golmar 4/G2+ User manual

G2+ 2-wire installation
USER MANUAL
Kit Soul
Art 4 monitorLite
TECHNOLOGY
Cód. 50122625 TS5110 ART LITE E4 N REV.0122

SOUL S5110/ART 4 VIDEO DOOR ENTRY SYSTEM KITLITE 2
CONTENTS
Contents ....................................................................................................................................................................2
IMPORTANT IN THIS MANUAL ................................................................................................................................2
Recommendations.....................................................................................................................................................3
System operation .......................................................................................................................................................3
FA-G2+/ power supplyLITE ........................................................................................................................................4
Description ......................................................................................................................................................4
Installation .......................................................................................................................................................4
Soul panel 4.3- /LITE .............................................................................................................................................5 to 7
Description ......................................................................................................................................................5
Installation .......................................................................................................................................................6
Installation terminals ........................................................................................................................................6
Configuration switches.....................................................................................................................................7
Setting the audio level ......................................................................................................................................7
Art 4 /G2+ monitor ...................................................................................................................................... to 2LITE 8 3
Description ......................................................................................................................................................8
Installation .......................................................................................................................................................9
Installation terminals ........................................................................................................................................9
Configuration switches.....................................................................................................................................9
Main menu .....................................................................................................................................................10
Settings menu........................................................................................................................................1 to 11 3
Door panel call screen....................................................................................................................................14
Communication screen ..................................................................................................................................15
Image and communication settings........................................................................................................ to16 18
Timed 'do not disturb' menu....................................................................................................................19 to 21
Intercom menu.......................................................................................................................................22 to 23
Wiring diagrams............................................................................................................................................... to24 27
Cross sections and distances.........................................................................................................................24
One apartment with one access panel and one monitor ..................................................................................24
One apartment with two access panels and one monitor.................................................................................24
One apartment with up to two access panels and up to four monitors in cascade .............................................25
One apartment with up to two access panels and up to four monitors in distribution .........................................25
Connection of a lock release...........................................................................................................................26
Connection of an auxiliary device at the relay output .......................................................................................26
Connection of an output button.......................................................................................................................27
Connection of an external camera ..................................................................................................................27
Connection for an apartment door button........................................................................................................27
Special codes ..................................................................................................................................................28 to 29
Cleaning the monitor ................................................................................................................................................30
Cleaning the door panel............................................................................................................................................30
Notes .......................................................................................................................................................................31
Compliance..............................................................................................................................................................32
-This manual describes the new menu (with white background) of the ART 4 LITE G2+ monitor with version
V.04 and later.
- ART 4 LITE G2+ monitors with version and earlier refer to the quick guide supplied with the correspondingV.03
monitor.
IMPORTANT IN THIS MANUAL

3
SYSTEM OPERATION
RECOMMENDATIONS
- Preferably use a Golmar cable (2x1mm²).RAP-GTWIN/HF
- The wiring must run at least 40cm away from any other wiring.
- before making modifications to the device.Always disconnect the power supply
- The installation and handling of these devices must be carried out by authorised personnel.
- Check all connections before starting the device.
-Always follow the instructions contained in this manual.
To make a call, the visitor needs to press the door panel button: an audible tone indicates that the call is being made
and LED on the door panel illuminates.At this moment, the apartment's monitor(s) receive(s) the call.
In systems with two access doors, the other door panel automatically disconnects; if another visitor attempts to call, a
number of telephone tones will indicate that the system is busy and LED on the door panel will illuminate.
Upon receiving the call, the image will appear on the screen of the master monitor (and slave 1, if it exists) without the
visitor knowing and icon displayed on the screen will blink green. To view the image from slave monitors 2 or 3,
press one of the buttons of the monitor to display the image. If the call is not answered within 45 seconds, door panel
LED will turn off and the system will become free.
To establish communication, press the button below the off-the-hook icon shown on the screen. Door panel
wLED ill illuminate. Communication will last for 90 seconds or until the button below on-the-hook icon shown
on the screen is pressed. When communication has ended, door panel LED will turn off and the system will
become free.
To open door or activate auxiliary output of the door panel, press the button below the corresponding icon
displayed on the screen. A single press activates the lock release or auxiliary output for secondfor a 3 seconds 1 ,
and LED on the door panel illuminates.
Detailed operation of the monitor is described on pp. 8 to 23.
12
SOUL S5110/ART 4 VIDEO DOOR ENTRY SYSTEM KITLITE

