golmar VESTA SE GB2 User manual

Code 50120514 TVESTA SE G 2 EN2 B REV.0119
VESTA SE GB2 M2 ONITOR
USER MANUAL
TECHNOLOGY
Camera/Door
Main menu
Do not disturb
Intercom function
Image memory

INTRODUCTION
First of all, we thank and congratulate you for purchasing this product.
Our commitment to achieving the satisfaction of customers like you is manifested through our ISO-9001 certification
and the manufacture of products like the one you have just purchased.
Its advanced technology and strict quality control will ensure that customers and users enjoy the numerous features
that this device offers. To get the most out of them and ensure proper operation from day one, we recommend that you
read this instruction manual.
CONTENTS
2
SAFETY PRECAUTIONS
-Avoid overtightening the screws of the monitor's wall mounting connector.
-Always disconnect the power supply before installing or making modifications to the device.
-The fitting and handling of these devices must be carried out by authorised personnel.
-All of the wiring must run at least 40cm away from any other wiring.
-Install the monitor in a dry protected location free from the risk of dripping or splashing water.
-Do not place in humid, dusty or smoky locations, or near sources of heat.
-Before connecting the device to the mains, check the connections between the door panel, power supply, distributors
and monitors.
-Always follow the instructions contained in this manual.
Introduc n................................................................................................................................................................... 2tio .
Contents........................................................................................................................................................................2.
Safety precautions........................................................................................................................................... .2............. .
Characteristics.............................................................................................................................................................. 3.
System operation......................................................................................................................................... ..3................ .
Description of the monitor.................................................................................................................................................
..................................................................................................................................................................4
Description
........................................................................................................................... ..... 4......... .Function and menu buttons
............................................................................................................................................................ 4....Status LEDS
........................................................................................................................................ ...... 4.... .Connection terminals
............................................................................................................................... . 4................................. ...DIP switch
........................................................................................................... 5..................Setting the monitor's address codes
Installing the monitor in a wall mounting connector......................................................................................................... 6.
Installing the monitor in an embedding box.................................................................................................................... 7..
Operation.............................................................................................................................................................. ...........
..................................................................................................................................................................8
Description
1.1 ...................................................................................................................... 8..Receiving a call from the door panel
1.2 ......................................................................................................... .9....................Call not answered (missed call)
1.3 ............................................................................................................................9Ending a call from the door panel
1.4 ...................................................................................................................... 9.Answering a call from the door panel
1. .............5 10.Answering a call from the door panel (activating light SAR-GB2 and displaying cameras DQ-CAM-GB2)
1. ...................................................................................... 106 ............'Doctor mode' function (automatic door opening)
Screen and monitor volume settings menu (contrast, brightness, colour and monitor volume)...................................... 11.
User menu........................................................................................................................................................... ............
................................................................................................................................................ .12. .
Accessing the menu
1. ................................................................................................................. 13...Displaying door panel/camera images
1.1 ...............................................................................................................13.Displaying images from the door panels
1.2 ............................................................... 14.Displaying images from the cameras (DQ-CAM-GB2 module required)
2. ................................................................................................................................................. .15. .Intercom function
2.1 ................................................................................................................ 15-16.Intercom calls between apartments
2.2 ................................................................................................. 16.Intercom 'dial' between apartments (no function)
2. ........................................................................................................................... 173 .Calling the surveillance monitor
2. ........................................................................................................... .184 .Intercom calls within the same apartment
3. ...................................................................................................................................................... 19.Image memory
. .......................................................................................................................................... -24 20 1Do not disturb mode
. .............................................................................................................. 215 ....................Divert call mode (no function)
6. .................................................................................................................................... 22.Turning on the outside light
. ..................................... 2 -27 .............. 3 5.Settings (ringtone, ring volume, auto switch-on time and language selection)
. ................................................... ..... 2 -28 . 5 6About (information, 'restore' default setting and access to installer menu)
Cleaning the monitor....................................................................................................................................................27
VESTA2 SE GB2 MONITOR

