body's tissue to produce perspiration.
Traditional saunas use steam to heat the air inside the sauna, which then heats your body until you begin to
perspire. In order for this to be effective, temperatures would need to reach in the upwards of 190 degrees
Fahrenheit. Infrared saunas only need a temperature of up to 120 degrees Fahrenheit to obtain the same
effect. This lower temperature makes the environment more tolerable and allows you to breathe easier.
Traditional Infrared
BENEFITS
Because infrared rays penetrate the body through conversion, there is a deep heating effect in both the muscle
tissues and internal organs without putting too much burden on the heart.
Our body reacts to the increased heating through the natural cooling process of perspiring. Through the
perspiration process, acid and waste residue like toxins, sodium, alcohol, nicotine, cholesterol and the
potentially carcinogenic heavy metals are removed from the cells (especially zinc, lead, nickel, cadmium,
etc). The pores of our skin open and discharge waste products shedding any old skin cells leaving the skin
glowing and clean, with improved tone, elasticity, texture, and color.
Over the last 25 years, Japanese and Chinese researchers and clinicians have completed extensive research
on infrared treatments and have reported many provocative findings. In Japan, there is an "infrared society"
composed of medical doctors and physical therapists dedicated to furthering infrared research. Their findings
support the health benefits of infrared therapy as a method of healing.

3
Benefits include, but are not limited to:
- Pain relief from Rheumatoid Arthritis
- Relaxing muscle spasms
- Increasing blood circulation
- Cardiovascular conditioning
- Clears rashes, acne
- Reduces cellulite
- Removes toxins and mineral waste
- Reduces stress and fatigue
- Enhances skin tone
SAUNA MAINTENANCE
Since infrared saunas do not require hot rocks, water, or steam to operate, they require very little
maintenance. You can simply wipe it down with water and a soft clean cloth. Do not use any cleaning
chemicals as they can be absorbed into the wood and be released into your sauna during use.
DISCLAIMER
The infrared rays emitted by your sauna are reported to offer a wide range of possible therapeutic benefits
based on research completed over the last 25 years from all around the world. These benefits are presented
for reference purposes only and no implication of infrared saunas creating a cure for or treating any disease is
implied nor should it be inferred. If you have a health condition, are taking prescription drugs, or have acute
joint injuries, please consult your physician before starting infrared therapy. Persons with surgical implants
(metal pins and rods, artificial joints, silicone, or other types of surgical implants) typically do not experience
any adverse effects, but should also consult their physician or surgeon before starting infrared therapy.
CAUTION: Exit sauna immediately if you feel dizzy,
sleepy, or any discomfort.

4
TABLE OF CONTENTS
Product Introduction 4
Parts Description 5
Assembly Instructions 9
Operating the Sauna 15
Tips for Using Your Sauna 19
Safety Instructions 20
Safeguards for Your Sauna 21
Troubleshooting Guide 21
Warranty 23
Warranty Card 25
WARNING: Visually inspect all heaters before assembly to make sure they are not damaged. Any
excessive vibrations during transport could cause damage to the heating elements. DO NOT START
the sauna if damage is detected! Contact your dealer or manufacturer for troubleshooting and
replacement parts.
1. Product Introduction
The infrared sauna room is composed of a wood cabin, infrared heat emitters, and a control system. The
wood cabin includes a FRONT PANEL, REAR PANEL, LEFT SIDE PANEL, RIGHT SIDE PANEL, BENCH,
BENCH EMITTER PANEL, FLOOR PANEL, ROOF PANEL, and ROOF COVER. The infrared sauna
comes with control panels, a back protection grid (optional), a drink shelf, a reading lamp, and infrared heat
emitters.
NOTE: The pictures and diagrams shown within this owner’s manual are representations of this model.
Actual model may vary.