4
FA-G2+/ POWER SUPPLYLITE
Description
Installation
The fitting and handling of the power supply must be carried out by authorised personnel in the absence of
electrical current.
Install the power supply in a dry, protected and ventilated location. Make sure that the vents are not obstructed.
Use a DIN 46277 rail for fastening ( elements).4
Note that current regulations stipulate that the power supply must be protected by a circuit breaker.
To prevent electric shock, do not remove the protective cover without first disconnecting the power supply. Replace
it once all connections have been made.
Connect the wires to the installation terminals following the instructions in the diagrams.
SOUL S5110/ART 4 VIDEO DOOR ENTRY SYSTEM KITLITE
C
A. Monitor Bus connection terminals.
B. Door panel Bus connection terminals.
C. Protective cover for the current input.
D. Current input connection terminals.
E. Detail of the current input terminals without
protective cover.
NL
BUS(M) BUS(PL)
DIN rail.
Fastening tab on the DIN rail.
DIN rail.
B
D
E
A

5
SOUL PANEL 4.3- /LITE
Description
A
B
C
F
E
D
J
I
G
J
G
H H
B
C
D
L
M M
K M
Q
O
O
P
I
N
T
K
R
S
A. System status icons:
Call in progress.
Communication established.
Lock release activated.
System busy.
B. System status indicator lights.
C. Ambient lighting sensor.
D. Night viewing lighting.
E. Protective polycarbonate.
F. Nameplate label.
G. Speaker grill.
H. Colour camera.
I. Call button(s).
J. Microphone hole.
K. Front fixing screw.
L. Illumination module.
M. Wall fixing hole (x3). Do not overtighten the
fixing screws.
N. Illumination module gasket.
O. Installation terminals.
P. Cable grommet.
Q. Illumination module connector.
R. Configuration switches.
S. Volume control potentiometer.
T. No function.
SOUL S5110/ART 4 VIDEO DOOR ENTRY SYSTEM KITLITE

6
Installation
The door panel has been designed to withstand diverse environmental conditions. It is however advisable to take
extra precautions to prolong its service life, such as locating it in a covered area.
For optimum image quality, avoid direct contact from light sources (sunshine, street lights, etc.).
For correct installation: (locate the top of the door panel at a height of 1.65m).
1. Remove the metal front piece of the door panel by loosening the bottom screw with the Allen key supplied. On
the back of the front piece, you will find the button personalisation label.
2. Remove the screws that secure the proximity reader.
3. Present the door panel to the wall, positioning the top at 1.65m. Pass the installation cables through the cable
grommet.
4. Drill three 6mm holes at the indicated points (M), see p. 5. Insert the plugs supplied and fix the door panel to the
wall using the screws supplied.
5. Connect the cables to the removable terminals following the instructions in the installation diagrams.
Before replacing the and closing the door panel, perform the necessary settings (illumination module address door
panel illumination module, audio level setting, etc.), as indicated throughout this manual. Make sure that the
gasket is properly fitted.
Installation terminals (O)
For ease of installation, the installation terminals are removable and supplied in a separate bag. Once the
terminals are wired, place them in position.
BUS BUS CV- CV+ AP+
C NA GND CCTV AP-
ON
1 2 3 4
BUS BUS, : communications bus (non-polarised).
CV CV-, +: lock release output 12Vdc (maximum 270mA).
AP AP+, -: remote activation button connection. Note: For correct
operation, the monitor's address 1 must be connected to
the Bus.
IMPORTANT: Installation with 2 access door panels and
AP button on both door panels, one of the door panels
must connect the AC lock release (instead of DC lock
release). SAR-12/24 required,
relay a TF-104 transformer&
see pages 24-25 and 26.
C, : potential-free relay output (maximum 6A/24V).NA
GND CCTV, : input for external analogue camera.
SOUL S5110/ART 4 VIDEO DOOR ENTRY SYSTEM KITLITE
SOUL PANEL 4.3- /LITE