CHARACTERISTICS
-Hands-free monitor.
-4.3” TFT colour screen.
-Monitor with simple installation (non-polarised 2 wire BUS).
-The VESTA2 SE GB2/H monitor interacts with hearing aids equipped with T-mode, making conversation between
apartment and door panel easier.
-Capacitive buttons to access and select menu functions:
User menu:
-Displaying door panel images.
-Displaying camera pictures (DQ-CAM-GB2 module required).
-Intercom calls between apartments.
-Calling the surveillance monitor.
-Intercom calls within the same apartment.
-Image memory (M-IP GB2 module required).
-Do not disturb mode (door panel and intercom calls are not received).
-Call divert (no function).
-Activating the outside light (SAR-GB2 module required).
-Settings: Ringtone, ring volume, auto switch-on time and language.
-About: Information, 'restore' default setting and access to installer menu.
Installer menu:
-Monitor as master or slave 1, slave 2 or slave 3. Up to 4 monitors per apartment.
-Surveillance monitor.
-Enabling the menu to be viewed when the Bus is busy.
-Activating intercom between apartments.
-Activating doctor mode (automatic door opening).
Screen and volume settings menu: (during auto switch-on or communication).
-Contrast, brightness, colour and volume of the monitor speaker.
-Start/stop communication button and, in standby mode, it displays the image from the door panel.
- /Door release 1 and 2 activation buttons respectively.
-'Doctor mode' function (automatic door opening).
- .Power status LED
-'Do not disturb' mode - LED fixed/'Doctor mode' - LED slow blink.
-Different ringtones to identify the origin of the call (door panel, intercom or apartment door).
-DIP switches for setting the monitor address (call code) and end of line.
-Input for call from the apartment door.
-SAR-12/24 call repeater output (12Vdc/50mAmaximum).
SYSTEM OPERATION
-To make a call, the visitor must press the button of the apartment; an audible sound indicates that the call is being
made and LED will turn on. If vocal synthesis is enabled, a 'Call is in progress' message appears indicating that a
call is being made. At this moment, the apartment's monitor receives the call. If another apartment is called by
mistake, press the button for the correct apartment and the first call will be cancelled.
-The call lasts for 40 seconds and, when received, the image appears on the master monitor without the visitor
knowing. To view the image on a slave monitor, this function needs to have been enabled on the monitor. House kit
application: the image appears on the monitor (with code 0 'house 1' or monitor with code 16 if the call is in 'house 2')
when receiving the call without the visitor being alerted.
If the call is not answered within 40 seconds, LED will turn off and the channel will be freed.
-To establish communication, press button of the monitor and LED of the door panel will turn on. If the monitor is
a Vesta2 SE GB2/H with icon on the front, make sure that the hearing aid is between 15 and 25 cm away from the
monitor to ensure maximum audio quality during communication with the door panel.
-Communication will last for one and a half minutes or until button is pressed again. When communication has
finished, LEDs and will turn off and the channel will be freed. If vocal synthesis is enabled, a 'Communication is
finished' message will indicate that the call is over.
-To open door 1 or 2, press the corresponding button / during the call or communication processes: one press
will activate the lock release for five seconds and LED will also turn on for five seconds. If vocal synthesis is enabled,
a 'Door open' message will be indicated on the door panel.
-Adescription of the function buttons can be found on page 4.
3
VESTA2 SE GB2 MONITOR