5
PARTS DESCRIPTION
A. FRONT OF SAUNA (see figure 1)
B. INSIDE OF SAUNA (see figure 2)
Figure 1 Figure 2
1) Door Handle
2) Tempered Glass Door
3) Ventilation Grid
4) Speaker
5) Reading Lamp
6) Control Panel
7) Temperature Sensor
8) Heat Emitter
9) Bench Panel
10) Back Protection Grid (Ceramic Model Saunas Only)
11) Glass Window Panel
12) MP3 Auxiliary Socket

6
I. Power Supply (Control Box)
The POWER SUPPLY BOX is the control center of the sauna room. It is installed on the
ROOF PANEL and has input/outputs connected to it as seen below. (see Figure 1)
Power Supply 1 Power Supply 2
Figure 1 Figure 1A
MAIN POWER - main power of the sauna room POWER IN - main power of the sauna room
HT1, HT2, HT3, HT4 –heater cords HT1, HT2, HT3, HT4, HT5, HT6 –heater
cords
LIGHT –chromotherapy lights LAMPROOF –roof lamp power (optional)
ROOF LAMP - roof lamp (optional) LIGHTING –chromotherapy lights
CTRL - control panel connection PANEL CONTROL –control panel
connection
CD/SIG - signal cable group FUSE RESET –protects against power
surges
FUSE RESET –protects against power surges
II. Component Labeling
POWER Power Cord
HT1, HT2, HT3, HT4, HT5, HT6 Emitter (heater) power cords
LIGHT Reading lamp connector
ROOF LAMP Roof lamp connector (not available on all
models)
CTRL Control panel connector
CD/SIG For speakers/temperature sensor/buzzer/etc.
connectors
CD-POWER CD/radio power connector (not available on all
models)
FAN-POWER CD/radio fan power connector (not available on
all
models)
L/SPEAKER Left speaker connector
R/SPEAKER Right speaker connector
TEMP SENSOR Temperature sensor

7
III. MP3 Auxiliary Socket (Optional)
The MP3 Auxiliary Socket allows you to connect a MP3 player or radio (with auxiliary out function) to
the speakers for your listening pleasure. (see figure 4)
Figure 4
IV. Buckles
A. External Buckles
The external buckles are used to connect the LEFT and RIGHT SIDE PANELS to the
REAR PANEL. (see figure 5)
Figure 5
B. Guide and Guide Inserts
The guide and guide inserts are used to connect the FRONT PANEL to the RIGHT SIDE
PANEL and the LEFT SIDE PANEL. (see figure 6)

8
Figure 6
V. Panel Descriptions
For easier installation, please understand and distinguish the differences between each panel.
A. Floor Panel
When the floor panel faces upward, you will find (2) raised moldings, one along what will be the
front and one along what will be the rear of the sauna room. (see figure 7)
Figure 7
B. Understanding The Difference Between The Top And Bottom Of The Wall Panels
The (4) panels are in the upright position when the moldings are at the top. The moldings will face
inward. (see figure 8)

9
Figure
8
C. Rear Panel
The rear panel is the panel with the buckles. The buckles are mounted on the outside of the
rear panel. (see figure 9)
Figure
9
D. Understanding The Difference Between The Inside And Outside Of The Rear Panel
You will find the heat emitters on the inside of the rear panel.
Assembly Instructions
A. Choose a good location to install the sauna
1. The location must be dry, leveled, and away from any source of water
2. MAIN POWER cord must be easily accessible
3. Two adults are required for installation
4. Wood cabin installation order: Floor Panel Front Panel Right Side Panel Left Side
Panel Rear Panel Bench Emitter Panel Bench Roof Panel Roof Cover
5. Tools Required: Philips Screwdriver and Ladder

10
B. Installing the FLOOR PANEL
1. Place the FLOOR PANEL on the floor. Some models have wood braces that must be
installed on the underside of the FLOOR PANEL. Please check to see if such wood braces
were packed in the box containing the FLOOR PANEL. If so, mount according to the
designated labels located on the underside of the FLOOR PANEL. Once installed, turn the
FLOOR PANEL right side up. Make sure the front side of the FLOOR PANEL is facing the
correct direction. The notches on the floor will be closer to the rear of the sauna than the front
of the sauna. (see Panel Descriptions)
C. Installing the FRONT PANEL and SIDE PANELS
1. Place the FRONT PANEL onto the recessed area on the FLOOR PANEL. Align guides on the
RIGHT SIDE PANEL with the guide inserts on the FRONT PANEL. The RIGHT SIDE PANEL
will need to be lifted in order to lock the guide inserts on the FRONT PANEL into the guides on
the RIGHT SIDE PANEL. Secure in place by pulling down on the RIGHT SIDE PANEL. Make
sure all the guides are locked in place and the top of the LEFT SIDE PANEL is even with the
FRONT PANEL. Do the same with the LEFT SIDE PANEL. (see figure 10)
Figure 10
D. Installing the REAR PANEL
1. Remove the protection paper from the buckles. Place the REAR PANEL onto the recessed
area on the FLOOR PANEL. Attach the REAR PANEL to the SIDE PANELS and buckle
together. (see figure 11)