7
Configuration switches (R)
Configuration changes should be made with the equipment turned off. If they are performed with the equipment
turned on, disconnect it for 10 seconds after any modification.
All switches are factory set to OFF.
Switch 1.
Defines the door panel address.
Switch 2, must be OFF.
OFF-OFF
OFF OFF-
O -OFFN
Door panel 1 Door panel 2
Apartment 1
Switches and must be OFF.3 4
Setting the audio level
If the audio volume on the door panel after starting up the device is not adequate, use the volume control
potentiometer (S). This setting affects the communication and confirmation tone audio level.
BUS BUS CV- CV+ AP+
C NA GND CCTV AP-
ON
1 2 3 4
ON
12 3 4
ON
12 3 4
ON
1 2 3 4
S
SOUL S5110/ART 4 VIDEO DOOR ENTRY SYSTEM KITLITE
SOUL PANEL 4.3- /LITE

8
ART 4 /G2+ MONITORLITE
Description
*
A. Speaker.
B. Function buttons, access and selection of menu
functions.
The function of each button is shown on the monitor
screen with an icon located just above each button
(see pp. 10 to 23).
Press to access 'Doctor mode' function (standby monitor):
- With the special code '0441' (Doctor mode) already
entered pp. 28 to(see 29), press the button for 1 sec. to
access the menu and activate/ deactivate the function.
- The push button led will blink in white color and the
icon if thewill be displayed in the main menu
function 'Doctor mode' is activated and it will turn off if
the function is deactivated.
C. LEDMonitor status :
Yellow ON: Standby without notification.
Red ON: “Do not disturb” Mode a tivated.c
D. 4.3" TFT colour screen.
E. Golmar use.
F. Microphone.
G. Raised dots for the visually impaired people.
In call :/communication
Above this raised dot is the 'Start/ nd communication'E
button.
Above these raised dots is the 'Door opening' button.
H. Wall mounting connector fixing (x4).
I. Configuration switches.
J. Installation terminals.
SOUL S5110/ART 4 VIDEO DOOR ENTRY SYSTEM KITLITE
A
D
B
CFE
G
H
I
J
H
H
H
SA
GND
HZ
HZ
ON
1 2 3 4 5 6 7 8
BUS
BUS
SA
OF F = 0
ON = 1
DIP 1 to 7
DIP 8
Mon tori
address
EOL
resi s tor
GND
HZ
HZ
BUS
BUS
128
codes

9
Installation
Avoid dusty or smoky environments or locations near sources of heat.
For proper installation, use the template supplied with the product.
1. Position the top of the template at a height of 1.65m.
2. If you are going to use an embedding box to pass the wiring through, make sure that it is in line with the holes
corresponding to the box model chosen and fix the connector. If you prefer to fix the connector directly to the
wall, make four 6mm holes at the points indicated (A), insert the wall plugs supplied and screw in the connector.
3. Pass the installation wires through the middle hole and connect them to the removable terminals as shown in the
wiring diagrams. Before connecting the removable terminals to the monitor, configure the switch as indicated
below.
4. Connect the removable terminals to the monitor and place the monitor in front of the connector, making sure the
fixings line up. Move the monitor downwards to secure it.
Installation terminals (J)
For ease of installation, the installation terminals are removable and supplied in a separate bag. Once the
terminals are wired, place them in position.
BUS, BUS: Communication BUS (non-polarised).
SA GND, :Auxiliary call repeater output (max 50mA/12V), relay SAR-12/24.
HZ HZ, : Apartment front door button input:
Connect only on the master monitor. The signal received is then transmitted to
the slave monitors in the same apartment through the BUS.
Configuration switches (I)
Switches 1 to 7.
These assign the address of the corresponding monitor to its call button on the door panel. Switches to must2 7
remain in the OFF position.
Apartment 1
Switch 8.
This activates the end-of-line resistance in the ON position. Activate it in monitors where the bus cable ends.
Deactivate it only in intermediate monitors.
Note:To define whether the monitor is master or slave, configure the corresponding special code:
"0550" Master (factory default), "0551" Slave 1, "0552" Slave 2 or "0553" Slave 3, (see pages 28-29).
Each apartment must have one master monitor, and only one.
SA
GND
HZ
HZ
ON
1 2 3 4 5 6 7 8
BUS
BUS
ON
1 2 3 4 5 6 7 8
SOUL S5110/ART 4 VIDEO DOOR ENTRY SYSTEM KITLITE
ART 4 /G2+ MONITORLITE
Note: HZ push button function mode: When HZ push button is pressed will be call tone and activate the output of
auxiliary call repeater with standby monitor call process m ation process HZ tone with lower audio level, , com unic ( ),
intercom .process and "Do not disturb" mode