DESCRIPTION OF THE MONITOR
Connection terminals and DIP switch:
( ):WHITE HZ+
( ):GREEN HZ-
Connection terminals:
L1, L2:Bus connection (non-polarised).
HZ+, HZ-: Door bell connection.
SONERÍA, GND:Call repeater connection (SAR-12/24).
(12Vdc/50mAmaximum).
Configuration DIP switch:
DIP 6: Configures the end of line. Leave in the ON position in monitors
where the bus cable terminates. Set to OFF in intermediate monitors
only.
DIP 1 to DIP 5: To set the monitor address (addresses 0 to 31).
The switches set to OFF have a zero value.
The values of the switches set to ON are shown in the table below.
The monitor code is the sum of the values of the switches set to ON.
(R ):ED CALL REPEATER
( ):BLACK GND
( ):YELLOW DO NOT USE
Menu access and function selection button.
Menu back button.
Power .status LED
Button: End call/communication.
In standby: Enter/exit menu mode.
'Do not disturb' function access button.
LED on: 'do not disturb' mode activated.
LED blinking: 'doctor mode' activated.
LED off: function not activated.
Menu buttons and status LEDs:
4
123
ON DIP
4 5 6
E : 0 + 0+4+0+16 = 20xample
Switch number: 1 2 3 4 5
Value when ON: 1 2 4 8 16
Table of values
Menu scroll down button.
In auto switch-on, call or communication: activates the outside light.
Menu scroll up button.
In auto switch-on, call or communication: selects from the door
panel camera(s) in ascending mode and in carousel (if any).
a. Microphone.
b. Communication with hearing aids (Vesta2 SE GB2/H).
Set the hearing aid switch to the T position, see page 8.
c. 4.3” TFT colour screen.
d. Open/close menu button.
e. Menu buttons.
f. Function button door 2 activation.
In standby: 'Do not disturb' button/indicator and 'doctor mode' indicator.
g. Marks for people with a visual disability.
h.Function button start/stop communication.
In standby: Display door panel image.
i. Function button door 1 activation.
In standby: Pres s for 1 0 seconds t o
activate/deactivate the 'doctor mode' function
(function code [9018] must be activated)
j. Connector fixings
k. Horizontal cable entry.
l. Connector.
m. DIP switch.
n. Bus connection terminals.
m
l
123
ON DIP
456
c
d
h
e
i
a
f
b
n
g
j
k
j
1 2 3
ON DIP
4 5 6
L1 L2
1 2 3
ON DIP
456
VESTA2 SE GB2 MONITOR

5
DESCRIPTION OF THE MONITOR
Setting the monitor's address codes (addresses 0 to 31):
DIP 6: Configures the end of line. Leave in the ON position in monitors where the bus cable terminates. Set to OFF in
intermediate monitors only.
123
ON DIP
4 5 6
C 00ode
123
ON DIP
4 5 6
Co 01de
123
ON DIP
4 5 6
C 02ode
123
ON DIP
4 5 6
C 03ode
123
ON DIP
4 5 6
C 04ode
123
ON DIP
4 5 6
C 05ode
123
ON DIP
4 5 6
C 06ode
123
ON DIP
4 5 6
C 07ode
123
ON DIP
4 5 6
C 08ode
123
ON DIP
4 5 6
Co 09de
123
ON DIP
4 5 6
C 10ode
123
ON DIP
4 5 6
C 11ode
123
ON DIP
4 5 6
C 12ode
123
ON DIP
4 5 6
C 13ode
123
ON DIP
4 5 6
C 14ode
123
ON DIP
4 5 6
C 15ode
123
ON DIP
4 5 6
C 16ode
123
ON DIP
4 5 6
C 17ode
123
ON DIP
4 5 6
C 18ode
123
ON DIP
4 5 6
C 19ode
123
ON DIP
4 5 6
C 20ode
123
ON DIP
4 5 6
C 21ode
123
ON DIP
4 5 6
C 22ode
123
ON DIP
4 5 6
C 23ode
123
ON DIP
4 5 6
C 24ode
123
ON DIP
4 5 6
C 25ode
123
ON DIP
4 5 6
C 26ode
123
ON DIP
4 5 6
C 27ode
123
ON DIP
4 5 6
C 28ode
123
ON DIP
4 5 6
C 29ode
123
ON DIP
4 5 6
C 30ode
123
ON DIP
4 5 6
C 31ode
DIP 1 to DIP 5: To set the monitor address (addresses 0 to 31).
123
ON DIP
4 5 6
Dip6 ONto Dip6 OFFto
123
ON DIP
4 5 6
VESTA2 SE GB2 MONITOR