11
Figure 11
E. Installing the FLOOR EMITTER PANEL (Carbon Models Only), BENCH EMITTER PANEL,
BENCH, and REAR PANEL GRID (Ceramic Models Only)
1. If your model is not equipped with the FLOOR EMITTER PANEL, then skip to 2. If your model
is equipped with the FLOOR EMITTER PANEL, then place it on the floor towards the front of
the sauna. (see figure 12 - 13)
Figure 12 Figure 13
2. Slide down the BENCH EMITTER PANEL by lining up its sides with the vertical guides on
each side panel. The emitter grid will face outward (toward the front of the sauna). Push the
BENCH EMITTER PANEL all the way down until it is touching the FLOOR PANEL and is
secured in place.
3. Plug in the BENCH EMITTER connector to the inlet located on the REAR PANEL.
4. Install the BENCH by sliding it over the horizontal bench guides on the side panels. Push the
BENCH all the way in until it touches the REAR PANEL and is secured in place. Make sure to
install the BENCH with the smooth and finished side facing up.
5. On selected ceramic heater models, you must install the REAR PANEL GRID. (see figure 14)

12
Figure 14
F. Installing the ROOF PANEL
1. The side with the power supply box faces upward.
2. The edge nearest the power supply is the front of the ROOF PANEL. Be careful of the wires
coming from the REAR PANEL when you set the ROOF PANEL down onto the panels. Feed
the wires through the holes in the ROOF PANEL. Do the same for any wiring harnesses
coming from the SIDE or FRONT PANELS.
3. Be careful not to force the ROOF PANEL into place. Make sure that the wires are properly fed
through the holes. (see figure 15)
4. When all the wires are fed through their appropriate holes, lower the ROOF PANEL into place.
5. The four screws taped to the four sides of the ROOF PANEL are used to mount the ROOF
PANEL to each of the wall panels. Use the pre-drilled holes on the four sides of the ROOF
PANEL.
Figure 15
G. Connecting the plugs on the ROOF PANEL
(POWER SUPPLY 1)
1. Connect the plugs according to the respective labels. (see figure 16 –18)

13
2. Connect the CTRL plug from the power supply to the CTRL plug from the control panel.
Then screw together.
3. Connect the buzzer connection. (see figure 19)(not available on models with Bluetooth)
Figure 16 Figure 16a
Figure 17 Figure 18

14
(POWER SUPPLY 2)
1. Connect the plugs according to their respective labels. (see Figure 18)
2. You will need to connect the right and left speaker connectors, the MP3 connector, and the
CTRL harness wire connector.
Before Connecting After Connecting
Figure 18
H. Installing the TEMPERATURE SENSOR
1. Enter the sauna and remove the protective covering from the TEMPERATURE SENSOR.
Situate the TEMPERATURE SENSOR so that it is vertical, pointing downward. (see figure 20)
Figure 20
Note: Some sauna models are shipped with a spare TEMPERATURE SENSOR in case the
TEMPERATURE SENSOR is damaged in transit. The manufacturer decides this according to
sauna models and packaging.