10
Main menu
If the device is in standby (screen switched off), to access the main menu, press any of the buttons of the monitor.
Then press the button located just below the corresponding icon. The device will return to standby mode after 20
seconds without activity.
Press the button below icon to display the image from the door panel. Note: This enablesmaster
the door panel camera to be changed, the audio on the corresponding door panel to be activated
and the door to be opened (see p. ).14
Press the button below icon to access the menu of the intercom between other monitors in the
same apartment (see p. 2 ).2 to 23
Press the button below icon to make changes to the system settings (see pp. 1 -1 ).1 3
Press the button below icon to enable disable the 'Dofor 3 seconds and for 1 second to
not disturb' function: If the monitor is in 'Do not disturb' mode, the status LED will
illuminate (red) and the ringtone on the monitor will not sound when a call ( “HZ”see note
p g )a e 9 is received.
With the "Do not disturb" mode deactivated, a one-second press accesses the menu,
allowing you to set a "Do not disturb" mode time period (see pages 19 to 20) and set an
"Automatic door opening" mode time (see page 20 to 21).
Main menu
Disabled Enabled
SOUL S5110/ART 4 VIDEO DOOR ENTRY SYSTEM KITLITE
ART 4 /G2+ MONITORLITE
Press the button below icon to " " + &staircase light activation (SAR-G2 SAR-12/24 modules
required).
Note: New menu available with V.04 and later of ART 4 LITE G2+ monitors.

11
Settings menu
SOUL S5110/ART 4 VIDEO DOOR ENTRY SYSTEM KITLITE
ART 4 /G2+ MONITORLITE
Continued overleaf
Settings menu screen
Then press the button below icon to access the settings menu. If you wish to return to the main menu,
press the button below the icon .
Access settings menu screen
M menuain
Press the button below icon to access the settings menu screen.
Access settings menu screen
( )
*
Note: New menu available with V.04 and later of ART 4 LITE G2+ monitors.

12
Settings menu
SOUL S5110/ART 4 VIDEO DOOR ENTRY SYSTEM KITLITE
ART 4 /G2+ MONITORLITE
Continued overleaf
Continued from previous page.
The 'About' screen provides information about the monitor, such as the software version, address and
whether it is master or slave (M, S1, S2 or S3).
It enables updated versions of the manual to be downloaded to a mobile or tablet, for which it is
necessary to have a QR code scanner app installed.
It enables the monitor to be restored to factory settings, such as melodies, call volume, etc.
Press the button below icon to return to the settings menu.
To restore the monitor to factory settings, press the button below icon to access the factory reset
menu, then press the button below icon to perform this function. Press the button below icon
to return to the 'About' screen.
Press the button below icon to return to the settings menu.
FW
0 /01 M
2 1.0
‘About' screen
Settings menu screen
Settings menu screen
Returning to the main menu: Press the button below
icon to return to the main menu.
Note: New menu available with V.04 and later of ART 4 LITE G2+ monitors.