INSTALLING THE MONITOR IN A WALL MOUNTING CONNECTOR
The top of the connector must be positioned at a height of 1.60m. The minimum distance between the sides of the
connector and the closest object must be 5cm.
Positioning the wall mounting connector:
Fix the monitor's wall mounting connector to the wall by drilling two 6mm diameter holes and using the screws and plugs
supplied with the monitor.
Fixing the monitor's wall mounting connector to the wall:
Positioning the monitor:
1 2 3
Avoid dusty or smoky environments or locations near sources of heat.
6
Connect the cables to the monitor (see p. 4), position the monitor in front of the wall mounting connector, ensuring that the
holes in the base of the monitor line up with those on the connector , and then move the monitor downwards until
the monitor is securely fixed to the connector .
Remember to remove the protective covering from the front of the monitor once installation is complete.
12
3
1 6. 0m
VESTA2 SE GB2 MONITOR
x4 30

INSTALLING THE MONITOR IN AN EMBEDDING BOX
Make a hole in the wall to position the top of the universal embedding box at a height of 1.60 m from the ground. The
minimum distance between the sides of the embedding box and the closest object must be 5cm.
Location of the embedding box:
1 6. 0m
Pass the cable through the hole made in the embedding box. Embed the box and ensure that it is level and flush.
Fix the wall mounting connector of the monitor to the embedding box with the screws supplied.
Positioning the embedding box and fitting the wall mounting connector:
Positioning the monitor:
Avoid dusty or smoky environments or locations near sources of heat.
7
1 2 3
VESTA2 SE GB2 MONITOR
Screws supplied with the
embedding box.
Connect the cables to the monitor (see p. 4), position the monitor in front of the wall mounting connector, ensuring that the
holes in the base of the monitor line up with those on the connector , and then move the monitor downwards until
the monitor is securely fixed to the connector .
Remember to remove the protective covering from the front of the monitor once installation is complete.
12
3

OPERATION
When a call is received, the monitor(s) will play a melody and show the door panel image on the master monitor without
alerting the visitor. If the call is not answered within 40 seconds the monitor returns to standby mode. If there is an M-IP
GB2 memory module, it will automatically take a photo or record video (for video, a 16GB Class 10 MicroSD card is
required, ) and status LED will blink indicating that a photo/video is pending viewing.not supplied
1.1 Receiving a call from the door panel:
Monitor description when receiving a call and during communication:
Door panel that made the call.
End call/communication.
Door 1 activated.
Activate lock release 1.
Start/stop communication.
8
Continued overleaf
Call/communication time elapsed.
1
DS-1
00:30
2Record
Door 2 activated.
Communication activated.
00:30
DS-1
VESTA2 SE GB2 MONITOR
Activate lock release 2.
Outside light activated (SAR-GB2 required).
Recording activated (M-IP GB2 memory module required).
Display cameras (DQ-CAM-GB2 required).
Activate outside light (SAR-GB2 required).
To open door 1, press the door release button
during the call: one press will activate the lock
release for 5 seconds.
To open door 2, press the door release button
during the call: one press will activate the lock
release for 5 seconds.
T
Communication with hearing aid (Vesta2 SE GB2/H monitor only):
Make sure that the hearing aid is 15-25 cm away from the
monitor to ensure maximum audio quality during
communication with the door panel.

OPERATION
When a call is received, the monitor(s) will play a melody and show the door panel image on the master monitor without
alerting the visitor. If there is an M-IP GB2 memory module, it will automatically take a photo or record video (for video,
a 16GB Class 10 MicroSD card is required, ) and status LED will blink indicating that a photo/video isnot supplied
pending viewing. To end the call, press button .
1.3 Ending a call from the door panel:
Continued from previous page.
1.2 Call not answered (missed call):
When a call is received, the monitor(s) will play a melody and show the door panel image on the master monitor without
alerting the visitor. If the call is not answered within 40 seconds the monitor returns to standby mode. If there is an M-IP
GB2 memory module, it will automatically take a photo or record video (for video, a 16GB Class 10 MicroSD card is
required, ) and status LED will blink indicating that a photo/video is pending viewing.not supplied
To open door 1, press the door release button
during the call: one press will activate the lock
release for 5 seconds.
9
00:30
DS-1
00:30
DS-1
1.4 Answering a call from the door panel:
When a call is received, the monitor(s) will play a melody and show the door panel image on the master monitor without
alerting the visitor. If there is an M-IP GB2 memory module, it will automatically take a photo or record video (for video, a
16GB Class 10 MicroSD card is required, ) and status LED will blink indicating that a photo/video isnot supplied
pending viewing. To answer the call, press button . If the monitor is a Vesta2 SE GB2/H with icon on the front,
make sure that the hearing aid is between 15 and 25 cm away from the monitor to ensure maximum audio quality during
communication with the door panel.
Communication will last for one and a half minutes or until button is pressed again.
Start/stop communication.
00:30
DS-1
Continued overleaf
VESTA2 SE GB2 MONITOR
To open door 2, press the door release
button during the call: one press will activate
the lock release for 5 seconds.
To open door 1, press the door release button
during communication or call processes: one
press will activate the lock release for 5
seconds.
To open door 2, press the door release button
during communication or call processes: one
press will activate the lock release for 5
seconds.