15
I. Putting on the ROOF COVER
1. Place the ROOF COVER over the top of the sauna. Be cautious when pulling the power
cord through the hole in the roof cover. Gently place the ROOF COVER onto the ROOF
PANEL. When the edges are aligned, screw the ROOF COVER to the roof panel. (see figure
21)
Figure 21
J. Optional MP3 Shelf
1. If your sauna comes with the optional MP3 shelf, use the two screws provided to mount the
self on either the side panels or front panel. (see figure 22)
Figure 22
Operating the Sauna
NOTE: Before the sauna is turned on, remove plastic protective covering from the CONTROL
PANELS. Please check and confirm that the connections to the POWER SUPPLY, HEAT EMITTERS,
CD/RADIO, and TEMPERATURE SENSOR are connected properly. The power supply voltage and
frequency must match the requested voltage and frequency of the sauna (120VAC 15AMP Dedicated
Circuit or 120VAC
20AMP Dedicated Circuit).
Since many materials absorb the infrared rays, minimal clothing is recommended for maximum effect.
The infrared sauna emitters are designed to heat you and not necessarily the air inside the sauna. It is
not a hot box like a traditional sauna. The temperature gauge is a guide for your safety. It is
recommended that you drink water before, during, and after sauna use to prevent dehydration since
body fluids will be lost through perspiration. It is not recommended to shower after use since the
pores in your skin will be open and could possibly absorb anything in the water.

16
1. Plug the sauna into the outlet receptacle.
2. Press the POWER button once. The POWER light will come on, the TIME DISPLAY will show 90
(minutes), the TEMPERATURE DISPLAY will show 66 (degrees Celsius), and the control panel will
flash.
3. Press the up/down arrows under the TIME DISPLAY to adjust the amount of time you want the sauna
to remain on. Press the C/F button to choose between Celsius and Fahrenheit. Press the up/down
arrows under the TEMPERATURE DISPLAY to adjust the temperature setting. Once you have set
these adjustments to the desired settings, press the START/WORK button. If you don’t press the
button for 5 seconds, the control panel will stop flashing and the set-up values will be memorized.
The WORK and HEAT lights will now be on and the emitters will now be generating heat. You will
need to pre-heat the sauna room to the set temperature before entering. Please keep in mind that
you will increase the time it takes for the sauna room to reach the set temperature if you enter the
sauna room before it has reached the set temperature.
4. During your sauna session, set-up time will count down the minutes one by one. When the time
remaining is 5 minutes, the buzzer will make a warning sound for approximately 15 seconds letting
you know you only have 5 minutes remaining. At this point, you can let the time run out or adjust the
time by pressing the up/down arrows under the TIME DISPLAY. If you do choose to adjust the time,
the control panel will flash and the emitters will stop generating heat. Once you set the time to the
desired setting, then press the START/WORK button twice and the control panel will stop flashing and
heat will began coming from the emitters once again.
5. Heating times do vary. Generally, it will take approximately twenty to thirty minutes to preheat the
sauna to 50 degrees Celsius / 122 degrees Fahrenheit. When the ambient temperature is low,
heating requires additional time. For the first few times of use, you may use 46 degrees Celsius /
115 degrees Fahrenheit as a reference starting point for a time period of about 15 minutes (this
represents the actual time you are in the sauna at the desired temperature). As you become more
comfortable and familiar with the sauna, you can increase the temperature and time period according
to personal preference.
6. When the temperature is at the set-up value, the digital control will maintain the set temperature.
The WORK light will remain on and the HEAT light will turn off. The emitters will stop generating
heat. Once the inside temperature drops approximately 4 degrees, the HEAT light will turn back on
and heat will again be generated by the emitters. With the digital control, the inside temperature will
always remain around the set-up value.
7. Reading lamps and/or roof lamps and/or color therapy lamps are operated by pressing the
respective buttons located towards the center of the control panel. These lamps are offered on
some models and are not available on all models.
8. Chromotherapy/ColorTherapy Lighting (optional) can be operated as follows. First, you
will need to install the battery. Once the battery has been inserted into the remote, you are ready
to operate the chromotherapy/color therapy lighting system. Press the READING LIGHT button on
the sauna control panel. The white light will come on. While pointing the remote at the ceiling
light, you can press any of the colors on the remote and that color will be displayed. You can use
the SHADE button on the remote to go through a sequence of colors. If you want to turn the light
off during your sauna session, you can press the POWER button on the remote. Please note: You
must be inside the sauna room for the remote to work. Remote may vary in appearance.