13
Settings menu
SOUL S5110/ART 4 VIDEO DOOR ENTRY SYSTEM KITLITE
ART 4 /G2+ MONITORLITE
Continued from previous page.
Option selection screen
Selecting the melody and call volume: Press the button below icon to access the settings screen.
In order to identify the origin of the calls when you are not in front of the monitor, select different
melodies and the desired call volume. Go to the option to be modified by pressing the buttons
below corresponding icons / , then press the buttons below corresponding icons / to
select the melodies and desired call volume. Press the button below icon to return to the
settings menu.
Important: KIT S5110 ART4 LITE.Door panels & have no use with
105 05
05
02
05
03
01
03
# #
2
3
4
Settings menu screen
# #
Press the button below icon to return to the main menu.
Settings menu screen Main menu
3 4
Note: New menu available with V.04 and later of ART 4 LITE G2+ monitors.

14
SOUL S5110/ART 4 VIDEO DOOR ENTRY SYSTEM KITLITE
ART 4 /G2+ MONITORLITE
Door panel call screen
Press the hidden button below icon to activate the lock release (or device connected to the CV
output of see pp. 28 to 29the door panel) for 3 seconds (factory setting, ).
P or device connected to the relayress the hidden button below icon to activate the lock release (
output 1 see pp. 28 to 29of the door panel) for second (factory setting, ).
1
2
This screen is displayed when receiving a call or pressing the button below icon of the main menu. During a call,
icon displayed on the screen green (during the call process). In the top of the screen, the sourceis in color left
of the image is displayed. The call has a duration of 45 seconds.
Press the button below icon / to start or end audio communication with the door panel
displayed respectively. Communication has a maximum duration of 90 seconds. Once
communication has ended, the screen will turn off.
1
2
Press the button below icon to change the source of the image as long as the system has more
than one door panel or has an external camera connected and display has been activated (see
pp. ). It is possible to make the change during display, call and communication processes.28 to 29
Press the button below icon for 3 seconds to access the image and monitor volumein call tone
settings menu. Select the option to be modified by pressing the buttons below corresponding
icons / , change to the desired level by pressing the buttons below corresponding icons /
and validate the changes made by pressing the button below icon , (ver pág. 16 to 18).
End the call tone on the monitor.
Press the button below icon staircase light activation (SAR-G2 SAR-12/24 modulesto " " + &
required). Note: Displayed on the screen during a call or communication process if the
function to change the source of the image is not activated by displaying the icon on the
screen instead.
2
12
1
Note: New menu available with V.04 and later of ART 4 LITE G2+ monitors.

15
Door panel call screen
SOUL S5110/ART 4 VIDEO DOOR ENTRY SYSTEM KITLITE
ART 4 /G2+ MONITORLITE
1
1
2
1
This screen is displayed during a communication process. During a , icon displayed on thecommunication
screen green In the top of the screen, the source of the image is displayed. The cis in color. left ommunication
has a duration of seconds.90
Press the hidden button below icon to activate the lock release (or device connected to the CV
output of see pp. 28 to 29the door panel) for 3 seconds (factory setting, ).
P or device connected to the relayress the hidden button below icon to activate the lock release (
output 1 see pp. 28 to 29of the door panel) for second (factory setting, ).
1
2
Press the button below icon / to start or end audio communication with the door panel
displayed respectively. Communication has a maximum duration of 90 seconds. Once
communication has ended, the screen will turn off.
1
2
Press the button below icon to change the source of the image as long as the system has more
than one door panel or has an external camera connected and display has been activated (see
pp. ). It is possible to make the change during display, call and communication processes.28 to 29
Press the button below icon for 3 seconds to access the image and monitor in communication volume
settings menu. Select the option to be modified by pressing the buttons below corresponding
icons / , change to the desired level by pressing the buttons below corresponding icons /
and validate the changes made by pressing the button below icon , (ver pág. 16 to 18).
Press the button below icon staircase light activation (SAR-G2 SAR-12/24 modulesto " " + &
required). Note: Displayed on the screen during a call or communication process if the
function to change the source of the image is not activated by displaying the icon on the
screen instead.
2
Note: New menu available with V.04 and later of ART 4 LITE G2+ monitors.