OPERATION
Continued from previous page.
1.6 'Doctor mode' function (automatic door opening):
Description:
The 'doctor mode' function enables lock release 1 to be activated automatically 7 seconds after making a call from the
door panel without having to establish communication or press door release 1 button . The main monitor will
display the door panel image without alerting the visitor. The call ends after 40 seconds and the channel is free. If there
is an M-IP GB2 memory module, it will automatically take a photo or record video 6 seconds after receiving a call from
the door panel (for video, a 16GB Class 10 MicroSD card is required, ) and status LED will blinknot supplied
indicating that a photo/video is pending viewing.
10
Enabling 'doctor mode':
To enable doctor mode, enter function code [9018] in the installer menu (see pp. 25-26).
Activating 'doctor mode':
To activate doctor mode, the monitor must be in standby mode. Then press button for 10 seconds. Status
LED will blink to indicate that the doctor mode function is activated.
Deactivating 'doctor mode':
To deactivate doctor mode, the monitor must be in standby mode. Then press button for 10 seconds. Status
LED will turn off to indicate that the doctor mode function is deactivated.
Important:
When activating 'do not disturb' mode (with the monitor's 'doctor mode' activated), the status LED will change from
blinking to fixed and the 'doctor mode' function will be cancelled.
When deactivating 'do not disturb' mode (with the monitor's 'doctor mode' activated), the status LED will blink and the
'doctor mode' function will be reactivated.
Installer menu
[ ]
9018
VESTA2 SE GB2 MONITOR
1.5 Answering a call from the door panel (activating light SAR-GB2 and displaying cameras DQ-CAM-GB2):
When a call is received, the monitor(s) will play a melody and show the door panel image on the master monitor without
alerting the visitor. If there is an M-IP GB2 memory module, it will automatically take a photo or record video (for video, a
16GB Class 10 MicroSD card is required, ) and status LED will blink indicating that a photo/video isnot supplied
pending viewing. To answer the call, press button . If the monitor is a Vesta2 SE GB2/H with icon on the front,
make sure that the hearing aid is between 15 and 25 cm away from the monitor to ensure maximum audio quality during
communication with the door panel.
Communication will last for one and a half minutes or until button is pressed again.
Start/stop communication.
00:30
DS-1
To open door 1, press the door release button during
communication or call processes: one press will activate the
lock release for 5 seconds.
To open door 2, press the door release button during
communication or call processes: one press will activate
the lock release for 5 seconds.
In auto switch-on, call or communication: activates the outside light (SAR-GB2 module required).
In auto switch-on, call or communication: selects from the door panel the image of the camera(s) in ascending
mode and in carousel (DQ-CAM-GB2 required). Viewing the image of the door panel or camera(s) fromNote:
the monitor enables the opening of door 1/2 and audio with the door panel in case of communication.