17
Control Panel (Standard)(Power Supply 1)
Power On/Off: Press to control the main power of the sauna
Power Indicator: Indicates the status of the sauna’s main power
Work Start/Stop: Press to control the working functions of the sauna
Work Indicator: Indicates the working status of the sauna
Heat Indicator: Indicates the status of heating function
Light: Press to control the lighting function
Time Display: Displays the heating time of the sauna in minutes
Time: Press to adjust the setting of the timer
Temperature Display: Displays the actual interior temperature of the sauna room in
0
C/
0
F
Temperature: Press to adjust the temperature setting
0C/0F: Press to change the temperature display between 0
C/
0
F
Control Panel (Optional) (Power Supply 2)
Power On/Off: Press to control the main power of the sauna
Power Indicator: Indicates the status of the sauna’s main power
Work Start/Stop: Press to control the working functions of the
sauna
Work Indicator: Indicates the working status of the sauna
Heat Indicator: Indicates the status of heating function
Light: Press to control the lighting function
Time Display: Displays the heating time of the sauna in minutes
Time: Press to adjust the setting of the timer
Temperature Display: Displays the actual interior temperature of the
sauna room in
0
C/
0
F
Temperature: Press to adjust the temperature setting
0C/0F: Press to change the temperature display between 0
C/
0
F
Bluetooth: Control panel can be connected to devices to play
music

18
1. Plug the sauna into the outlet receptacle.
2. Press the button once. The POWER light will come on, the TIME DISPLAY will show 90
(minutes), the TEMPERATURE DISPLAY will show 66 (degrees Celsius), and the control panel will
flash.
3. Press the button and then the up/down arrows to adjust the amount of time you want the
sauna to remain on. Press the C/F button to choose between Celsius and Fahrenheit. Press the
button and then the up/down arrows to adjust the temperature setting. Once you have set
these adjustments to the desired settings, press the button. You will need to pre-heat the
sauna room to the set temperature before entering. Please keep in mind that you will increase the
time it takes for the sauna room to reach the set temperature if you enter the sauna room before it
has reached the set temperature.
4. The set-up time will count downward in minutes one by one. The time will continue to count
downward unless you interrupt the time by pressing the clock button and then adjust the time to
your preference by pressing the up/down arrow buttons. Once again, you can adjust the time in
minutes by pressing the button and then the up/down arrows. If you do choose to adjust the
time, the control panel will flash and the emitters will stop generating heat. Once you set the time to
the desired setting, then press the button twice and the control panel will stop flashing and
heat will began coming from the emitters once again.
5. Heating times do vary. Generally, it will take approximately twenty to thirty minutes to preheat the
sauna to 50 degrees Celsius / 122 degrees Fahrenheit. When the ambient temperature is low,
heating requires additional time. For the first few times of use, you may use 46 degrees Celsius
/115 degrees Fahrenheit as a reference starting point for a time period of about 15 minutes (this
represents the actual time you are in the sauna at the desired temperature). As you become more
comfortable and familiar with the sauna, you can increase the temperature and time period
according to personal preference.
6. When the temperature is at the set-up value, the digital control will maintain the set temperature.
The emitters will stop generating heat. Once the inside temperature drops approximately 4
degrees, the heat will again be generated by the emitters. The inside temperature will always
remain around the set-up value.
7. Reading lamps and/or roof lamps and/or color therapy lamps are operated by pressing the
button located on the control panel. These lamps are offered on some models and are not
available on all models. When you press the button once, the interior light will come ON.
When you press the button twice, the interior light will turn OFF. When you press the
button three times, the interior white light and exterior white lights will come ON. When you press
the button four times, both the interior and exterior lights will turn OFF.
8. Chromotherapy/ColorTherapy Lighting (optional/not available on all models) can be
operated as follows. First, you will need to install the battery. Once the battery has been inserted
into the remote, you are ready to operate the chromotherapy/colortherapy lighting system. Press
the button on the sauna control panel. The white light will come on. While pointing the remote
at the ceiling light, you can press any of the colors on the remote and that color will be displayed.
You can use the SHADE button on the remote to go through a sequence of colors. If you want to
turn the light off during your sauna session, you can press the POWER button on the remote.
Please note: You must be inside the sauna room for the remote to work.