16
SOUL S5110/ART 4 VIDEO DOOR ENTRY SYSTEM KITLITE
ART 4 /G2+ MONITORLITE
Note: New menu available with V.04 and later of ART 4 LITE G2+ monitors.
During communication process , press the button below icon for 3a call process or during a(Screen A) (Screen B)
seconds to access the image and monitor in communication volume settings menu.call/
2
The following brightness control menu will then be displayed. Adjust to the desired level by pressing the buttons
below icons / . To access the contrast control, press the button below icon . To exit the image and
communication settings menu, press the button below icon .
Call process screen Communication process screen
Screen A Screen B
4
Press for
3 segundos
1
1
2
1
12
1
1
Press for
3 segundos
Image and communication settings
Continued overleaf

17
Image and communication settings
Continued overleaf
SOUL S5110/ART 4 VIDEO DOOR ENTRY SYSTEM KITLITE
ART 4 /G2+ MONITORLITE
The following contrast control menu will then be displayed. Adjust to the desired level by pressing the buttons
below icons / . To access the colour control, press the button below icon . To exit the image and
communication settings menu, press the button below icon .
The following colour control menu will then be displayed. Adjust to the desired level by pressing the buttons below
icons / . To access the monitor communication volume control, press the button below icon .call tone /
To exit the image and communication settings menu, press the button below icon .
1
4
1
4
Continued from previous page.
Note: New menu available with V.04 and later of ART 4 LITE G2+ monitors.

18
Image and communication settings
SOUL S5110/ART 4 VIDEO DOOR ENTRY SYSTEM KITLITE
ART 4 /G2+ MONITORLITE
Continued from previous page.
The following call tone settings volume during a call process or communication settings volume during(Screen A)
a communication process (Screen B) will then be displayed. Adjust to the desired level by pressing the buttons
below icons / . To return to the brightness control (carousel mode), press the button below icon .
Communication screen
To exit the image and communication settings menu, press the button below icon .call /
Call tone settings volume Communication settings volume
Screen A Screen B
Communication settings volume
Screen B
1
2
1
2
1
2
1
1
2
1
Note: New menu available with V.04 and later of ART 4 LITE G2+ monitors.

19
SOUL S5110/ART 4 VIDEO DOOR ENTRY SYSTEM KITLITE
ART 4 /G2+ MONITORLITE
Period of time for 'do not disturb' mode menú
Continued overleaf
'Do not disturb' mode settings: If the device is in standby (screen switched off), to access the main
menu, press any of the buttons of the monitor. Then press the button below icon to access the
settings screen.
Option selection screen
Main menu
To set a period of time for in which the monitor will not sound when receiving"Do not disturb" mode
calls (see note "HZ" page 9), go to the option with icon pressing the button below icon or
and select the option by pressing the button below icon Then you can set a period of time. (from
00h & 01 minute to 23h & 59 minutes) 'Do not disturb' modefor , by pressing corresponding
buttons / , validate the changes made by pressing the button below icon .and /
07 00
# #
07 00 08 30
# #
Time period setting screen
Option selection screen
Note: New menu available with V.04 and later of ART 4 LITE G2+ monitors.

20
Period of time for 'do not disturb' mode menú
SOUL S5110/ART 4 VIDEO DOOR ENTRY SYSTEM KITLITE
ART 4 /G2+ MONITORLITE
Continued overleaf
Main menu
Press the button below icon to return to the main menu. If the 'Do not disturb' mode is enable (see
pages 19 to 20) will be shown the icon in the main menu and the m LED will turn ononitor status
(red color).
Option selection screen
08 30
07 00
This selection is unused. (Factory default this function is deactivated).
”Automatic door openning”: This selection is visible in the “Do Not Disturb”settings menu, with the special
code '0441' (Doctor mode) already entered in the monitor (see specialfor automatic door opening
codes pp. 28 to 29). In standby monitor, you can also access the menu by pressing the pushNote:
button....... (blinking in white color) on the monitor.
1
Option selection screen
07 00
07 00
Note: New menu available with V.04 and later of ART 4 LITE G2+ monitors.
Continued from previous page.