MONITOR SCREEN AND VOLUME SETTINGS MENU
11
To adjust the contrast, the monitor must be in communication or auto switch-on mode. Then press button to
display the 'Contrast' option on screen. Using menu buttons and , select the required contrast level. Press
button to change the next option 'Brightness' or press to exit the settings menu.
00:30
DS-1
Contrast: 5
To adjust brightness, the monitor must be in communication or auto switch-on mode. Then press
button repeatedly until option 'Brightness' is displayed on screen. Using menu buttons and , select the
required brightness level. Press button to change the next option 'Colour' or press to exit the settings menu.
00:30
DS-1
Brightness: 5
To adjust the colour, the monitor must be in communication or auto switch-on mode. Then press button repeatedly
until option 'Colour' is displayed on screen. Using menu buttons and , select the required colour level. Press
button to change the next option 'Volume' or press to exit the settings menu.
00:30
DS-1
Colo r: 5u
To adjust the communication volume, the monitor must be in communication or auto switch-on mode. Then press
button repeatedly until option 'Volume' is displayed on screen. Using menu buttons and , select the required
volume level. Press button to return to option 'Brightness' or press to exit the settings menu.
00:30
DS-1
Volume: 6
VESTA2 SE GB2 MONITOR

USER MENU
To access the menu, the monitor must be in standby. Then press menu button to display the first options screen
of the main menu.
Use menu buttons and to scroll through the different options and access the second screen of the main menu.
12
Continued overleaf
1st menu screen
2nd menu screen
1st menu screen
Main menu
Intercom function
Image memory
Do not disturb
Camera Door/
Description of the menu buttons:
Menu access and function selection button.
Menu back button.
Menu scroll down button.
Menu scroll up button.
Divert
Light
Settings
About
Main menu
Intercom function
Image memory
Do not disturb
Camera Door/
Main menu
Intercom function
Image memory
Do not disturb
Camera Door/
Main menu
VESTA2 SE GB2 MONITOR
Status LED:
Fixed: power On.
Blinking: Pending viewing of photos/videos of
door panel calls (if there is an M-IP-GB2
module, to record videos, a 16GB Class 10
MicroSD card is required, ).not supplied
Button:
Status LED blinking: Press to access the 'Image
memory' menu.
Status LED fixed: Enter/exit menu mode.
Note: The monitor takes a photo or makes an automatic video recording 6 seconds after receiving a call from the
door panel.
*
*
Main menu
Intercom function

USER MENU
13
1. Displaying door panel/camera images:
Selection screen
1st menu screen
1.1 To display the image from one of the installed door panels, use buttons and to go to option 'Camera/Door'
and press button . The following selection screen will be displayed. Go to the option corresponding to door panel
'Door' whose image needs to be displayed.
The following screen will display the image from the selected door panel with address 1, it will also indicate the selected
door panel 'DS-1' and the elapsed connection time.
The connection will last for 30 seconds or until option is pressed.
So establish audio and video communication with the selected door panel, press button . The screen will display
symbol . If the monitor is a Vesta2 SE GB2/H with icon on the front, make sure that the hearing aid is between
15 and 25 cm away from the monitor to ensure maximum audio quality during communication with the door panel.
Communication will last for one and a half minutes or until button is pressed again or option is pressed.
To open door 1 or 2, press the corresponding button / during the image display or communication processes: one
press will activate the lock release for 5 seconds.
00:30
DS-1
This symbol is only displayed in communication activated mode.
Continued overleaf
Main menu
Intercom function
Image memory
Do not disturb
Camera Door/
Continued from previous page.
VESTA2 SE GB2 MONITOR
00:30
DS-1
Door 1
Door 2
Door 3
Door 4
Selec

USER MENU
14
Selection screen
1ª Pantalla de menú
1.2 To display the image from one of the installed cameras (DQ-CAM-GB2 module required), use buttons
and to go to option 'Camera/Door' and press button . The following selection screen will be displayed.
Use buttons and to go to the option corresponding to camera 'Camera' whose image needs to be displayed.
The following screen will then display the picture from the camera selected with address 1, indicating the camera
selected 'CM-1' and the connection time elapsed.
The connection will last for 30 seconds or until option is pressed.
00:30
CM-1
Continued from previous page.
Select
C 1amera
Camera 2
Camera 3
Camera 4
Main menu
Intercom function
Image memory
Do not disturb
Camera Door/
1st menu screen
Continued overleaf
VESTA2 SE GB2 MONITOR

USER MENU
15
2. Intercom function:
Selection screen
1st menu screen
2.1 To access the intercom calls between apartments function, use buttons and to go to option 'Residents List'
and press button . The following selection screen will be displayed. Use buttons and to select the apartment to
call.
IMPORTANT: Activate function codes and on the monitor (see 'Installer menu' pp. 25-26).[9015] [8017]
Use buttons and to go to option 'Intercom' and press button . The following selection screen will be displayed.
Making an intercom call
Selection screen
Then press button to make the call. The following call screen will be displayed indicating the address of the apartment
to call. A long audible tone will confirm that the call is being made or a series of short audible tones will indicate that the
unit called is in communication with the door panel or on an intercom call with another apartment, and the call will not be
made. If a call is being made, press option to cancel the call.
'Residents List' selection screen
[01]
[02]
Residents list
[00]
[03]
'Residents List' selection screen
[01]
[02]
Residents list
[00]
[03]
P ...lease wait
01
Continued overleaf
Main menu
Camera Door/
Intercom function
Image memory
Do not disturb
Continued from previous page.
VESTA2 SE GB2 MONITOR
Dial
Call guard unit
Select
Residents list
Inner call
Dial
Call guard unit
Select
Residents list
Inner call

USER MENU
16
Continued from previous page.
In the called apartment, the monitor(s) will emit a melody indicating an intercom call and display the address of the
apartment making the call. Press button to accept the call and establish communication or press option to
cancel it. If the call is accepted, communication will last for one and a half minutes or until button is pressed again
or option is pressed.
Receive an intercom call In communication
If during the intercom process a call is received from the door panel of another apartment, the intercom process will be
cancelled; the monitor in the apartment will emit a melody to indicate that the call is being made and the image will
appear on the master monitor. To establish communication with the door panel, press button on the monitor. If
there are slave monitors in the apartment, press button on any of them.
The ringtones vary depending on where the call is being made from, enabling the user to identify its origin.
00 00
Continued overleaf
VESTA2 SE GB2 MONITOR
2.2 To access the dial function (no function).
Selection screen
Call guard unit
Select
Residents list
Inner call
Dial

2.3 To make a call to the building's surveillance monitor (if any), use buttons and to go to option 'Call Guard Unit'
and press button . The following call screen will be displayed indicating the address 'GU' of the surveillance monitor
to be called. A long audible tone will confirm that the call is being made or a series of short audible tones will indicate that
the surveillance monitor is in communication with another apartment, and the call will not be made. If a call is being
made, press option to cancel the call.
IMPORTANT: It is recommended to activate function code [8017] on the monitor (see 'installer menu' on pp. 25-26).
In communication
Selection screen
On the surveillance monitor, a melody will indicate the presence of a call and the address of the apartment making the
call. Press button to accept the call and establish communication or press option to cancel it. If the call is
accepted, communication will last for one and a half minutes or until button is pressed again or option is
pressed.
Make an intercom call
Receive an intercom call
USER MENU
17
Continued from previous page.
P ...lease wait
GU
If an apartment receives a call from the door panel while calling or communicating with the surveillance monitor, the call
to or communication with the surveillance monitor will be cancelled. The apartment's monitor will emit a melody
notifying the call from the door panel and the image will appear on the master monitor. To establish communication
with the door panel, press button on the monitor. If there are slave monitors in the apartment, press button on
any of them.
The ringtones vary depending on where the call is being made from, enabling the user to identify its origin.
00 00
Continued overleaf
VESTA2 SE GB2 MONITOR
Dial
Select
Residents list
Inner call
Call guard unit

USER MENU
18
Continued from previous page.
Continued overleaf
2.4 To access the intercom calls within an apartment function, use buttons and to go to option 'Inner call' and
press button . The following call screen will be displayed, a long audible tone will confirm that the call is being
made or short tones will indicate that a monitor in the apartment is already communicating with the door panel and the
call will not be made. If a call is being made, press option to cancel the call.
IMPORTANT: It is recommended to activate function code [8017] on the monitor (see 'installer menu' on pp. 25-26).
In communication
Selection screen
A melody coming from the rest of the monitors in the apartment indicates an incoming intercom call. Press button to
accept the call and establish communication or press option to cancel it. If the call is accepted, communication will
last for one and a half minutes or until button is pressed again or option is pressed.
Make an intercom call
Receive an intercom call
P ...lease wait
If a call is received from the door panel during the intercom process, the intercom call will be cancelled; a melody on the
apartment's monitor will warn that a call is being made and an image will appear on the master monitor. To establish
communication with the door panel, press button on the monitor. If there are slave monitors in the apartment,
press button on any of them.
If during the intercom process a call is received from another apartment, the intercom process will be cancelled; the
monitor in the apartment will emit a melody to indicate that the call is being made and the address of the apartment
making the intercom call will be displayed (see 'Intercom between apartments' on p. 15).
The ringtones vary depending on where the call is being made from, enabling the user to identify its origin.
VESTA2 SE GB2 MONITOR
Dial
Select
Residents list
Inner call
Call guard unit
00 00

USER MENU
19
Continued from previous page.
VESTA2 SE GB2 MONITOR
Selection screen1st menu screen
To view photos/videos of door panel calls, use buttons and to go to option 'Image memory' and press button .
The following selection screen will be displayed. Use buttons and to select the photo/video to view (for video, a
16GB Class 10 MicroSD card is required, , each video is 10 seconds long).not supplied
Main menu
Camera Door/
Intercom function
Image memory
Do not disturb
1 / /0 1 : : 18 11 7 0 52 0
To exit the 'Image memory' option and return to the 1st menu screen, press button .
Selection screen
To delete the selected photo/video, press button . The message ' ' will be displayed on the screen. PressDelete?
button to confirm the deletion and show the next saved photo/video or press option to cancel the deletion and
return to the 1st menu screen.
Selection screen
Delete?
0032 [1/ ] 181107_105210.avi20
1 / /0 1 : : 18 11 7 0 52 0
0032 [1/ ] 181107_105210.avi20
1 / /0 1 : : 18 11 7 0 52 0
0032 [1/ ] 181107_105210.avi20
1 / /0 1 : : 18 11 7 0 52 0
0032 [1/ ] 181107_105210.avi20
3. Image memory (M-IP-GB2 module required):
To change the time and date, go to the 'Settings' option (as shown on p. 23) and then press button for 3 seconds.
The following 'Date & Time' settings screen will be displayed. Press button to move over the date/time setting and
use buttons and to change the values. Press option to save and then press option to exit the user menu
function.
Date and time settings screen
Ring volume
Auto switch-on time
Ringtone
Settings
Language
Settings selection screen
10 : 51 : 40
201 - - 08 11 8
Date and time

4. Do not disturb mode:
Selection screen
1st menu screen
4.1 To activate do not disturb mode, use buttons and to go to the 'Always' option and press button . Status
LED will turn on and icon will be displayed on the menu screen indicating that the function has been activated.
The monitor will not receive door panel or intercom calls. To deactivate do not disturb mode, see section '4.4 To
deactivate do not disturb mode' on p. 21.
Use buttons and to go to the 'Do not disturb' option and press button . The following selection screen will be
displayed.
Main menu
Camera Door/
Intercom function
Image memory
Do not disturb
USER MENU
20
For our1 h
For ours8 h
Normal
Do not disturb
Always
Selection screen
For 1 ourh
For ours8 h
Normal
Do not disturb
Always
Continued overleaf
4.2 To activate do not disturb mode for '1 hour', use buttons and to go to the '1 hour' option and press button .
Status LED will turn on and icon will be displayed on the menu screen indicating that the function has been
activated. The monitor will not receive door panel or intercom calls. Do not disturb mode will be activated for 1 hour. To
deactivate do not disturb mode before the end of the 1 hour, see section '4.4 To deactivate do not disturb mode' on p. 21.
Selection screen
For ours8 h
Normal
Do not disturb
Always
For 1 ourh
Continued from previous page.
VESTA2 SE GB2 MONITOR
1st menu screen
Main menu
Camera Door/
Intercom function
Image memory
Do not disturb
1st menu screen
Main menu
Camera Door/
Intercom function
Image memory
Do not disturb